Race ready 91 civic shell w/ everything you need!
Thread Starter
Joined: Oct 2002
Posts: 1,282
Likes: 0
From: Bay Area, CA, US
Race ready 91 civic shell w/ everything you need!
I am selling my 91 Civic hatch that was my race car but we blew the motor after 3 runs at the track. It only had a few dyno runs for tuning and 3 runs at the track after is was all together so the parts included are near new.
I am asking $1500 OBO for everything in the list below, everything. It has a clean title and I have the pink slip in hand.
For the most part, just buy a engine/tranny, plug everything in and fire it up!!!!!!!!!!!!!
NO PARTING AT THIS TIME!!!
It is a 91 civic hatch, primered black, inside and out including the door jams, under the hood, in the back etc.
It has a welded in 8 point roll cage from http://www.safedrives.com
It has a black 8 gallon fuel cell.
It is equiped with a Aeromotive A1000 fuel pump. It cost me over $300 from http://www.summitracing.com
It comes with a 40 micron inline fuel filter.
The fueling is plumbed with -8AN steel braided line for both supply and return.
Brand new Brembo brake discs/drums with Axis pads.
Comes with steelies wrapped in Pirelli tires.
I am throwing in 2 Nitto NT01 comp/drag radials with LOTS of meat left. Remember, only 3 runs.
It includes 2 yellow no name racing seats.
It will come with a pair of black 4 point racing harnesses from RCI.
I am throwing in a set of Raxles race axles that we ran on this car with a B series mtotor with a cable tranny. We picked up the Axles BRAND NEW made for the car and our set up.
I am throwing in a tac and shift light, from Autometer.
It comes with a pillar mount that will come with 3 gauges from Autometer, A/F ratio, oil pressure and water temp. The gauges come with all of the sensors needed.
I am throwing in a set of mounts to drop a B series in the car, the mounts are from Az Race, cost me $280. http://www.azrace.net
The car will include the upper and lower radiator hoses to run a B series in the car, made by Samco.
It comes with a harness to run a Vtec B series in the car, it was made by http://www.rywire.com
It comes with a Chrome programmed P28 ECU AND the jumper harness.
All picts car been seen here-
http://www.villagephotos.com/p...72800
I am asking $1500 OBO for everything in the list below, everything. It has a clean title and I have the pink slip in hand.
For the most part, just buy a engine/tranny, plug everything in and fire it up!!!!!!!!!!!!!
NO PARTING AT THIS TIME!!!
It is a 91 civic hatch, primered black, inside and out including the door jams, under the hood, in the back etc.
It has a welded in 8 point roll cage from http://www.safedrives.com
It has a black 8 gallon fuel cell.
It is equiped with a Aeromotive A1000 fuel pump. It cost me over $300 from http://www.summitracing.com
It comes with a 40 micron inline fuel filter.
The fueling is plumbed with -8AN steel braided line for both supply and return.
Brand new Brembo brake discs/drums with Axis pads.
Comes with steelies wrapped in Pirelli tires.
I am throwing in 2 Nitto NT01 comp/drag radials with LOTS of meat left. Remember, only 3 runs.
It includes 2 yellow no name racing seats.
It will come with a pair of black 4 point racing harnesses from RCI.
I am throwing in a set of Raxles race axles that we ran on this car with a B series mtotor with a cable tranny. We picked up the Axles BRAND NEW made for the car and our set up.
I am throwing in a tac and shift light, from Autometer.
It comes with a pillar mount that will come with 3 gauges from Autometer, A/F ratio, oil pressure and water temp. The gauges come with all of the sensors needed.
I am throwing in a set of mounts to drop a B series in the car, the mounts are from Az Race, cost me $280. http://www.azrace.net
The car will include the upper and lower radiator hoses to run a B series in the car, made by Samco.
It comes with a harness to run a Vtec B series in the car, it was made by http://www.rywire.com
It comes with a Chrome programmed P28 ECU AND the jumper harness.
All picts car been seen here-
http://www.villagephotos.com/p...72800
Trending Topics
Thread Starter
Joined: Oct 2002
Posts: 1,282
Likes: 0
From: Bay Area, CA, US
I was diggin through my stuff today and found the brand new starter I was using when I had a motor in the car and also the altenator that I used. The altenator has a lightened pulley. I can throw these in.
Thread Starter
Joined: Oct 2002
Posts: 1,282
Likes: 0
From: Bay Area, CA, US
Re: Race ready 91 civic shell w/ everything you need! (k20_typeR_EG)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by k20_typeR_EG »</TD></TR><TR><TD CLASS="quote">very cheap to bad i dont like ef or i would pick this up... 
</TD></TR></TABLE>
I know it's REAL cheap. I know I could part out and make more than I am asking. I am debating as to whether part it out or just put it back together. I already have a real tough motor I can drop in. Would just need a few things here and there.
</TD></TR></TABLE>I know it's REAL cheap. I know I could part out and make more than I am asking. I am debating as to whether part it out or just put it back together. I already have a real tough motor I can drop in. Would just need a few things here and there.
Thread
Thread Starter
Forum
Replies
Last Post
NUISANCE
Northern California (Sales)
31
Nov 13, 2008 08:11 PM
NUISANCE
Vehicles for sale
20
Sep 29, 2008 12:03 AM