rbjeepthing's Build Thread Everyone Else Is Doing It (EF Content)
Thread Starter
Honda-Tech Member
Joined: Oct 2005
Posts: 118
Likes: 0
From: Barrie, Ont, Canada
rbjeepthing's Build Thread Everyone Else Is Doing It (EF Content)
So I figured I would start a build thread. I have had this shell for about 4 years now and the rest of the car since 2000. I have some plans for the winter so far this is what I have ordered or will be ordering and some of the stuff I have picked up.
First part done today at work
Got around to installing my Innovative front cross member replacement with new energy suspension bushings and a new Mishimoto half rad with Mishimoto B16 specific silicone hoses. Over all the install was pretty easy and netted me a lot of clearance if I go Boost or with a 4-1 header. Also the fit and finish was amazing! I have never had an easier time installing aftermarket products on a vehicle. Guess you get what you pay for.
Part numbers used:
Innovative Cross Member #59111 (Teknotik)
Innovative Upper Rad Stay #59100 (Teknotik)
Energy Suspension Radius Arm Bushing Set #167102G (My Work)
Mishimoto Rad #MMRAD-CIV-92 (Teknotik)
Mishimoto Silicone Hoses #MMHOSE-CIV-88B16 (Teknotik)
Proform (1000cfm) 10" Fan #67010 (My Work)
Honda Rad Bushing Lower x 2 #74172-SR3-22 (My Work)
Honda Rad Bushing Lower x 1 #74173-SJ4-000 (My Work)
- GSR Full Brake Conversion
- BWR Rear Lower CA
- Meghan Toe Arms
- Meghan Camber Arms
- PIC Select 10k-12k
- Innovative Front Cross Member
- Mishimoto EG Rad and Fan
- Mishimoto Silicon Hoses Complete Cooling System B16 to EF
- Proform 10 " Fan
- Russel SS Brake Lines
First part done today at work
Got around to installing my Innovative front cross member replacement with new energy suspension bushings and a new Mishimoto half rad with Mishimoto B16 specific silicone hoses. Over all the install was pretty easy and netted me a lot of clearance if I go Boost or with a 4-1 header. Also the fit and finish was amazing! I have never had an easier time installing aftermarket products on a vehicle. Guess you get what you pay for.
Part numbers used:
Innovative Cross Member #59111 (Teknotik)
Innovative Upper Rad Stay #59100 (Teknotik)
Energy Suspension Radius Arm Bushing Set #167102G (My Work)
Mishimoto Rad #MMRAD-CIV-92 (Teknotik)
Mishimoto Silicone Hoses #MMHOSE-CIV-88B16 (Teknotik)
Proform (1000cfm) 10" Fan #67010 (My Work)
Honda Rad Bushing Lower x 2 #74172-SR3-22 (My Work)
Honda Rad Bushing Lower x 1 #74173-SJ4-000 (My Work)
Last edited by rbjeepthing; Oct 16, 2010 at 11:22 AM.
Thread Starter
Honda-Tech Member
Joined: Oct 2005
Posts: 118
Likes: 0
From: Barrie, Ont, Canada
Re: rbjeepthing's Build Thread Everyone Else Is Doing It (EF Content)
Thanks man
I added a little something to the build list. Gave into my buddies and have abandoned NA ordered this yesterday should see it within 48 hours. So stoked for boost!
Garrett T3 / T4E 57 trim
* Custom built, hybrid turbo assembled from a combination of NEW and reman to new components that are 100% genuine Garrett and in respect, if not exceeding all original requirements.
6 months warranty.
TURBO SPECIFICATIONS:
compressor wheel: 56.6 / 74.9 mm 57 trim
compressor housing: T04E 0.70 a/r, 4" / 2½"
center section: oil cooled journal bearings
Turbine wheel: 68 trim (stage1)
I added a little something to the build list. Gave into my buddies and have abandoned NA ordered this yesterday should see it within 48 hours. So stoked for boost!
Garrett T3 / T4E 57 trim
* Custom built, hybrid turbo assembled from a combination of NEW and reman to new components that are 100% genuine Garrett and in respect, if not exceeding all original requirements.
6 months warranty.
TURBO SPECIFICATIONS:
compressor wheel: 56.6 / 74.9 mm 57 trim
compressor housing: T04E 0.70 a/r, 4" / 2½"
center section: oil cooled journal bearings
Turbine wheel: 68 trim (stage1)
Thread
Thread Starter
Forum
Replies
Last Post
JDMHN8
Honda CRX / EF Civic (1988 - 1991)
15
Jan 8, 2004 01:01 AM
