Please read the rules for the new thread. At the end of each month this thread will be unstickied, and a new thread created in this one's place. If you haven't sold your parts, you may post them in the new month's thread. DO NOT BUMP THE OLD THREAD

1) This is for RaceCar parts ONLY. No body panels, fenders etc allowed, unless it is a full race front end. ABSOLUTELY NO useless OEM parts!
2) Do NOT repost your thread over and over hoping to get it on a new page. If your parts sell please remove them from your post. If you sell everything off of your list of parts, report your post to moderator by clicking on the just under your user name and we will delete it.
3)You are ONLY allowed ONE post in this thread. If you are found to have more than 1 post, in the FS sticky all of your posts in the sticky will be deleted, and you will be given an infraction. With enough infractions you will be banned
4) NO WTB ADS!
5) NO COMMERCIAL POSTS AT ALL THIS MEANS, IF YOU OWN A SHOP DO NOT POST BRAND NEW PARTS IN HERE
6) Please provide all pertinent information, including price, and try to return pm's.

We will delete any BS we feel does not belong in here


Please try and limit the size and # of pictures you post. using thumbnails would be fantastic.

 

FS-GT3582R no miles just idled on. Had issues and tore everything back down.(turbo on the left)
1150obo

FX500 4puck clutch taking reasonable offers. comes with a fresh ACT flywheel. Only idled on. B-series clutch

 

This the last of my turbo setup...

NO TRADES

Aluminum 2.5” intercooler piping made by S&R performance. Tested to 100psi with zero issues. Light and dissipates heat quickly. flanged for Tial BOV. $250 with all clamps and couplers. Fit DC/JDM integra, may fit others as well.



3” Aluminum exhaust built by S&R performace it weighs maybe 5lbs. Fits DC integras, possibly others. Can be run as a dump or with the magnaflow muffler. It looks stock. You can barely here it idle, but it sounds great when you open it up. $400

 

Edelbrock GSR Victor X, new in box $320 shipped


-BluePrint B-Series dual valve springs and Titanium retainers - new in box $250 shipped


-96-98 Civic ram air headlight, all molded fiberglass, 1 of a kind, uses stock mounting locations and fits nice - $75 shipped



-Taylor 48100 battery box...brand new in Summit box (i ordered it by accident) - SOLD

 

Revo Technica Stage 2 Front Camber Correction Arms used for quarter of a season less then 8 times at the track. With years of experience in the automotive industry, Revo's Research and Development Team designed this camber arm carefully keeping in mind clearance issues and maximum adjustability. Constructed from 1015 Grade steel and manufactured as a 1 piece design offers added strength and reliability. This design allows 0 to +3 degrees adjustability and is a direct bolt on for easy installation. Please contact your authorized Revo Technica distributor for more information and sales. Part Number: CC60-8891F Application: Honda Civic 1988-1991 (all models) Honda CRX 1988-1991 (all models)$120.00 OBO




B series half shaft $60.00 B series starter SOLD

 

92-93 b series cable trans (ys1) Has the following parts inside and I can remove to verify for serious buyers only: B16 1st 2nd and 3rd, GSR 4th, Pro Drive ring and pinion 4.70 final drive, Phantom Grip trans cuff, Nitro driveline spool... I also have 5th gear if you want it back in the trans and 1 extra case. All parts will fit in a hydro case. $900 (pick up only)

 

F.SGarrett GT35R, never used. Polished ported shrowd S cover. Twin scroll vband exh housing $1350 shipped







Wheels only. They sell new for $680 a set, $560 shipped (continental US) for the set of wheels only

These are in perfect shape. no scratches or chips.

 

prices do not include shipping or paypal fees unless we work something out

Crower springs and titanium retainers, about 4500 miles. $300


YS1 LS cable tranny from 92-93 with HAsport cable to hydro kit. needs 3rd gear synchro. $275 or I can put in a new synchro for additional cost.


JDM B16A bottom end with about 45K miles. ran perfect when pulled for a poor mans type-R swap. ~SOLD~

 

- Weld Racing 15 x 8 black with gold centers. In mint condition...
4 x 100 (The rims are already drilled for rims screws, will include.)

