Just what it says.

Thanks.

 

Thats a very broad question to ask man.

That would depend on the level of HP the car has and that would include tons of setups.

Are you looking for stock block 1.8l numbers?

 

with my 232whp motor and 4.7 trans, i was trapping 112-113 with 15" slicks and 9000 rpm rev limiter.

hope that helps.

what exactly are you looking to do with this info?

 

Im just hanging with some friends and thought I would ask this on honda tech. Please post mods and hp numbers. Thanks for the info above.

 

built B series. not getting into the specs. it was 86x89mm with an unported head though.

 

you'd probably get more answers in the type R forum

 

100% no. haha. they dont drag race. they hate when i post drag racing stuff there.. haah

 

Cool 11.9 all motor. How much money is in that motor? What did you run with just bolt ons?

 

i never raced any vtec motor with just bolt ons.

but i spent a lot of money. you can get into a built head and run 12s on slicks for about 3-4000 after tuning and good bolt ons.

 

cool i just spent over 2k on my bottem end.

 

what's the point in this thread?

this is going no where

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by LDS &raquo;</TD></TR><TR><TD CLASS="quote">How much money is in that motor?</TD></TR></TABLE>

LOL

Anyways, IBTL, just IM him Fran. haha.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by pgpbubble &raquo;</TD></TR><TR><TD CLASS="quote">what's the point in this thread?

this is going no where</TD></TR></TABLE>

I like to talk about cars and my wife doesnt want to hear about my type-r all the time and all the little things i do to it. Im sorry if theres no point, but to me this is like talking to friends about Type-Rs.

 

I am trying to get the sweet spot with my slicks but it is very fustrating. I have a JDM Civic Type R with a few boltons making 193/132 and doing 13.6 @100mph w/2.065 60ft. I run a b16b tranny with an Mfactory 4.7 final drive, and use 22x8x15 MT slicks on civic type r rims. I tried tire pressure at 10psi (cold) and am working my way down to 8psi, launching at 8300 rpms. I could only get a 2.0 60ft, but was cutting consistant 1.9's with my old ITR with less power. Please tell me according to my HP and MPH, what I should expect with a 1.8 or better 60ft? Oh the car weighs 2658 w/driver

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Teamdiesel &raquo;</TD></TR><TR><TD CLASS="quote">I am trying to get the sweet spot with my slicks but it is very fustrating. I have a JDM Civic Type R with a few boltons making 193/132 and doing 13.6 @100mph w/2.065 60ft. I run a b16b tranny with an Mfactory 4.7 final drive, and use 22x8x15 MT slicks on civic type r rims. I tried tire pressure at 10psi (cold) and am working my way down to 8psi, launching at 8300 rpms. I could only get a 2.0 60ft, but was cutting consistant 1.9's with my old ITR with less power. Please tell me according to my HP and MPH, what I should expect with a 1.8 or better 60ft? Oh the car weighs 2658 w/driver </TD></TR></TABLE>

Well if you take 2/10ths off your 60ft its atleast 2/10ths off your 1/4 providing the rest of your run has no variables.

 

All motor Type R.... check sig

 

91 octane? What ignition timing are you running? Stock 16? or less?