FS: lsvtec engine or complete swap
decided to keep the car, and im going to sell the engine as my initail means of starting to financing graduate school.
im willing to sell this as a complete swap or just teh engine long block if interested
please on serious offers only, test drives are availble you.
Motor: ls vtec
-99 p30 si head, ported and polished,
-itr port matched intake manifold
-prelude type S t-body
-warm air 3in intake
-93 b18a block, new p30 pistons, shotpeened rods, blananced and polished crank, new bearings for rods and mains, thrust washers etc... engine is broken in nicely compression around 11.6:1-11.7:1
-7lb clutch masters flywheel
-Jun Stage 3 Cams
-Jun Titanium Retainers
-Jun Valve Springs
-skunk 2 chipped p28 ecu, obd2-1 converter harness
-jdm honda 4-1 header ceramic dipped
-95 sir2 jdm tranny with optional lsd
-act 6puck unsprung clutch disc with type R pressure plate
-B&M Fuel pressure regulator
-RC 310 injectors
-usdm type R valve cover
looking to get 4,000 for teh swap or 2500 for the long block.
engine has about 6000miles on it, dynoed 190/133 with denotation from 7k up, ran too much timing, should have no problem breaking 200 with more tuning.
buyer handles all shipping.
here is a link to teh image of the head porting, its a very large image.
http://members.***.net/dsturla/100-0088_IMG.JPG
email or PM me
thanks- dan sturla
NOT PARTING OUT!!!!
Modified by b20bastard at 10:13 PM 9/25/2003
im willing to sell this as a complete swap or just teh engine long block if interested
please on serious offers only, test drives are availble you.
Motor: ls vtec
-99 p30 si head, ported and polished,
-itr port matched intake manifold
-prelude type S t-body
-warm air 3in intake
-93 b18a block, new p30 pistons, shotpeened rods, blananced and polished crank, new bearings for rods and mains, thrust washers etc... engine is broken in nicely compression around 11.6:1-11.7:1
-7lb clutch masters flywheel
-Jun Stage 3 Cams
-Jun Titanium Retainers
-Jun Valve Springs
-skunk 2 chipped p28 ecu, obd2-1 converter harness
-jdm honda 4-1 header ceramic dipped
-95 sir2 jdm tranny with optional lsd
-act 6puck unsprung clutch disc with type R pressure plate
-B&M Fuel pressure regulator
-RC 310 injectors
-usdm type R valve cover
looking to get 4,000 for teh swap or 2500 for the long block.
engine has about 6000miles on it, dynoed 190/133 with denotation from 7k up, ran too much timing, should have no problem breaking 200 with more tuning.
buyer handles all shipping.
here is a link to teh image of the head porting, its a very large image.
http://members.***.net/dsturla/100-0088_IMG.JPG
email or PM me
thanks- dan sturla
NOT PARTING OUT!!!!
Modified by b20bastard at 10:13 PM 9/25/2003
hyped on the head,would u be willing to part out jus the head,who ported the head,what kinda port was done, would u be willing to trad the head-manifold-valvetrain except for cams,valvecover,and b&m fuel reg for my 15 inch gunmetal regamasters with 80% tread dunlops
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post