Asking $ 650.00 OBO

- Avid B-series Pro-Series engine mount kit, used in great condition Asking $ 300.00 OBO

- Avid Racing Pro-Series traction bar kit, used in great condition Asking $ 225.00 OBO

- Aeromotive A1000 Fuel pump - used Asking $ 195.00 OBO

- Skunk2 Racing Billet Aluminum LCA, in mint condition Asking $ 175.00 OBO

- Skunk2 Racing lower tie bar, in mint condition Asking $ 80.00 OBO

- Autometer water temp guage, phantom white new in a box - $ 40.00 OBO

- Autometer phantom tach with shift light, new in a box $ 125.00 OBO


PM me or email me at yzfr6avid@gmail.com

 

-93cx clean title
-2yr old paint
-10pt cage NHRA certified
-Stroud window net and parachute
-Morroso Battery box relocated to trunk
-Morroso Kill switch
-Custom Batt. charging terminal located next to Batt.
-Engine bay painted flat black w/ wire tuck
-Carbon fiber hood
-Sparco hood pins
-VIS carbon duckbill spoiler
-Type R style front lip
-Custom Rear Bumper diffusers

-AEBS sleeved B20 block
-Micro polished LS crank
-84mm coated JE Pistons 10:1
-Pauter Rods
-ATI race Damper
-Rotating assy. balanced by Miller
-Type R Oil and water pump
-Golden Eagle Oil Filter Sandwich plate
-Morroso Oil pan w/ GE magnetic drain plug

-B16 Head
-Race port and polish by Miller
-Supertech Springs & Retainers
-Supertech 1mm oversized Nitrate Valves
-Golden Eagle Cam seal
-Golden Eagle Head studs
-Brian Crower Cams
-Skunk2 pro series cam gears
-Toda Timing belt
-JG Edelbrock port matched IM
-Hondata IM gasket
-Ericks Racing 74mm TB w/ Addel Wiggins Clamp
-AEM 5bar Map sensor
-Powder coated vented Valve cover
-NRG custom breather tank w/ 6 -10 lines
-PWR aluminum Radiator w/ high power Fan
-12an Coolant lines
-Morroso Radiator over flow tank

-B16 Tranny w/ Quaife LSD
-Competition Clutch Twin Disk
-Honda MT Fluid
-Golden Eagle Scatter Sheild
-DSS stage 5 axels w/ ARP extended Studs
-Avid Racing Solid Billet Motor mounts

-Full-Race T4 Topmount
-Precision Turbo 74mm Qtrim .96ar w/ upgraded shaft
-4in Stainless DP w/ V-band and wrapped w/ thermo-tec
-Tial 60mm WG custom mounted by BigTom
-Dump tube wrapped w/ thermo-tec
-Precision 750hp IC back doored on one side
-3in. Alumin. IC piping all around

-Twin SX engineering Fuel pumps
-Paxton Fuel filters
-Competition Engineering Fuel sump
-10an fuel lines
-NOS Y Block
-Golden Eagle Fuel Rail
-Aeromotive Fuel regulator
-Summit Fuel Sample valve
-Precision 1600cc injectors
-FJO injector Driver
-M&W Pro10 ignition
-Crane Coil
-MSD spark plug wires
-NGK plugs
-Hondata S300 w/ boost by gear
-Hondata Boost Solenoid

-D2 Drag Coilovers 18k rear 12k front 32way adjustable
-Skunk2 Front camber kit
-Omni power Front LCA's
-Full-Race Traction bars
-Skunk2 rear LCA's
-Benen Industries rear lower arm bar
-Russel Stainless brake lines
-Power Slot slotted rotors
-Hawk HP pads
-Black Rota slipstreams 15x7 4x100
-MT Drag Radials 225x50x15

-Sparco Pro2000 Seats
-G-Force 5pt. Harness (driver)
-NRG Innovations Slim quick release
-Mugen Steering wheel
-Mugen Pedel kit
-JDM SIR Gauge Cluster
-JDM accessory Din Station
-JDM type R shift boot
-Spoon Shift ****
-HOP Radio delete
-GSR shift linkage w/ ES poly bushings
-Broadway rear view mirror
-Apexi boost gauge
-Defi Oil press. gauge
-Defi EGT gauge
-Auto Meter Water temp. gauge
-MSD LED shift light

..The Price is 18K. Thanks for looking









New Pics! This is how the hatch sits now

 

Complete part out of my car. Nothing includes paypal fees or shipping. Everything is OBO (best offer). Please PM me if you have any questions. Thanks.

