f/t f/s 1999 mr em1 great project car
Thread Starter
Honda-Tech Member
Joined: Oct 2008
Posts: 445
Likes: 0
From: Lexington,South Carolina, USA
i am putting up my 1999 mr em1 with a built b20vtec i need a more reliable car cause i drive an hour to get to school the car im looking for anything jus through me some offers
the car jus recently started acting up and im not sure wat it is.
b20 vtec (b20b4 block, gsr head)
low compression build for boost
cp pistions (8.5:1 cr)
manly rods
acl race bearings
arp hardware
exedy stage 1 clutch
i think some kinda flywheel, but not sure
walbro 255 in the tank
custom valve cover moon cut painted to match car
stock gsr cams
msd ignition with: msd cap, msd blaster coil, msd plug wires
aerospeed cam gears
abs intake manifold
full rev hard valve springs titanium retainers and valves
megan 4to1 header (cracking about 1" on 1 of the welds, jus needs a fresh bead burned in)
slimfan (10"-12" i believe, also, its wired in like stock, not rigged)
jvc cd player
autometer air/fuel -oil psi (a/f has power, but not hooked up)
skunk2 short shifter
black gsr leather fronts
stock rear si seats
interior is pretty clean, i give it about an 8 out of 10 or so, carpet could use a good cleaning, other than that its pretty minty
skunk2 springs with coil sleeves
i jus ordered a new header for it and it should be here within the next couple of days
the car would be an amazing project car i jus dont have the time and money to put into it due to college
and i have a turbo kit for it too ill throw in for a little cash or for the right car





the car jus recently started acting up and im not sure wat it is.
b20 vtec (b20b4 block, gsr head)
low compression build for boost
cp pistions (8.5:1 cr)
manly rods
acl race bearings
arp hardware
exedy stage 1 clutch
i think some kinda flywheel, but not sure
walbro 255 in the tank
custom valve cover moon cut painted to match car
stock gsr cams
msd ignition with: msd cap, msd blaster coil, msd plug wires
aerospeed cam gears
abs intake manifold
full rev hard valve springs titanium retainers and valves
megan 4to1 header (cracking about 1" on 1 of the welds, jus needs a fresh bead burned in)
slimfan (10"-12" i believe, also, its wired in like stock, not rigged)
jvc cd player
autometer air/fuel -oil psi (a/f has power, but not hooked up)
skunk2 short shifter
black gsr leather fronts
stock rear si seats
interior is pretty clean, i give it about an 8 out of 10 or so, carpet could use a good cleaning, other than that its pretty minty
skunk2 springs with coil sleeves
i jus ordered a new header for it and it should be here within the next couple of days
the car would be an amazing project car i jus dont have the time and money to put into it due to college
and i have a turbo kit for it too ill throw in for a little cash or for the right car





Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
GirlsWorkonHondas2
Vehicles for sale
26
Jan 21, 2009 08:39 PM
NA99CIVICSI
All Motor / Naturally Aspirated
14
Feb 6, 2004 09:35 PM
FS: GSR cam/gears, valve spings/retainers; Crane ignition/coil; MSD coil; GSR 4-1 header; 92-95 gaug
Smoothy
For Sale
17
Jan 2, 2004 06:18 PM



