I want mine like this.

 

i like it

 

clean drop

 

that what mine looks like when i lower it all the way down. gotta love B&G

 

here's another EF with 3.25" drop on sprint "extreme" springs.

 

mine looks the same, I have 205/50's tucked on all four corners with OMNI coilovers.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by ammob16 &raquo;</TD></TR><TR><TD CLASS="quote">mine looks the same, I have 205/50's tucked on all four corners with OMNI coilovers.</TD></TR></TABLE>

are you sure ? Omnis dont go that low..
unless you have the sleeve coilovers..
The full coilovers dont go that low...
I have them..

 

for some reason mine do, I was quite suprised myself. I set the preload to spec and everything. I need to raise it though, its a bit bouncy, but it looks hella good.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by ammob16 &raquo;</TD></TR><TR><TD CLASS="quote">for some reason mine do, I was quite suprised myself. I set the preload to spec and everything. I need to raise it though, its a bit bouncy, but it looks hella good. </TD></TR></TABLE>
HMM.. Lemme see a pic please !!!!!!!!!!!!!!!!!!!!!

 

let me see what I can do, it may take a few minutes.

 

nice drops

 

if this works, I know its a horrible picture.


Modified by ammob16 at 10:53 PM 12/31/2005

 

B&G's with a whole lot of dump left. gunna dump em tomorrow and take better pics. night pics suck and so does my exterior

 

that second red hatch looks like one here in vegas and this belongs in the appearence forum

 

isnt that civic with the Si's a vegas car? i think i seen it around..that first hatch is fkin slammed!

 

yea thats what i thought also i think ive seen it at the track a few times

 

Cleaness

 

nice what kinda wheels are those?

 

Can't slide my fingers between my tires and wheelwell on my 91 sedan on 1.75" springs and 16" wheels with 205/45 ZR16s.

I like that a LOT... and no scrapes at ANY time.

 

i like a dumped ef but its not practical for ****. I already scrape so many places in town (that i dont even drive to anymore) on a 2.5 inch drop, not to mention having a jdm 4-1 that hangs even lower. 3.25" sounds more like something for a show car..

 

Neuspeed race springs, 205/45/16 wheels

 

sorry to ***** the thread but i have a buddy that has a eg that tucks the whole tire on 13's

 

I'm rebuilding my EF. It's been a 3 year project so far and $40,000 dollars CDN.
I'll post up a whole project post later.

I just installed the suspension. I'm using TEIN SS coilovers with the pillow-ball upper mounts. I did the 5-bolt rear already but I'm still working on the fronts so don't mind the nastiness in the front.

This drop is with the coilovers all the way down front and rear. I have the block in with tranny but no head just to lay everything out and start running fuel lines, etc. Temp motor.





Here is the picture of the rear suspension setup. Function-7 lca's, TEIN, 5-bolt 'R' setup with powerslot rotors and ebc green pads.

 

Heres mine with my ground control coilover sleves, with Tokico Blues.




Heres a newer pic on 17's

 

A bit off topic, Im not too big on the hatch's but that green one looks amazing!