-IPS KT1 Cams $SOLD
-K20 Sidewinder Manifold T4 w/44mm wastegate flange $850
-EP3 Tansmission w/ Quaiffe LSD $SOLD
-K20 DSS 2.9 axles for EG Civic (fit w/ Hasport Mounts) $550
-K20 EG (92-95) Hasport Mounts $375
-Hybrid K20/EG Sub Harness $225
-Competition Clutch Twin Disc/w Flywheel $775
-Crower Rods $500 (not Brian Crower-The real CROWER)
-RBC Manifold w/ Adapter $SOLD
-KPRO $SOLD
-K20 Golden Eagle Sleeved Block w/ Crank $1000
-K20 Head Built w/o cams $SOLD
-AFI Catch Can w/ Valve Cover and Lines $SOLD
-Intercooler piping 3" $225
-Down pipe w/ small Muffler $250


Nothing has been taken apart yet. Everything is still in the car. Car is also available for TRADE! car was featured in Honda Tuning here:
http://www.hondatuningmagazine.com/f...ack/index.html

You can find ore pictures there on the link above.

More to come.

 

I will ship after payment is received. I will ship USPS Priority Mail for smaller items and FedEx ground for larger items. I will also include a tracking number or delivery confirmation number. Shipped price are for shipping to the 48 States.
I accept money orders, Paypal, and also pickup in the NJ area.
I have many references and vouches H-T, just ask around or I can send you a list.

Contact Info
AIM - Dynoair690
E-Mail – BigTeggie@gmail.com
Paypal - BigTeggie@gmail.com

Please Email as my PM’s fill up quickly

Please click on the thumbnails for larger images

Brian Crower Stage Cams and Valvetrain K20A2/Z3
-All Parts are brand new in the box, only opened to take pictures.
-BC Stage 3 Cams (BC0043)
-BC Spring Retainer kit BC(0040)
-Retail is over $900+shipping
$850 Shipped



DTR/SSR K24 4-1 Header w/Megaphone
-Brand New, Never Used, for EG w/Hasport Mounts
-Has a bolt on megaphone, and also includes a 2.5” to 3” adapter to use an exhaust if you want
-Looking to get what I paid for it
-No need to wait for one to get built
$1150 Shipped


Weld Magnum Wheels and Slicks
-Everything is brand new
-No passes down the track, only touched the ground to move the car around a few times
-Fit perfect on my EG civic with stock brakes
-Front wheels 13x8, 4x100, 5” backspace
-Rear wheels 15x3.5, 4x100
-Front slicks are 24.5”x9 MT’s
-Rear wheels are 24.5” M&H’s
$2000 + Shipping



2 Rota Slipstreams with BFG Drag Radials
-12 runs on the tires and about 100 street miles
-Still a lot of life left on the tires
-Tires are 205/50/15
-Wheels are 4x100, 15x7, Steel Grey
-No scratches or damage to anything
-Everything was kept inside my basement and not outside
$325 Shipped




Lucas 440cc High Impedance B,D,H Injectors
-Great working condition, less than 5k miles
-Upgraded to bigger injectors so no use for them
$200 Shipped


<u>RLZ Stage 3 B-Series Cams</u>
-Used for only 3000 miles, great condition
-Great for serious all-motor setups
$350 Shipped



Corbeau Forza Seats
-Good Condition, can use some cleaning before they go in the car
-One is newer and the logo doesn’t match the other because I didn’t get them at the same time
$200 PICKUP

 

