Ported JDM ITR 4-1 Header with Gasket/Skidplate/Thermotec
Thread Starter
Joined: Jul 2004
Posts: 259
Likes: 0
From: Parkville, MD, Baltimore County
Ported JDM ITR 4-1 Header with Gasket/Skidplate/Thermotec
For Sale:
Used 6 months, purchased brand new from hmotorsonline.com.
JDM ITR 4-1 HEader with jdm 2.5 donut gasket, wrapped in thermotec exhuast wrap including http://www.fastlineperformance.com aluminum race skid plate
featuring
dyno proven ( http://www.importreview.com - go to itr 4-1 modified/ported header dyno)
This baby has been professionaly ported inlets with strengthening welds placed on the outside diameter of each primary tube meeting at the exhaust flange. This header is great for all vtec motors b16/b17/b18c or even an ls/crvtec setup!
have a slammed car and worried about flattening your precious JDM header when you bottom out?!? have NO FEAR, the fastline performance skidplate bolts right up to the factory heatshield brackets and provides SERIOUS protection for your tubes. I had this header on a real low riding crx with a b16 and never ever dented it because of this skid plate. Dented headers make bad HP and nobody wants that!
The thermotec wrap is 6 months old and does an amazing job keeping exhaust temps high in the pipes not in the engine bay! This sweet wrap keeps your intake + motor cool and safe from the large amount of heat most stainless headers give off.
The header helped me on my way to 190 whp b16 and just kept making power all the way up to 8,800 rpms. I love my header and the only reason for selling it is because ive moved on to a race only hytech side exit and would like to see someone else's project benefit rather then be selfish and store this piece of jdm quality in my garage
Ive payed over 400 for her and have put atleast another 300 dollars in modifications into her but will she sell for 5, 6 even 700 dollars?!?! Hell NO!
Im trying to get a fast sale im only asking 300 dollars for it. It's midly used, only really seen the street for 3 months and the dyno for an hour
For pics email me @ towsonb16@hotmail.com or call 410-382-5098
You can respond by replying to this post or email/call the numbers above.
Shipping would be around 25-35 dollars in the US or local pickup is available. Thanks for looking.
Used 6 months, purchased brand new from hmotorsonline.com.
JDM ITR 4-1 HEader with jdm 2.5 donut gasket, wrapped in thermotec exhuast wrap including http://www.fastlineperformance.com aluminum race skid plate
featuring
dyno proven ( http://www.importreview.com - go to itr 4-1 modified/ported header dyno)
This baby has been professionaly ported inlets with strengthening welds placed on the outside diameter of each primary tube meeting at the exhaust flange. This header is great for all vtec motors b16/b17/b18c or even an ls/crvtec setup!
have a slammed car and worried about flattening your precious JDM header when you bottom out?!? have NO FEAR, the fastline performance skidplate bolts right up to the factory heatshield brackets and provides SERIOUS protection for your tubes. I had this header on a real low riding crx with a b16 and never ever dented it because of this skid plate. Dented headers make bad HP and nobody wants that!
The thermotec wrap is 6 months old and does an amazing job keeping exhaust temps high in the pipes not in the engine bay! This sweet wrap keeps your intake + motor cool and safe from the large amount of heat most stainless headers give off.
The header helped me on my way to 190 whp b16 and just kept making power all the way up to 8,800 rpms. I love my header and the only reason for selling it is because ive moved on to a race only hytech side exit and would like to see someone else's project benefit rather then be selfish and store this piece of jdm quality in my garage
Ive payed over 400 for her and have put atleast another 300 dollars in modifications into her but will she sell for 5, 6 even 700 dollars?!?! Hell NO!
Im trying to get a fast sale im only asking 300 dollars for it. It's midly used, only really seen the street for 3 months and the dyno for an hour
For pics email me @ towsonb16@hotmail.com or call 410-382-5098You can respond by replying to this post or email/call the numbers above.
Shipping would be around 25-35 dollars in the US or local pickup is available. Thanks for looking.
Thread Starter
Joined: Jul 2004
Posts: 259
Likes: 0
From: Parkville, MD, Baltimore County
Re: Ported JDM ITR 4-1 Header with Gasket/Skidplate/Thermotec (2000Ek)
no, im new to HT, I don't even no how to post pics but ill email you some pics if you pm me your email address.
but ill email you some pics if you pm me your email address.
Honda-Tech Member
Joined: Feb 2003
Posts: 2,007
Likes: 0
From: upskirtsville, NJ
Re: Ported JDM ITR 4-1 Header with Gasket/Skidplate/Thermotec (towsondragcrx)
can you email or send me pics some how ( jasonbouchard@comcast.net)
Trending Topics
Joined: Feb 2004
Posts: 340
Likes: 0
From: Buro, USA
Honda-Tech Member
Joined: Aug 2003
Posts: 1,530
Likes: 0
From: California Love
Re: (2000Ek)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 2000Ek »</TD></TR><TR><TD CLASS="quote">Tracking # please. Paypal'd the money on July 29th.</TD></TR></TABLE>
hope u get ur trackin #
hope u get ur trackin #
Joined: Nov 2003
Posts: 1,769
Likes: 0
From: NorCal
Re: (bl@sterVT)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by bl@sterVT »</TD></TR><TR><TD CLASS="quote">damn you still havent gotten it?</TD></TR></TABLE>
I know. He pm'd last night saying that it had been sent out FedEx ground, but I have yet to get a tracking number. Might have to give my credit company and Paypal a call.
I know. He pm'd last night saying that it had been sent out FedEx ground, but I have yet to get a tracking number. Might have to give my credit company and Paypal a call.
