Hello EG forum, its been a while!

Anyways, Bense and myself are preparing ourselves for a sohc build that will turn heads. We are running a y5 head with around 12.5:1 compression in a d16a6 block, and with the y5 head we can run a super aggressive cam, just no piston to valve contact . What is the most aggressive cam that is mass produced? Thanks!!!

 

who offers regrinds?

 

delta has regrinds

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by haveaniceday &raquo;</TD></TR><TR><TD CLASS="quote">delta has regrinds</TD></TR></TABLE>

would you happen to know the cost of this?

 

About $100 shipped

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by crixzc &raquo;</TD></TR><TR><TD CLASS="quote">About $100 shipped</TD></TR></TABLE>

wow, that's it?

 

I believe Crower has a Nice cam for the Single Slamer

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by JDMlyfestyle &raquo;</TD></TR><TR><TD CLASS="quote">I believe Crower has a Nice cam for the Single Slamer</TD></TR></TABLE>

nobody offers cams for the d16y5 (VTEC-E) head, so i'd have to get a custom regrind

 

Im sure crower has the proper machinery to make you a nice cam..lol

 

ZEX Cam

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by blaster834 &raquo;</TD></TR><TR><TD CLASS="quote">ZEX Cam</TD></TR></TABLE>

not available for a d16y5

 

whats the most agressive stock cam for a d-series?

srry for stealing the thread


Modified by 1993civicex at 10:50 PM 11/28/2005

 

Also, Delta doesn't regrind VTEC cams.

 

might try Web Cams for a regrind. they do hard welds and regrinding.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Ace0246 &raquo;</TD></TR><TR><TD CLASS="quote">might try Web Cams for a regrind. they do hard welds and regrinding.</TD></TR></TABLE>contact #?

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 1993civicex &raquo;</TD></TR><TR><TD CLASS="quote">whats the most agressive stock cam for a d-series?

srry for stealing the thread </TD></TR></TABLE>

the lobes on the d16y5 vtec-e are the largest as far as i know

and the d16a6 is pretty aggressive, but it wont' go into d16y7's

 

anyone else?

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 1993civicex &raquo;</TD></TR><TR><TD CLASS="quote">whats the most agressive stock cam for a d-series?

srry for stealing the thread


Modified by 1993civicex at 10:50 PM 11/28/2005</TD></TR></TABLE>
yeah.. i'm actually curious about that too...

 

you could check w/ gude, might take them awhile, and customer service isnt the greatest, but there actual tech department is pretty good.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Split Image Prez &raquo;</TD></TR><TR><TD CLASS="quote">
yeah.. i'm actually curious about that too...</TD></TR></TABLE>

You brought this thread up just to say that?

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Bense &raquo;</TD></TR><TR><TD CLASS="quote">

You brought this thread up just to say that?</TD></TR></TABLE> LOL yeah, I wasn't paying attention to the date or where I was even searching... LOL