I have a set of Pic performance coilovers, apex 12k fronts, and drag rears 18k. These have 0 miles and in new condition only mounted on the car never ran. I would like to get $750 shipped please pm me if interested thanks

 

^^^^UPDATED^^^^ on 8-25-2009

((( I get 2 FLAKERS a day on this stuff, it HAS TO STOP! I don't go out of my way to take NEW pics, offer fair prices to have you just fall off here or say nevermind, I am broke. Go get a job, a better job, a higher education, etc... I didn't get this stuff for free and nor am i going to hold a PAWN shop atmosphere to sell it for nothing. )))




All top name brands. Everything has 300miles MAX on them. Everything works great I am selling here.

>>>>>-Borg Warner S372R turbo (polished). Less than 10 passes on it. NO SHAFT PLAY, no smoking, IT's Brand new practically. 1.00A/R. Divided T4 inlet. w/ Race Cover option! $1100.00 obo





>>>>>-Circuit worx drive train. Axles, half shaft, GSR hubs and knuckles w/ GSR brakes, and Spool (rated to 800+whp and 28" slicks) $850.00 obo




>>>>>-BDL Fuel Rail with fittings on each end (-10AN) $100 obo



>>>>>-STR polished scatter shield for B series $100 obo





>>>>>-Autronic SMC Standalone. $1000.... Wired for Ek civic but can be modified for any Honda or anyother car with purchase of new harness. Does it all. Comes with MSD ignition box setup for COIL ON PLUG ignition.




Autronic details:
----(here is some info I found on it for you)----

The Autronic SMC is a sequential 3D ECU available in three case styles, standard, sealed and water proof. This is the biggest selling model and is suitable for most applications. The Autronic SMC includes harness, air and water temp sensor, internal map sensor, fuel pump relay, PC data cable, calibration and data logging software, 100 page manual. The internal map sensor is available in 1bar absolute or 4.4 bar absolute (50 psi). Available with high current (low impedance) or low current (high impedance) injector drivers. Harness is a flying lead type and has a connector which plugs into the Ecu, and has a socket for fuel pump relay, and socket for data cable connection to a IBM compatible PC or Laptop serial port. The other end of the harness has to be connected as per the wiring diagram. The software is compatible with USB ports, when used with USB to serial adapter.

Dimensions:
L = 150mm (6 inches)

W = 120mm (4 3/4 inches)
H = 35mm (1 3/8 inches)

Features:
Sequential operation for 2 to 8 cylinder engines and non sequential operation for 10+ cylinders
Eight injector ouputs
Four ignition outputs
3D fuel and ignition maps
User defined up to 32 RPM and 16 Load sites = 512 sites
Anti-lag
Flat Shift (ver 1.19)
Data Logging
Software selectable trigger angle
Support for multi-tooth or missing teeth triggers
Auxiliary outputs other than fuel pump control
8 cyl engine = 1 (1 PWM output)
6 cyl engine = 3 (1 PWM + 2 On/Off)
4 cyl engine = 5(1 PWM + 4 On/Off)
Auxiliary outputs can be defined for boost control, nitrous oxide, camshaft timing, AC, fan control, idle valve etc.
Available with high current drivers if required
AutoTune option available
User choice of manifold absolute pressure or throttle position as engine load input
Single coil distributor, twin coil distributor or muilticoil distributor-less ignition configurations are possible on most engines
Exhaust oxygen sensor input for sensing air/fuel ratio
Diagnostic/Error indicator of sensor or ECU fault conditions with memory for detection of intermittent fault conditions. An external light may also be connected for remote indication of abnormal operation
Precise spark advance control strategy for both static and dynamic operating conditions
Unique calibration strategy allows accurate control of fuel delivery under both acceleration and deceleration
User selectable spark and fuel delivery strategy for abnormal engine operation conditions to minimize possibility of engine damage whilst still maintaining engine operation.. (eg:- over heated or over boosted)
Comprehensive limp-home functions with user selectable default settings that ensure engine operation can continue after sensor failure has occurred
Full compensation of engine control parameters for engine operation at any altitude (fuel delivery, ignition timing and boost pressure)
Adaptive learning (with memory) to minimize the number of user setups required and to provide optimal control of air/fuel ratio, boost pressure and idle stability
Rev limiter with soft characteristic that uses a combination of fuel delivery and spark control
Fuel pump safety shutoff. Pump stops 3 to 4 seconds after the engine stops
nit is ultra light weight/compact yet has sufficient drive capacity for high power continuous duty applications. (one unit OK for all applications from motor cycle to large capacity twin turbo engines)
Optional interface unit to allow sequential operation without the need for separate crank/camshaft sensors or special multi-sensor distributor
Optional Water Proof case for marine or harsh environments

