Parting out 9 sec capable hatch..
Thread Starter
Honda-Tech Member
Joined: Feb 2006
Posts: 102
Likes: 0
From: Mobile, AL, USA
Parting out 9 sec capable hatch..
Parting out my 92 cx hatch. They car made 417 @ 17 psi on a very conservative quick tune.. Never seen over 17 psi or race gas. Everything has less than 500 miles (except for trans, axles and stuff like that). He tried selling it for $7500 but no buyers so screw it were parting it out. All Items are listed WITHOUT shipping and paypal fees unless NOTED.
Turbo kit: BEP S366, coated exhaust housing, AFI top mount manifold, Tial 44 wastegate, 3” stainless downpipe $2000
Engine: 84mm LS, Benson sleeves, eagle rods, CP pistons 9.5:1, GSR oil pump, GSR water pump, ARP headstuds, ACL Bearings, B16 head, Supertech dual valve springs and ti retainers, fresh valve job, new valve seals, ported and polished, Type R cams, STR cam gears, MSD plug wires, MSD cap and ex MSD coil, new dist. $2700 will separate for $900 for head and $2000 for bottom end.
Intake manifold: Victor x ported to match head $200------sold
70mm blox TB, used $100-------sold
72mm blox TB, brand new $150-------sold
Catch can set up: T1R catch can, 4 -10 stainless lines with black russel fittings, $450
Clutch: CC stg 5 clutch, only 500 miles, $285
Bogart Drag wheels Front/rear. 13x8 with 24.5MT slicks, Rears are 15x5? w/ no tires. Requires extended studs up front. $600------sold
Stainless clutchline: $make offer-----sold
CC lightweight flywheel, $100
B16 trans with quaife, shifts fine $900
Fuel system: AEM AFPR, AEM fuel rail, fuel pressure gauge, Bosch 1600 cc injectors, Jegs inline fuel filter, stainless lines, walbro 255, $450
FMIC kit, 4” ebay core, TIAL BOV on IC core, full 3” piping painted gloss black with PPG concept paint. $400
Golden eagle vacuum block, Black, $make offer
P28 with Hondata S100, $200
Digital 6 box, $250
Chassis: 92 cx hatch, Fresh paint, black roof and hood. Hood has molded scoop for turbo fitment when we had full race manifold. Hood is flat black, PPG deltron used on body and PPG concept used on roof. Engine bay was full shaved. CF duckbill wing, clear coated taillights. Interior is clean, aftermarket steering wheel, 8 pt S&W cage. New windshield and belt moldings. no name coilovers, LS MESH wheels, extended studs,S14 seats for tall people lol.. $2000
If you dont like the prices throw me an offer, its best to email me cause Im never on honda-tech that much anymore. Email is JWORM31185@aol.com or text 251-533-2575
Turbo kit: BEP S366, coated exhaust housing, AFI top mount manifold, Tial 44 wastegate, 3” stainless downpipe $2000
Engine: 84mm LS, Benson sleeves, eagle rods, CP pistons 9.5:1, GSR oil pump, GSR water pump, ARP headstuds, ACL Bearings, B16 head, Supertech dual valve springs and ti retainers, fresh valve job, new valve seals, ported and polished, Type R cams, STR cam gears, MSD plug wires, MSD cap and ex MSD coil, new dist. $2700 will separate for $900 for head and $2000 for bottom end.
Intake manifold: Victor x ported to match head $200------sold
70mm blox TB, used $100-------sold
72mm blox TB, brand new $150-------sold
Catch can set up: T1R catch can, 4 -10 stainless lines with black russel fittings, $450
Clutch: CC stg 5 clutch, only 500 miles, $285
Bogart Drag wheels Front/rear. 13x8 with 24.5MT slicks, Rears are 15x5? w/ no tires. Requires extended studs up front. $600------sold
Stainless clutchline: $make offer-----sold
CC lightweight flywheel, $100
B16 trans with quaife, shifts fine $900
Fuel system: AEM AFPR, AEM fuel rail, fuel pressure gauge, Bosch 1600 cc injectors, Jegs inline fuel filter, stainless lines, walbro 255, $450
FMIC kit, 4” ebay core, TIAL BOV on IC core, full 3” piping painted gloss black with PPG concept paint. $400
Golden eagle vacuum block, Black, $make offer
P28 with Hondata S100, $200
Digital 6 box, $250
Chassis: 92 cx hatch, Fresh paint, black roof and hood. Hood has molded scoop for turbo fitment when we had full race manifold. Hood is flat black, PPG deltron used on body and PPG concept used on roof. Engine bay was full shaved. CF duckbill wing, clear coated taillights. Interior is clean, aftermarket steering wheel, 8 pt S&W cage. New windshield and belt moldings. no name coilovers, LS MESH wheels, extended studs,S14 seats for tall people lol.. $2000
If you dont like the prices throw me an offer, its best to email me cause Im never on honda-tech that much anymore. Email is JWORM31185@aol.com or text 251-533-2575
Last edited by LowNismo17; Jan 11, 2010 at 05:43 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Bulldogg83
Classifieds: Forced Induction
21
Sep 30, 2004 11:34 AM
