So i sold my 92 dx civic 4dr, with a d15b in it and got this Integra.so let me know what you think from the pictures.


AND here is my new 95 Integra.







well the first thing i did to the car was fix some oil leaks. Like the cam seal.



after that i did nothing to the car for about 3 mouths, to save some money.


so the car had a cold air intake in the trunk, so i put it on.


the air filter is very low on the car.



the i traided my fat-5 for 2 sets of rims. one set was some american racing and the others were Konig Monsoon.

they were painted all white, so i took the paint off them and im going to be painting them soon.

got them like this:


got the paint off:


primered:


next i took off the tail lights that were blacked out, and took it all off.
befor:

after:


I also put a new fender on it and going to put a new diver side door on it.

And i got some 5000k high beams for the car to day.



also got these goodys


more will be up soon

 

cool..wat r ur plans?????????? good start bro

 

plans are to end up with a b16 under the hood, lower the car, get it looking clean, and have a car in the end that im proud to call mine.

 

why a b16 under the hood? how about b16 head on top of that block

 

i would but it has about 250k mils on that engine

 

this thread has potential written all over it

 

here is the rim with some paint on it.



now im thinking of taking the side moulding off the car, what do you guys think would look better?

 

well thank you, i was hoping it would

 

good setup up from the civic, the integra looks good.

To take the molding off the sides, you would need to close/weld the holes that they leave from the clips, so its a little more intensive than many think.

 

yeah i knew i had to do some hole filling. but i still dont know if i want to do it or not

 

watch out for puddles with that intake. i had a similar intake on my civic & ran it through a huge puddle on accident. needless to say it hyrdolocked. but i still drove it around for 2 months with a bent wrist pin till it sent a rod through the block haha.

 

yeah i only have it on for the summer time, then ill change it to a short ram. But yesterday we had a summer storm here and it flooded out the streets, it when from 106 and sunny to super dark and rainy. i hope the car is going to do ok.

 

So i need to get gas, and the only place what was near by was an AM/PM, so i got some 87 gas. then started to drive to my friends house, when my car started to die on and off and when i pushed on the gas nothing would happen, then it would pop back to normal, the mess up agien......

So I always go to chevron and get 91. so mixing the gases was not sitting well with the car, so i got new spark plucks and some wires

here is my old spark plugs, so out with the old in with the new



yeah new NGK's


and here is the new wires


every thing is better now yay

 

ok. You going to swap it for b16.. Good luck because doing it right need money.. I was going to swap my 4 door sedan for b16 but change mind because didn't want to break bank budget..

 

i would slap that B16 head on and rebuild the block. otherwise good plans.

 

And here is one of the finished rims. yay!

 

what do you meen that it would take a lot of money? all you need to do is get the engine, get a new wiring harrness, and a new ecu and wire up vtec. it dosent seem to bad. unless there is somthing i dont know about

 

i would rebuild it but this car is my dd and i work 5-6 days a week, so i cant take the time to get the botton end rebuilt. i would like to tho.

 

Those look good! What paint did you use

 

this kind:

 

and here is a new toy i got for the car to day for $40



then i looked under the car and it already has one.....yay i guess. so now i need to sell it haha

 

**** is going to be mad freshhh love the red rims

 

thx i just need to get some tires on them. then on the car they go.

 

well i had to get a new heater hose today becuz the old one poped.... i hate when that happens. and its always when you have to drive somewere.

 

LOL.

keep it up