1991 honda civic hatch with built ls swap 3500 obo washington !!!!!!
i have a 1991 honda civic hatch with a 94 civic front end conversion for sale i am asking 3500.00$$ obo,
this car comes with a pretty well built 1.8 b18b1 ls integra engine
MODS INCLUDE:
engine/ b18b1 out of a 96 integra with 86k miles on the engine origanally
pulled apart and rebuilt everything with the following
*delta cam 272duration cams
*full port and polish with 3 angle valve job
* type-r valves, springs and retainers,
*intake plenuim hollowed out for more air
type-r throttle body
brand new dizzy and taylor spiro pro wires 8.5 mm and ngk iridium plugs
gsr pistons with shot peened rods
gsr fuel pump and oil pan and pump and pick up tube
micropollished crankshaft
rod bearings and main bearings dirrect from hinshaws acura all color matched
and every single gasket, o-ring seal all replaced
act 6 puck unsprung clutch/2600 lb pressuer plate
type-r flywheel shaved down to 11.8 lbs
brand new water pump and radiator with hoses
car comes with
oil pressuer gauge
a/f ratio gauge
tach mounted ou apiller
and corbeau racing seat
-------------------------------------------
i dont have interior pics as of yet but if you wish i can get some with in the next couple days
I have well over 4,000.00 dollars in parts stuff building this engine
ai hate to see it go but i need to pay off some fines so i am asking 3500 obo
sorry no trades cause i need the cash
i ran it at bremerton raceway yesterday and ran a 14.8 spining into third.
next time i go if it dont sell by then i will be using slicks and see how much faster it goes
thanks for looking
if you have any questions feel free to call
360 621 6161 i dont get a chance to check my email that often but here it is anyways
turbozcteg@yahoo.com







this car comes with a pretty well built 1.8 b18b1 ls integra engine
MODS INCLUDE:
engine/ b18b1 out of a 96 integra with 86k miles on the engine origanally
pulled apart and rebuilt everything with the following
*delta cam 272duration cams
*full port and polish with 3 angle valve job
* type-r valves, springs and retainers,
*intake plenuim hollowed out for more air
type-r throttle body
brand new dizzy and taylor spiro pro wires 8.5 mm and ngk iridium plugs
gsr pistons with shot peened rods
gsr fuel pump and oil pan and pump and pick up tube
micropollished crankshaft
rod bearings and main bearings dirrect from hinshaws acura all color matched
and every single gasket, o-ring seal all replaced
act 6 puck unsprung clutch/2600 lb pressuer plate
type-r flywheel shaved down to 11.8 lbs
brand new water pump and radiator with hoses
car comes with
oil pressuer gauge
a/f ratio gauge
tach mounted ou apiller
and corbeau racing seat
-------------------------------------------
i dont have interior pics as of yet but if you wish i can get some with in the next couple days
I have well over 4,000.00 dollars in parts stuff building this engine
ai hate to see it go but i need to pay off some fines so i am asking 3500 obo
sorry no trades cause i need the cash
i ran it at bremerton raceway yesterday and ran a 14.8 spining into third.
next time i go if it dont sell by then i will be using slicks and see how much faster it goes
thanks for looking
if you have any questions feel free to call
360 621 6161 i dont get a chance to check my email that often but here it is anyways
turbozcteg@yahoo.com







Thread
Thread Starter
Forum
Replies
Last Post
92integraVTECgsr
Southeast (Sales)
14
Aug 29, 2008 05:46 AM



