Well there is not much to say except thanks for the rims and tires!!!
I washed the worst one and it could use a little more elbow grease but should make a full recovery

And then helped by holding the flashlight so he could change the springs in his caR for the Summit point event coming up this weekend

Here are the pics.

 

Nice.
that R looks to have some battlescars on it, for puttin the caR to use

 

Kosei

 

And here I thought Dave was just a pretty boy who had other people work on his car for him....

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by B18C5_EK &raquo;</TD></TR><TR><TD CLASS="quote">Nice.
that R looks to have some battlescars on it, for puttin the caR to use</TD></TR></TABLE>

Yes, scars from
1. A garage door opener falling on the car in 2001. Note to Sears installation guy... corner bead is NOT structural steel !!
2. Driver side front fender...Phil of Phil's tire service Turn 1 Summit Point.
3. Driver side front fender, Driver door, Driver rear 1/4 panel, Driver rear bumper... Curpier of Curpier Motorsports, Turn 1 Summit Point
4. Bent radiator support...Turn 1 Summit Point gravel PIT (Tow strap and telephone poll straighten things up nicely )

hmmmm there seems to be a theme... Turn 1 Summit Point...

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Backmarker &raquo;</TD></TR><TR><TD CLASS="quote">And here I thought Dave was just a pretty boy who had other people work on his car for him....</TD></TR></TABLE>

No, I am usually not ALLOWED to work on my car... I kind of skip a few steps here and there, and things get bent...sorry Aaron

Actually, I am ok with a wrench. I used to work on my race bicycle (Kestrel 200sci) and freestyle BMX bike years ago. I have installed most small things on my car (suspension, interior stuff, oil cooler, etc.). Big stuff (clutch, anything electrical) I leave for those who know what they are doing.

 

 

what rims are those? And good luck with the race

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by boostngsr &raquo;</TD></TR><TR><TD CLASS="quote">what rims are those? And good luck with the race </TD></TR></TABLE>

Reading is fundamental

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by ebelp &raquo;</TD></TR><TR><TD CLASS="quote">Kosei </TD></TR></TABLE>

Kosei K1 = :bling:

 

I sold Kosei's K1's to Bbasso. I have four sets and didn't need this fourth set.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by davidnyc &raquo;</TD></TR><TR><TD CLASS="quote">I sold Kosei's K1's to Bbasso. I have four sets and didn't need this fourth set.</TD></TR></TABLE>

Got any 4 luggers laying around?

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Alexander &raquo;</TD></TR><TR><TD CLASS="quote">

Got any 4 luggers laying around? </TD></TR></TABLE>


Nope, I am not a retail store, just a poor racer. well... poor in money.... rich in fun

 

does this mean i get my 12k spring?

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Dan GSR &raquo;</TD></TR><TR><TD CLASS="quote">

does this mean i get my 12k spring?</TD></TR></TABLE>

Yes, you finally get the 12K springs. (I am not sure what deal you had with Marc, however you can pick them up whenever... either late tonight or tomorrow)

Anyone want to buy a set of 10K springs? (8", 2.5"ID)

My new setup (800lb/14K F, 950lb/17K R)

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by davidnyc &raquo;</TD></TR><TR><TD CLASS="quote">No, I am usually not ALLOWED to work on my car... I kind of skip a few steps here and there, and things get bent...sorry Aaron

Actually, I am ok with a wrench. I used to work on my race bicycle (Kestrel 200sci) and freestyle BMX bike years ago. I have installed most small things on my car (suspension, interior stuff, oil cooler, etc.). Big stuff (clutch, anything electrical) I leave for those who know what they are doing.</TD></TR></TABLE>

*cough* diff oil flush *cough*

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by davidnyc &raquo;</TD></TR><TR><TD CLASS="quote">
4. Bent radiator support...Turn 1 Summit Point gravel PIT (Tow strap and telephone poll straighten things up nicely )
</TD></TR></TABLE>

LOL.... tow Strap and giant tree fixed mine

chris - glad he's not the only one using the redneck framerack

 

Yeah, I don't have the a socket that fits the bolt on the diff of the S2K. I had it jacked up, pump in gear oil, everything ready to go... doh! No socket. That thing is huge! Maybe a 23mm or 24mm? I am just going to go to Jiffy Lube and get it done. Don't have the time.

 

david, good luck with the race this weekend

 

David, are those springs the same as the TEIN RS ones? If so I may want the 10. I am currently using 12 front and 14 rear and may switch to 10 front 12 rear.

AW

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by AW &raquo;</TD></TR><TR><TD CLASS="quote">David, are those springs the same as the TEIN RS ones? If so I may want the 10. I am currently using 12 front and 14 rear and may switch to 10 front 12 rear.

AW</TD></TR></TABLE>

I have no idea. What is the I.D. of your springs?

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by davidnyc &raquo;</TD></TR><TR><TD CLASS="quote">Yeah, I don't have the a socket that fits the bolt on the diff of the S2K. I had it jacked up, pump in gear oil, everything ready to go... doh! No socket. That thing is huge! Maybe a 23mm or 24mm? I am just going to go to Jiffy Lube and get it done. Don't have the time.</TD></TR></TABLE>

go anywhere BUT iffy lube they are teh suck!

BTW, nice k1s
eye heart kosei

-chris

 

Rob did you install tan, domestic, 1980's vinyl seats in your R? It goes so well with PY. Great choice! :run:

 

Thanks for calling, ****

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by opie &raquo;</TD></TR><TR><TD CLASS="quote">Thanks for calling, **** </TD></TR></TABLE>

Relax, I'm sure he was concerned that we'd cause too much of a ruckus in his neighborhood.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by davidnyc &raquo;</TD></TR><TR><TD CLASS="quote">
hmmmm there seems to be a theme... Turn 1 Summit Point... </TD></TR></TABLE>

You're certainly not alone.

The first time I met Warren ****, he had just gone off the end of the runway.