A user friendly Windows software allows the user to select the degree of sophistication required for each application. This program, in combination with intelligence within the management system, allows the user to select the finest calibration detail required to match the application, in absolute minimum of time.
This program provides the means of interrogating the engine management system enabling speedy diagnosis and calibration.

These systems can cater for the requirements of virtually any spark ignition engine, including the following:
High output supercharged or turbocharged engines, with either multi point and/or center point injection
Rotary (Wankel) and two stroke engines
Engines having uneven firing sequences such as 2 and 4 cylinder "V" configuration motor cycle engines and V6 motor vehicle engines
IMPORTANT:- Please note that this product is intended for high performance motor sport applications and compliance with statutory regulations when used on public roads cannot be guaranteed.

Auxilliary Output Function can be used for the following:
losed loop (feedback), boost control for turbocharged engines with rpm and temperature dependent calibration characteristic
Closed loop (feedback) idle speed control
Control of engine cooling fan
Programmable on/off control for solenoid or relay driving that operates according to engine speed and load (eg:- can be used for gear shift control or light, over rev indicator, inlet camshaft timing selection or control of a supplementary electric fuel pump that augments mechanical fuel pump delivery at low engine rpm only)
Fuel used pulse output to electric or electro-mechanical counter with resolution of 0.1 liter (or use with trip computer)
Even more sophisticated control function such as servo control of auxiliary butterfly for turbocharged applications requiring precise throttle control and minimum turbo lag

Inputs:
Ignition input Hall effect, (Also available for direct connection to magnetic reluctor type pick-ups)
No. 1 cylinder reference. (Also available for direct connection to magnetic reluctor type pickups)
Barometric pressure (included)
Manifold pressure
Throttle position (TPS Sensor not included)
Intake air temperature (included)
Engine coolant temperature (included)
Exhaust oxygen (Sensor sold seperately)
Idle mixture trim. (Internal to ECU and screwdriver adjustable from outside)

Outputs:
Open collector ignition output to any of the following:
Single coil high energy ignitions: Bosch 7 pin, Mitsubishi 3 pin
Autronic Capacitor Discharge Ignition (CDI)
MSD 6A etc.
Auxilliary Outputs:
Fuel pump/injector fuel shut off safety relay
Multifunction on/off or pulse width modulation output for either:
Engine cooling fan relay
Idle speed actuator. (Variable duty cycle single pole type, eg:- Bosch)
Turbocharger wastegate control valve. (SEM, most OEM types or Autronic low or high capacity)
Turbocharger auxiliary butterfly control motor
General purpose duty cycle output with user define characteristic
Fuel used pulse output. (for trip computer function)

 

WILLING TO PART OUT STARTING W/CHASSIS $7500.00, civic coupe, ls vtec turbo, full chromally cage w/wheelie bar and chute. all interior sheet metal panels, mb products 1 piece front end, doors, trunk lid and dash, weld wheels and rpm rear susp w/drag magnum rear wheels, custom paint and air brush, too much to remember and list, 10 sec turn key car and consistant. also comes w/20 foot carson enclosed trailer w/air brush on rear door. I will sell car w/out trailer for $12,500 hard times forces sale, serious inquires please. $15,000 firm, no trades. email for additional pix or call me @ (562) 201-0117 cell, (760) 245-8353 after 5pm.















R.C 310 Injectors, nothing wrong. used on a street car w/nitrous. $125.00


Golden Eagle cam gears for B-Series, $125.00 and I will pay shipping and Pay pal charge.




