96-00 Mugen intake system, Type R & Si
Thread Starter
Honda-Tech Member
Joined: May 2007
Posts: 693
Likes: 0
From: Pittsburgh, pa, U.S. and A
96-00 Mugen intake system, Type R & Si
*******<<<<<<<< LINK TO EBAY AUCTIONS >>>>>>>>>********
http://shop.ebay.com/merchant/matt94..._sopZ12?_rdc=1
This is the badest of the badest intake setups that money can buy! It uses a hand made fiberglass airbox. This system has 2 velocity stacks in it.... its just an incredible setup. It will produce better "useable" power than any other system.... which is much needed with any B series, especially B16's.
This unit is in excellent condition with very few scratches from installing... There NO cracks or major defects. The aluminum part that is exposed when installed has a small amount of corrosion on it, but could be easily polished up. Also it should be noted that 2 of the 6 screws are different and the felt gasket on the aluminum part could stand to be replaced (foam tape will work perfect).
***NOTE*** It was brought to my atention that there is a small metal bracket missing, that gets clamped around the velocity stack with a hose clamp, and connects to the strut tower. I dont have this bracket, my buddy who bought this system new, is looking for it, but Im not sure it will turn up... so I will drop the price from $550shipped to $525 shipped.
Part number: 17200-XGER-K0S0
It retails for $869 on http://www.kingmotorsports.com/category.aspx?cat=60
Asking $525 shipped! or $475 for local pick up.
http://shop.ebay.com/merchant/matt94..._sopZ12?_rdc=1
This is the badest of the badest intake setups that money can buy! It uses a hand made fiberglass airbox. This system has 2 velocity stacks in it.... its just an incredible setup. It will produce better "useable" power than any other system.... which is much needed with any B series, especially B16's.
This unit is in excellent condition with very few scratches from installing... There NO cracks or major defects. The aluminum part that is exposed when installed has a small amount of corrosion on it, but could be easily polished up. Also it should be noted that 2 of the 6 screws are different and the felt gasket on the aluminum part could stand to be replaced (foam tape will work perfect).
***NOTE*** It was brought to my atention that there is a small metal bracket missing, that gets clamped around the velocity stack with a hose clamp, and connects to the strut tower. I dont have this bracket, my buddy who bought this system new, is looking for it, but Im not sure it will turn up... so I will drop the price from $550shipped to $525 shipped.
Part number: 17200-XGER-K0S0
It retails for $869 on http://www.kingmotorsports.com/category.aspx?cat=60
Asking $525 shipped! or $475 for local pick up.
Last edited by matt94z; May 24, 2009 at 03:11 AM.
Trending Topics
Thread Starter
Honda-Tech Member
Joined: May 2007
Posts: 693
Likes: 0
From: Pittsburgh, pa, U.S. and A
Re: 96-00 Mugen intake system, Type R & Si
Bump deal fell through. I am in the market for a few items that I would accept on a partial trade:
-3" catback for 96-00 Coupe.
-DSM 450's
-P28 ECU
-Wahlbro 255 for 00 Civic
-and some other odds and ends for boost.
-3" catback for 96-00 Coupe.
-DSM 450's
-P28 ECU
-Wahlbro 255 for 00 Civic
-and some other odds and ends for boost.
Thread Starter
Honda-Tech Member
Joined: May 2007
Posts: 693
Likes: 0
From: Pittsburgh, pa, U.S. and A
Re: 96-00 Mugen intake system, Type R & Si
I def. noticed a loss in mid and top end loss when I removed this and put my stock airbox back on. If I dont get close to my asking price, I'll probably just hang onto it.