i've searched and with no avail i have found nothing...in all of the threads dealing with the ITR sidemarker placement on the fenders the links were dead...so i was wondering if those of u with JDM itr conversions or if any of u guys have a template for the fender than if u could either take a pic or post it up...im going to install sidemarkers on my friends integra and another friends ITR usdm spec so i want to get it in the right place...thanks to all that can help

 

bump cuz i used to live in rancho cucamonga

 

tyte...hopefully someone has it out there

 

JDM fenders have holes in them from the factory.

I'd warn against cutting holes into your USDM fenders, but that's just MHO.

 

well im going to do it anyways cuz i've done about 5-6 civics (Mainly 7thgen) and a couple of DA integras...but i need a JDM template for the DC2 from honda or someone who has JDM conversion done to send me pics of measurement marks on masking tape on thier fenders if anyone would actually go through the hastle of it

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by ragingSPAM &raquo;</TD></TR><TR><TD CLASS="quote">well im going to do it anyways cuz i've done about 5-6 civics (Mainly 7thgen) and a couple of DA integras...but i need a JDM template for the DC2 from honda or someone who has JDM conversion done to send me pics of measurement marks on masking tape on thier fenders if anyone would actually go through the hastle of it</TD></TR></TABLE>

There is no template.

To be honest, you'll have better luck posing this question in the "Integra" forum. I don't think you'll receive good feedback in this thread as installing sidemarkers and other useless cosmetic "upgrades" are frowned upon in this forum.

 

arn't the fenders different on the JDM from the USDM..meaing a template wont line up with your fenders, so theres not point to measuring it...just put it where it looks good.

 

Reid ... why don't you just move the thread ... and therefore help the poor guy out! LOL!

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by citrus3000psi &raquo;</TD></TR><TR><TD CLASS="quote">arn't the fenders different on the JDM from the USDM..meaing a template wont line up with your fenders, so theres not point to measuring it...just put it where it looks good.</TD></TR></TABLE>
well JDM Integra SIR's have the standard two eye front end and they come with sidemarkers from the factroy. Maybe he need a template or measurement from that

 

Just put them where it looks good.

 

they will line up...the fenders from middle of the wheel well and back are exactly the same...u can even take usdm fenders and make them into the ITR jdm front fenders...i've seen it done

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by JunelSiR &raquo;</TD></TR><TR><TD CLASS="quote">





</TD></TR></TABLE>

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by BlackSage &raquo;</TD></TR><TR><TD CLASS="quote"> </TD></TR></TABLE>

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by PatrickGSR94 &raquo;</TD></TR><TR><TD CLASS="quote">

I made this pic, should be all you need. Align the forward edge of the sidemarker with the point at which the fender crease hits the edge of the fenderwell, and have the top edge of the sidemarker sit about ~3/4" below the bodyline that runs down the side of the car (the one just below the door handles).</TD></TR></TABLE>

 

awesome...thanks you guys i apreciate it a lot

 

http://www.integra.orcon.net.nz/indicator.htm

hope this helps

 

ohh

 

well that site does help but not for this project...its for the DA integra's....and thats what i used for the older integs that i did....thanks anyways