RPM Rear susp for 92-95 civic, integra, brings rear wheels inward for no rubbing and able to drop car rear low. very light and all aluminum w/all adjustable hiem joints. disc rear brakes w/cross drilled rotors, Apex rear struts w/300 lb spring, no brake lines. all complete. No Wheels $650.00

 

FS:

BNIB precision 780 cc injectors
BNIB turbo xs Manual Boost Controller / MBC

Will post pics tonight

 

FS:Turbo kit
-Full-Race ram horn manifold ($600.00)
-Garrett turbo T3/67 (prob 30-40 passes on it) great turbo ($500.00) pending sale
-3in Full-Race down pipe ($250.00)
-TIAL 44mm waste gate (with dump tube) ($350.00)
-S-Max big core intercooler (brand new, NO INTERCOOLER PIPING) ($300.00)
-3in custom full exhaust with Borla XR-1 muffler ($300.00)
-TIAL blow off valve ($200.00)
(this turbo kit on my car ran a 10.5 @140mph SFWD car) was on a ls/vtec set up has more in it, made 600+hp... $2000.00 for this turbo kit... pix will be up soon......
email me @ boostedeg@yahoo.com or pm me......
I am willing to part out (prices are listed) or you can buy the whole kit at a cheaper price.. pick up only, will ship at buyers expense.......

I also have:
Precision 825hp intercooler brand new in box ($500.00)
Inlinepro cast iron log turbo manifold for T3 or T4 turbos brand new in box ($400.00)

 

bnib mfactory diff for k series $575

 

Used Richmond Spool for GSR $250 Does not come with final drive.

Used NOS purge solenoid $25

H22 Web Cams Street version $200

NOS Bottle with blow down tube $80

Evolution Industries GSR Spool Brand New $150

 

Motor is as follows: $4800+shipping!!!! Will Come with everything listed below.

LS block
GE Sleeves w/Orings
CP 84mm pistons with upgrades wrist pins (flat tops 10:1 cp)
Manley rods (LS)
LS crank
Clevite Bearings
OEM Oil/Water pump
LS oil pan Tapped
GE LS/Vtec Kit
GE 84mm head gasket
GSR Head
Fully Ported and Polished by Ryan@Warr heads
GSR Cams
Supertech Springs/Retainers
Supertech Inconel Exhaust valves
Bronze guides
Valve Job
High Amp Alternator
Wiring Harness included
3 Distributors wired for the external coil, 1 LS, 2 GSR's
Edelbrock Intake Manifold (intake port matched)
Stock GSR throttle body
Starter

**Mounts/Trans/Scatter Shield/Breather Kit/Fluidamper NOT Included!**




Custom built Breather kit $400 Shipped! - SOLD!!!
using 2 Moroso Cans with 4 -12an Lines with return into the block
Valve Cover with 4 -12an fittings welding to it and powder coated Gloss Black

Garrett 4294 Journal Bearing $750 Shipped!
Includes Gasket, Feed/Return lines and fittings.








4" Down Pipe w/flex $300 shipped
VERY well constructed to fit RIGHT up against the slave cylinder and oil pan for a tight
fit to help keep room for traction bar & engine catch pan.




4" Aluminum Exhaust - $350 SHIPPED! - PENDING
V-Bands connection at the downpipe and a v band connection
over the rear axle for easy take off. Stock factory routed!

DriveTrain:
Liberty Dog Box transmission with Quaife (GSR ratios, B16 Quaife) $4300 SHIPPED!


Exedy Twin disc Clutch $1050 SHIPPED!
Has Ten Passes on it and approx 200 miles total!





Avid Traction bars $300 SHIPPED!
IN NEW condition!



PLX Wideband w/bosch sensor $210 Shipped

AEM 5 Bar map Sensor $75 shipped

AEM Boost solenoid $75 shipped

MSD Digital 7 Plus Prog (#75314 4 cyl apps only) $730 shipped
PRETTY MUCH BRAND NEW!!! Only used for 3 passes and 15 dyno pulls.
Will include Serial Cable with IOGear USB adapter cable.
And Wiring Harness if wanted, Shielded Air Craft Wiring was used and need to be grounded.
Shielded wiring reduces electric interference from the box and ECU.


