Hey guys, heres the story, we built a car for my buddy & dumped crap loads of cash into this setup, but now that it's completed & what not, he is getting married & needs the cash to pay off his wedding. We've done nothing but start the car up & drove it around the block. We have finally decided that parting out his engine is the only way he can come up with the cash that he needs. These prices are going to be pretty firm so don't be low ballin me. I can provide pictures for everything and will probly post them all up this week regardless if asked for or not. The list is as follows.


b18a SLEEVED Block w/Internals $1500
- Golden Eagle Sleeved
- Knifed crank (import builders)
- Wiseco Pistons (ceramic coated)
- Forged Rods (Import Builders spec)
- new Water pump
- new Type-r oil pump
- new bearings & seals
*Block was assembled by import builders and the reciept can be provided as proof.


SOLD
GSR Head (99) $1000
- New GSR cams
- Import Builders valve train (safly rev to 10k)
- Dark Star adjustable cam gears (5 bolt)
- new lifters
- new valve stem seals
- new valve guides
- Import Builders port & polish job
- 3 angle valve job
- obd1 Distributor
- includes valve cover
*Head assembled by import builders and the reciept can be provided as proof if needed.

SOLD
T3/T4 TURBO (MasterPower, quality, not junk)

SOLD
OBX RamHorn Manifold (good welds) with 40mm Tial wastegate $475

ARP head studs (torqued once) $75
Skunk2 Intake manifold (gsr) $200
Spearco Intercooler $175
Hondata Intake Manifold Gasket $obo
PLX Wideband /w digital readout $250

More stuff will be comming, and i will remove the items from the list or mark them as they are sold. We prefer paypal, PM for detials.

Modified by Running925 at 11:28 PM 1/19/2007


Modified by Running925 at 1:46 PM 1/21/2007


Modified by Running925 at 6:20 AM 1/29/2007


Modified by Running925 at 6:20 AM 1/29/2007


Modified by Running925 at 6:21 AM 1/29/2007

 

morning bump

 

at work bump

 

late night bump

 

morning bump

 

c'mon guys buy this stuff up, i'm gonna have to list it all on ebay very soon!

end of the work day bump

 

gimme a call....615-491-1656...i dont sleep till late

 

pmed

 

Heres some pictures, we pulled the head last night because some pictures of the top of the block were requested.


You can see how clean this was!


Skunk2 Intake Manifold comes with GSR throttle body and all sensors, also includes Hondata gasket.


Side View


This is a pic of how it looked when it was assembled:


This picture shows that once the head was pulled, there wasn't muck carbon on the Ceramic Coated Pistons. One good swipe of the shop rag across the top of the piston & it was clean again! This engine was ran for less than a mile! It was installed, checked for leaks, went around the block once & put back in the garage.

$1500 Golden Eagle Sleeved / Wiseco Ceramic Coated Pistons / IBspec Rods / ACL Bearings / New TypeR Oil Pump / New Waterpump / All sensors / Tensioners / Tapped Oil Pan / ect.

 

how much for the complete turbo set up? it will fit a gsr engine right? lemme know

 

PM me with what all your going to want and i'll be able to give you a more accurate price.

 

Here is another bump with more pix of different parts

AEM Fuel Rail / AEM Adjustable Fuel Pressure Regulator / Liquid filled gauge



Nology Spark Plug Wires:

 

what r the rods rated at?...or whats the limit it has been pused too?.

 

They are IBspec (Import Builders) rods, and they rate them at 600+ hp

You can find more information on them at ImportBuilders.com
Jeff builds all his own equiptment & is very reputable

 

whats there number?...i am really interested in the block..i just wanna ask them some ?'s bout the rods

 

we've always spoke to them via e-mail from their website. They are in CA, we're in Ohio.

 

What is the compresion,bore?

 

.

 

will u sell intake manifold....

 

whats the lowest priced picked up for the block? Im in indy

 

Compression on the block is 8.5:1
Bore is 81mm

Yes i will sell the intake manifold seperatly, make me a reasonable offer.

1500 picked up is my lowest price for the block. To much money invested to let it go any cheaper. It's literaly brand new and never seen boost. It ran once and thats it, refer to origional post for more info.

feel free to ask any other questions that you may have

btw, the head and the turbo are now sold

 

I will keep an eye out on this thread. I have to pay off few bills this week. If its still here by this weekend coming up i might be interested in coming and getting it.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by indy90turbocrx &raquo;</TD></TR><TR><TD CLASS="quote">I will keep an eye out on this thread. I have to pay off few bills this week. If its still here by this weekend coming up i might be interested in coming and getting it.</TD></TR></TABLE>

sounds good.. just lemme know.

 

I believe I'm going to buy this man. If you get someone wanting to come get it let me know. I will paypal you the money. I need to see if my buddy is free this up coming weekend to come pick it up. If you could email me at turbohappy@aol.com. Send me your adress and phone number I can get in contact with.

Thanks

 

I just sent you my contact information via e-mail