welp, im swapping putting a built b18b into my car, so im done with the SOHC motor. Its a d16z6, and its from my 95 civic ex. it has 77k on it and is in excellent shape. The compression is 180 on every cylinder. the tranny doesnt grind and im leaving my clutch and machined flywheel in it, i dont need them. the clutch is good for 300ft/lbs and it grabs very well.it will be complete, from oil pan to valve cover (which was also powdercoated aem blue) if u have questions just ask right here in the thread so everyone can see them. ill include the axels too as i don t need um. ill have up pics as well in a few days
im looking to get 650 for the motor complete.
thanx for looking and bump it on up if u look
i also have a d16z6 block. its in good shape, could use a hone job. 50 obo
b18b obd1 wiring harness. excellent shape. 70 shipped obo
as for the turbo kit. it will include a 6in fmic in great shape, piping, turbo xs rfl bov, all clamps and couplers, garrett t3 turbo, 60 trim, 450 high imp injectors, stainless short tubular manifold, 3in->2.5in downpipe, oil lines. all for 1000 plus shipping. its all in excellent shape the turbo has very lil haft play. the setup held 10 psi strong and i had no complaints.
i am willing to travel or meet half way, but it will be at drivers expense. i honstly wouldnt mind a 3hr drive as long as im compensated for gas money.





Modified by raiden571 at 8:46 PM 1/9/2006


Modified by raiden571 at 8:59 PM 1/9/2006

 

remember folks obo. the turbo stuff is pending as of now...i may be selling the piping as well, havent decided yet

 

i have been swimming to okinawa to meet a hot asian woman to play with my pepe

 

welp, im swapping putting a built b18b into my car, so im done with the SOHC motor. Its a d16z6, and its from my 95 civic ex. it has 77k on it and is in excellent shape. The compression is 180 on every cylinder. the tranny doesnt grind and im leaving my clutch and machined flywheel in it, i dont need them. the clutch is good for 300ft/lbs and it grabs very well. im also leaving my 450's in it too and u dont need a resisto box. it will be complete, from oil pan to valve cover (which was also powdercoated aem blue) if u have questions just ask right here in the thread so everyone can see them. ill include the axels too as i don t need um. ill have up pics as well in a few days
now, i also have a turbo shorty manifold, a t3 turbo, oil lines and a 6in intercooler as well. id like to sell it all at once if possible. its all still in the car as i dont wanna tear it out until i have a deffinit buyer. taking it all out can be done in a few hours. Running925 can vouch for me and the motor to be in stout condition.
im looking to get 650 for the motor complete. the turbo parts i will make a deal on if u buy it all at once, other wise, ill go from there.

will u include ecu and wiring harness?
if so how much for all that?
with turbo stuff.
e-mail me or get at me on aim : SiDriver148 and then @hotmail for e-mail.

 

welp. the turbo setup is pretty much sold unless u wanna pay more then 650 for that.
the swap i do not have the ecu or the harness for it. it will have the axels, motor oil pan to valve cover, 450 injectors, stock injectors will b e included, tranny, clutch specialties clutch that is rated to 300 ft/lbs, the flywheel has been machined. the compression tests 180 across the board. i change the oil about every 3k but never over 4k. i have had the car for about 15k and i got it from an old lady who had it serviced at honda since she bought it.

 

You gonna sell the piping?

 

if i do the bov will be with it. i dotn wana be stuck with my bov with out the flange. i would probably due 200 plus shipping. thats with couplers, the hose clamps, piping and the bov.

 

What was this piping in and how much could you do picked up? I live in ohio too

 

the piping was in a 95 civic with the sohc, and was running a 31in ic. the bumper needed minimal cutting and if u are more patient then i am and took your time tinkering, you could have probably trimmed even less then i did. i retained all my grill in the front and sides of the bumper, but i had to cut the back out of the grill and mini grill.
200 picked up and ill buy a pizza and we'll hang out for a bit

 

bump cause its pay day
rods sold
turbo stuff is pending

 

all turbo stuff is back up. origin al buyer cant come through!!! BUY MY STUFF SO I CAN BUILD MY MOTOR!!!
remember, local pick up is prefered, but shipping is fine by my but its at your expense

 

would you sell just the turbo manifold?

 

I am still interested in the piping and what not just trying to sell some of my stuff.

 

id reallr rather sell everything together, but ill take offers on them and consider it.
thats cool man with the piping. i gotta keep it up for sale though until i have proof you really want it

 

if the sohc vtec motor still for sale and would you take 600 for it picked up

 

pm me and well discuss it. and yes, i still have it
i will most likely ake 600 unless someone has a better offer.
everything else except the rods are up for grabs!!!


Modified by raiden571 at 1:18 PM 12/22/2005

 

ecu sold

 

how much for the manifold and turbo?

 

pms replied.

 

up for me and the woman going out to dinner

 

up for me working a 12 our day tomorrow so i can have the whole weekend off.
come on folks, i need to get my b done!!!!!!!!!!!!!!!

 

pm me with best price for turbo kit and pipes, what were you using for fuel mgmt

 

you have been pmed. uberdata

 

open to all offers

 

more pics of the goods, the rest will be off soon for more pics