MSD Dig 7 HVC II Coil $160 shipped
IN BRAND NEW CONDITION! Used for 3 passes and 15 dyno pulls!


Aeromotive Eliminator Pump $350 shipped
Dual summit filters with 100 michron inserts (before and after the pump) $100 for both



Golden Eagle Fuel Rail $100 shipped
with -10an & -6an fittings



Hasport Solid Mounts Powder coated black $300 shipped - Pending

Del Sol Dual Core Radiator w/slim fan $110 shipped


Full Racing Suit $400 shipped
Shroud Pants - SFI Cert 3-2A/5 - Large
Shroud Jacket - Double lined SFI Cert 3-2A/5 - Large
Simpson Shoes - Size 12
Shroud Gloves - SFI Spec 3.3/1 - Medium
Shroud Neck Brace - SFI Spec 3.3






Spinwerks Drag Wheels (slick below included) $600 shipped!
MT 24.5"x9" slicks
About 10 Passes. Wheels look BRAND NEW!!! Slicks have TONS of meat left!




VIS Invader Carbon Fiber Hood $350



1994 Acura Integra GSR Black Chassis: $3500!!! Local pickup only!

10 pt Cage, not cert yet but built for certification to 8.50's
Custom fitted MR Window net
Certified shroud 5 pt Harnesses (both drivers and passenger)
Shroud Parachute
Innes Cutoff Switch
Rolling on stock struts/springs
OMNI Camber Kit (front)
Powder coated wheel with Toyo Rears, Falkin Front tires
No fuel system!









Paypal address is SupraTT_T78@hotmail.com

Jason
801-879-4940.
I do have texting so. Text me if ya got questions.

 

ramhorn manifold for bseries
complete back purged manifold sch10, t3 flanged and accepts a tial 44mm wg. only used for mock up fits great and brand new never ran on my loss

650.00

top mount manifold b series.
off my street car is new and fully done ( no wg flange pictured accepts a 44mm tial). fully back purged sch10 t3 flanged


700.00
golden eagle b16/ls manifold w/ accufab 90mm tb with v band clamp attachment.
this is a ge intake manifold with a 90mm accufab tb. 90mm tb flanged already welded comes with everything, gaskets, v band, tps sensor, ge billet blk anodized polished f rail bored for domestic injectors, comes with -8 an fittings for quick and simple install. ported runners. everything is setup and no need to fabricate anything to make this work. throttle cable is a simple 99 Si or ls throttle cable already made. 1000.00 + into this manifold.
willing to part out 400.00 manifold, 80.00 rail w/o guage, 350.00 tb with vband.





760.00 takes it all


TURBO OIL FEED/EVAC KIT
-comes with everything you need for your turbo

$115.00 shipped.

Jacobs PRO Street Ignition box lil dusty but new and never installed.
i have used jacobs ignition systems on many other cars with no problems after 10 years of use. very reliable and great power.
blows the msd digital 6 out of the water and willing to part ways for dirt cheap. normally sells for over 480.00+ seen on summit and other sites
stats on the ignition box:

Brand: Jacobs Electronics
Product Line: Jacobs Digital Ignitions Pro-Street Kits
Part Type: Ignition Box and Coil Kits
Part Number: JAC-372546
Circuitry: Digital
Rev Limiter: Yes
Ignition Box Output: Capacitive discharge
CD Voltage Output to Coil: 535 V
Minimum Operating Voltage: 7.5 V
Maximum Operating Voltage: 18 V
Current Draw: 11 amps at 10,000 rpm
Spark Output (millijoules): 145 Millijoules


100.00 obo!!

FCS clutch line kit. this kit is for clutch master to slave. eliminates all the oem lines to the slave. looks really nice. comes with 2 fittings and ss line with clear jacket.


