SELLING MY MOTOR! lots of goodies!!!!!!!
Thread Starter
Junior Member
Joined: Mar 2002
Posts: 392
Likes: 0
From: Irvine, CA, USA
SELLING MY MOTOR! lots of goodies!!!!!!!
SIR 2 B16A ENGINE HAS NO MILES SINCE ASSEMBLY!!!!
this motor was built to break 200whp n/j
ran out of cash so i'm getting rid of it
JUN TYPE 3 CAMS(these are the revised ones that are thicker and have no grenade pins)new
JUN dual valve springs...new
JUN titainium retainers..new
JUN cam gears
NEW itr int and exh valves
ported polished and milled .30 head...new
one layer head gasket
stock bottom half (this motor was originally a buddy's motor been on neo syn. 5w30 since it came to america)
ported IM
mystery ported TB
all sensors, distr., etc included
all seals, gaskets, belts, pumps, wires, cap, rotor blah blah blah have been replaced with NEW factory parts
JUN ultra light flywheel
act ext plate 6 puck clutch
'94 b16a lsd tranny
rerouted coolant lines
obd 1 p30 ecu unchipped
98 spec axles
shift linkage complete
98 spec harness( will need to re pin a little)
spent over $6000 to build
[B$4,500 obo
[/B]
E-mail for block #'s
[Modified by ****@A51, 1:35 AM 3/25/2003]
[Modified by ****@A51, 8:51 AM 3/31/2003]
[Modified by ****@A51, 8:52 AM 3/31/2003]
Modified by ****@A51 at 7:32 AM 5/31/2003
this motor was built to break 200whp n/j
ran out of cash so i'm getting rid of it
JUN TYPE 3 CAMS(these are the revised ones that are thicker and have no grenade pins)new
JUN dual valve springs...new
JUN titainium retainers..new
JUN cam gears
NEW itr int and exh valves
ported polished and milled .30 head...new
one layer head gasket
stock bottom half (this motor was originally a buddy's motor been on neo syn. 5w30 since it came to america)
ported IM
mystery ported TB
all sensors, distr., etc included
all seals, gaskets, belts, pumps, wires, cap, rotor blah blah blah have been replaced with NEW factory parts
JUN ultra light flywheel
act ext plate 6 puck clutch
'94 b16a lsd tranny
rerouted coolant lines
obd 1 p30 ecu unchipped
98 spec axles
shift linkage complete
98 spec harness( will need to re pin a little)
spent over $6000 to build
[B$4,500 obo
[/B]
E-mail for block #'s[Modified by ****@A51, 1:35 AM 3/25/2003]
[Modified by ****@A51, 8:51 AM 3/31/2003]
[Modified by ****@A51, 8:52 AM 3/31/2003]
Modified by ****@A51 at 7:32 AM 5/31/2003
Thread Starter
Junior Member
Joined: Mar 2002
Posts: 392
Likes: 0
From: Irvine, CA, USA
Re: SELLING MY MOTOR! lots of goodies!!!!!!! (****@A51)
vortech fpr is also on the motor...and I will let it go for $4k. THe head parts are all brand new. U can't even get JUN 3's anymore!
Thread Starter
Junior Member
Joined: Mar 2002
Posts: 392
Likes: 0
From: Irvine, CA, USA
Re: SELLING MY MOTOR! lots of goodies!!!!!!! (****@A51)
The engine was assembled while I worked at Area 51 in socal. (if you've heard of it) Sy Nakashima (formerly of JUN) ported the head, Charles Madrid and I assembled the motor. The engine was built for 9000+ rpm for my wchc h-1/TCRA 2.2L cup race car which is on hold for lack of cash flow.
Trending Topics
Thread Starter
Junior Member
Joined: Mar 2002
Posts: 392
Likes: 0
From: Irvine, CA, USA
Re: SELLING MY MOTOR! lots of goodies!!!!!!! (****@A51)
Before u pm me; no I will not sell the Jun 3's alone...
no I will not trade my parts for other parts...
and again No Lowballers! u know who u are...
no I will not trade my parts for other parts...
and again No Lowballers! u know who u are...
Honda-Tech Member
Joined: Nov 2001
Posts: 4,629
Likes: 0
From: Flying in my F16..Cleeean Ayyy
Re: SELLING MY MOTOR! lots of goodies!!!!!!! (****@A51)
U can't even get JUN 3's anymore!
Bump for a sick *** head
