F/S: 1989 Honda Civic Si
I have a '89 Civic Si for sale, right now i have it posted on craigslist.com right now. The only difference with that posting is that the system is not included in the sale. And I finally remember the name of the axles, they are Raxles. If I don't sell with in the next month, I will most likely be parting out. If you have any questions just email me at japanationcivic@yahoo.com, I have email on my phone and i will most likely respond back in a short while. Thanks for anyone looking.
http://bgky.craigslist.org/cto/985871383.html
http://bgky.craigslist.org/cto/985871383.html
So sure enough as soon as I posted this someone flagged my craigslist posting so i am going to try to post it on here.
I have a 1989 Honda Civic Si with OBDO B16 swap. The body has about 140k miles and the engine has about 40k miles on it.
Engine:
B16A1/ YS1 tranny
New clutch (2K miles)
All new gasket
Spoon chipped PR3 (Vtec kicks on at 4500 instead of 5200)
Chikara 4-2-1 header
2.5" header back exhaust
New distributor
Avid mounts and shiftlinkage
5" tach (installed but not hooked up)
Type-R shifter
Actual swap axles good up to 350hp (not the piece together kind)
Exterior:
Carbon Fiber look a like Spoon mirrors
14" AR rims
Interior:
Stock
No rips in the seats at all. Showing a little flatness but not as much as i have seen in others.
The body does have some rust but I have been told that it wouldn't be hard at all to cut it out and weld in a new piece. I have been working on this project for a few years now and it's time to move on. Hate to sell but due to new house, baby and wife tired of money being tied up in it; I have to sell. The car pulls hard, will spin tires cruising in first gear at 2k rpm and then flooring it. My lost your gain, taking $3000 OBO. If you have any question or more pictures just email me and I will respond as soon as possible.
I have a 1989 Honda Civic Si with OBDO B16 swap. The body has about 140k miles and the engine has about 40k miles on it.
Engine:
B16A1/ YS1 tranny
New clutch (2K miles)
All new gasket
Spoon chipped PR3 (Vtec kicks on at 4500 instead of 5200)
Chikara 4-2-1 header
2.5" header back exhaust
New distributor
Avid mounts and shiftlinkage
5" tach (installed but not hooked up)
Type-R shifter
Actual swap axles good up to 350hp (not the piece together kind)
Exterior:
Carbon Fiber look a like Spoon mirrors
14" AR rims
Interior:
Stock
No rips in the seats at all. Showing a little flatness but not as much as i have seen in others.
The body does have some rust but I have been told that it wouldn't be hard at all to cut it out and weld in a new piece. I have been working on this project for a few years now and it's time to move on. Hate to sell but due to new house, baby and wife tired of money being tied up in it; I have to sell. The car pulls hard, will spin tires cruising in first gear at 2k rpm and then flooring it. My lost your gain, taking $3000 OBO. If you have any question or more pictures just email me and I will respond as soon as possible.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Proton698
Honda Civic (2006 - 2015)
9
Aug 16, 2009 08:31 AM
KLackeyImages
Vehicles for sale
12
Mar 1, 2005 09:38 AM