65.00

FCS brake line kit new in the bag with clips,bolts,washers,etc. lines comes with mounts and a clear jacket to cover the ss braided line. fits civic/integra, ek, da, em very nice. sells for 139.00 just removed it to take pictures.

90.00

1/4" d.o.t. air brake push lock vaccum / boost kits
everything you need to plum your turbo or vaccum lines. stainless steel fittings with high temp high impact d.o.t approved fittings and firestone d.o.t air brake lines.
plum your twin wastegates, boost solenoid, b.o.v, fpr, boost ref, and vacuum all in one package

$90.00 SHIPPED

6ft of fire sleeve in black and in silver. fits hose sizes -3 to -6

40.00

please pm me or if you need immediate response since this sale thread is first come first serve, please email me or aim

hellomrparks@yahoo.com
aim: jparks8832

 

Selling a used set of Bosh 1600 cc injectors. They work great and have 0 street miles cause they were used in my race car. Email me with questions at vrosario23@gmail.com for faster response since it goes to my phone.

$250 shipped

 

i have both items brand new in box selling for a freind he ran into financial problems new been mounted or plugged in

Aem engine management 30-104u which is the one with the wideband controller cheapest i could find it was little over 1400 1100 shipped



Turbonetics Gtk325 new never mounted good for 30 psi and 300-375 hp a very nice turbo for a smaller setup cheapest i could find this new for was 1465 1100 plus shipping

 

just another one of those gettin out of the game post
prices are obo and shipping is extrA
if using paypal + fees

-GM map sensor with pigtail $75

-AEM 1020 ecu 750 with complete obd2 uncut harness
works with:
96-98 Civic
96-99 Integra
96-01 Prelude
96-97 Accord
but if you use the harness u can put it into any car
$750 with harness


-26" slicks 26x10x15 and 26x4.5x15 skinnies mounted on some bogarts
$1500





-Turbo XS dual stage manual boost controller $200


-RC 1000cc $200


-AEM FUEL RAIL WITH AEM REGULATOR $175 (H-SERIES)


-New Fire Supression system $300


-PWR water to air intercooler3" in and out with heat exchanger12"x12"1.5" and fan $500




-H22 obx oil pan $100


-AEM wideband o2 cut harness(between the gauge and sensor harness) but could be soldered back $100


-1996 h22 fully built motor and trans $3500
ran fine before i pulled the motor no smoke no anything!
Motor:
Ferrea valves
Crower valvesprings and retainers
Crower Turbo profile cams
Darton sleeved & cryo-treated Block
Eagle H-beam 650 hp rods w/ ARP bolts
ARP head bolts
9:1 Endyn Weisco Rollerwave Pistons

Tranny & Drivetrain:
Cryo-treated all internals and rebuilt @ 75k (there were no issues, just wanted a fresh tranny for the extra power!)
Quaife LSD
Clutchmasters Stage 5 twin-plate clutch
gator axles





-crx race car rolling chassis. The chassis has over $8K worth of chromoly work done to include a chromoly straight rear axle.
The car will come on steelies. with the one piece front end and wheelie bars etc...

let me get more detailed with this car... it has a one piece front end, kirkey racing seat, wilwood hand brake, fuelcell , roll caged,aluminum dash and interior, battery cut off, removeable wheelie bar,rear straight axle,lexan all around, super light car!!! $2000







buy it all(parts and car) for $6500 and youve got yourself a fast car... all that its missing is a fuel pump and time
best way to get a hold of me is email
mrhuybui@gmail.com
thanks

 

The manifold it designed for T4 Divided housing but will also work with T4 On-center housing which is what I had in my car. Manifold is flanged for two Tial 38mm MV-S gates which are not included. Down pipe is 3in inlet flared to 4in. Inlet can be mated to most t4 turbo with vband outlets Precision/Garret vbands and I believe the bullseye t4 vbands also. Dumptube are setup to dump out the hood but could easily be modified to go dump under the car. Manifold just had some repair work done where the wg runner meets the collector, you can see it on the 3rd picture.

Looking to get $900obo for the complete setup plus shipping. PM for any questions






Vibrant 4in Race *NEW* $75