SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit
Thread Starter
Honda-Tech Member
Joined: Jun 2004
Posts: 1,153
Likes: 0
From: Louisville, KY, USA
SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit
Here's what I have for sale:
-550cc RX7 Saturated (High Impedance) Fuel Injectors with clips $125 **SOLD**
-Greddy/Trust D Series Cast Turbo Manifold Tapped for a T3 $175
-T3 52 Trim Turbo from a Volvo. Has some very slight shaft play, but that should be minimized when some oil is run through it. No in and out play. Comes with internal wastegate flapper assembly and actuator. It has also been machined to fit a standard T3 flange without any problems. Manifold and turbo would be a good combo. $175 **SOLD**
-2" Polished intercooler piping. Some dings but should be fine. Comes with a 1g DSM BOV (I believe it has been crushed, but not sure) and some older couplers and clamps (may need to be replaced, but probably useable). $175 **SOLD**
-Front Mount Intercooler 23.5 x 6 x 3.5" core with 2" inlet and outlet. A couple of bent fins, but nothing major. $175 **SOLD**
-New ARP Headstuds for D series engines $80 **Sold locally**
-New (but opened) 96-00(??) Block gasket kit $25
-New (but opened) Tuner Toys/Stealthmode Performance Oil Line Kit $85 **SOLD**
-Single cam Honda OEM catalytic conveter $20
-96-00 Civic Dual Gauge Pod Bezel $25 **Sold locally**
-2 Goodyear Victor V R430 Road Racing Slicks. Really good tread still left on them. Unmounted. $150
-2 20x6x14" Mickey Thompson Drag slicks. Again, really good tread on these. One of the sidewalls blew out, so these have tubes inside of them. I have ran them as low as 10.5 psi and had no problems with them. I would recommend running a little higher pressure, though. Sticky as hell. Mounted on VW rims. $150
-T3 turbo oil inlet flange $15 **SOLD**
-2.5" Flex pipe $10 **Sold to joshb_**
-92-00 Civic Tanabe Super Down Precedo Springs $65 **SOLD**
-95 Prelude A/T Resistor Box $25
-T25 Hot Side $15
Modified by Mistamike17 at 8:46 AM 6/23/2006
-550cc RX7 Saturated (High Impedance) Fuel Injectors with clips $125 **SOLD**
-Greddy/Trust D Series Cast Turbo Manifold Tapped for a T3 $175
-T3 52 Trim Turbo from a Volvo. Has some very slight shaft play, but that should be minimized when some oil is run through it. No in and out play. Comes with internal wastegate flapper assembly and actuator. It has also been machined to fit a standard T3 flange without any problems. Manifold and turbo would be a good combo. $175 **SOLD**
-2" Polished intercooler piping. Some dings but should be fine. Comes with a 1g DSM BOV (I believe it has been crushed, but not sure) and some older couplers and clamps (may need to be replaced, but probably useable). $175 **SOLD**
-Front Mount Intercooler 23.5 x 6 x 3.5" core with 2" inlet and outlet. A couple of bent fins, but nothing major. $175 **SOLD**
-New ARP Headstuds for D series engines $80 **Sold locally**
-New (but opened) 96-00(??) Block gasket kit $25
-New (but opened) Tuner Toys/Stealthmode Performance Oil Line Kit $85 **SOLD**
-Single cam Honda OEM catalytic conveter $20
-96-00 Civic Dual Gauge Pod Bezel $25 **Sold locally**
-2 Goodyear Victor V R430 Road Racing Slicks. Really good tread still left on them. Unmounted. $150
-2 20x6x14" Mickey Thompson Drag slicks. Again, really good tread on these. One of the sidewalls blew out, so these have tubes inside of them. I have ran them as low as 10.5 psi and had no problems with them. I would recommend running a little higher pressure, though. Sticky as hell. Mounted on VW rims. $150
-T3 turbo oil inlet flange $15 **SOLD**
-2.5" Flex pipe $10 **Sold to joshb_**
-92-00 Civic Tanabe Super Down Precedo Springs $65 **SOLD**
-95 Prelude A/T Resistor Box $25
-T25 Hot Side $15
Modified by Mistamike17 at 8:46 AM 6/23/2006
Thread Starter
Honda-Tech Member
Joined: Jun 2004
Posts: 1,153
Likes: 0
From: Louisville, KY, USA
Re: SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit (Mistamike17)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Mistamike17 »</TD></TR><TR><TD CLASS="quote">PMs replied.</TD></TR></TABLE>
Trending Topics
B*a*n*n*e*d
Joined: Nov 2004
Posts: 1,418
Likes: 0
From: Wilmington, NC, U.S.A
Re: SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit (Mistamike17)
nice boost controller 
may know some people interested in these parts... I'll get back to ya.
may know some people interested in these parts... I'll get back to ya.
Thread Starter
Honda-Tech Member
Joined: Jun 2004
Posts: 1,153
Likes: 0
From: Louisville, KY, USA
Re: SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit (ejmotorfiend)
Probably 2+ inches. It really depends on the application. Heavier car will be lowered more than a lighter car.
Honda-Tech Member
Joined: Jul 2002
Posts: 4,681
Likes: 2
From: Columbia, SC, USA
Re: SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit (Mistamike17)
bump....i know some people, who know some people, who know some people that might be interested.
Honda-Tech Member
Joined: Sep 2004
Posts: 1,555
Likes: 0
From: Windchestertonfieldville, NJ, USA
Re: SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit (Mistamike17)
...so is the oil line kit sold or not?? i need one BAD, cuz my last turbo had the inlet flange WELDED in when i bought the kit... 
so i need the flange... GOT ONE... then i find out it doesnt fit the oil line i have.. too small. and i dont know how to find out what size the line is...
and the damn fitting in the back of the block SUCKS, it ***** up the threads so that you cant run the stock sensor back in if goin back to NA... and the funny thing is... it threaded in VERY smoothly...
let me know
so i need the flange... GOT ONE... then i find out it doesnt fit the oil line i have.. too small. and i dont know how to find out what size the line is...
and the damn fitting in the back of the block SUCKS, it ***** up the threads so that you cant run the stock sensor back in if goin back to NA... and the funny thing is... it threaded in VERY smoothly...
let me know
Thread Starter
Honda-Tech Member
Joined: Jun 2004
Posts: 1,153
Likes: 0
From: Louisville, KY, USA
Re: SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit (HatchEh2)
Dude, read the thread. It's been three months since I last bumped this and the oil line kit says **SOLD** next to it.
Honda-Tech Member
Joined: Sep 2004
Posts: 1,555
Likes: 0
From: Windchestertonfieldville, NJ, USA
Re: SOHC D16 Turbo Stuff, injectors, intercooler, piping, BOV, MBC, oil line kit (Mistamike17)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Mistamike17 »</TD></TR><TR><TD CLASS="quote">Nevermind... oil line kit not sold.</TD></TR></TABLE>
i did... and didnt see anything after that... so i was just asking.
i did... and didnt see anything after that... so i was just asking.
Thread
Thread Starter
Forum
Replies
Last Post
The Mista Mike
Classifieds: Forced Induction
45
Mar 26, 2006 07:28 AM
hifi_civic
Southern California (Sales)
1
Jul 24, 2005 05:27 AM
dtmwerks.com
Classifieds: Forced Induction
1
Feb 3, 2005 07:36 PM