marcin

cylinder heads

$100 HEAD (a6)
claened
new seals,
lapped valves
basicaly cleaned and rebuilt ready for duty.
super clean

$20 HEAD (zc) bare w/ cam caps

$20 each HEADS (assorted)
need a practice head
i have a few to choose from
a6,z6, y8, etc... let me know

$75 HEAD (z6)
complete but i would recomend rebuild

1k HEAD (z6)
fully built
-ported
-epoxied intake ports for use with non standard injector locations
-clearanced for high lift cams(crower 3)
-ridge inside of head clearanced,
-modified rockers for high lift camshafts
-new exhaust guides
-new valve guides
-3angle VJ with valves seated near edges for better flow
-supertec valves
-backcut valves
-Crower valvesprings
-Crower Ti retainers
-Crower stg. 3 Camshaft
-skunk 2 cam gear
-polished vc
___________________________________

350 BLOCK ( only about 20 heat cycles) 1 or 2 slight load low rpm around the block drives
z6 block
zc pistons
new bearings,
never ran under load because i never tuned it
________________________________________

PARTS

$475 bisimoto engineering header

$30 LS rods with pistons

$175 z6 portedmanifold, portmatched to tb and gasket, w/polished pleneum outside, gsr throttlebody

$125 cbr 38mm itbs complete with vacum log, etc

$50 busa 40mm itb's bare

$350 custom manifold for ITB's d series head flange w/0 injector slots
curently set up for 38mm cbr with stock boots, but would be easy to port for 45mm or bigger

$20 twin cam ZC camshafts w/ gears

$20 Twin cam ZC intakemanifold w/ TB

$30 z6 TB complete without throttle linkage

$75 Y8 intake manifold complete w/ TB without injectors
________________________________________________

TURBO PARTS

TURBO
$50 14b that i took apart to port, never finished... no in and out shaft play, slight left rigth
$75 Starion IC in good shape, was painted silver
$60 1g metal BOV
$60 dsm 450's
$30 Supra IC
________________________________________________
SEATS

$350 Tenzo R Rally Reclinable Bucket no rails black
_________________________________________________
TRANNY STUFF

TRANNY d series
a6 tranny, cleaned case, good tranny
$100
$200 act extreme preasure plate (like new)
act reg organic disk
$200 zex chromemolly flywheel
__________________________________________________
ELECTRONICS
$200 innovative LM1 wideband/datalogger

$75 P28 virgin auto computer(easily converts to manual)
$75 p28 dizzy
__________________________________________________ __
MISC
$20 ZEX purge solenoid with line

$15 Assorted wire harnesses 3 i think
good for plugs and spare wires
__________________________________________________ ____
$1500 SHELL
pu only
only drivers seat
89civic hatch dx model
body is in good shape, has one rust spot under pass door that needs descent ammount of work
rear quaters were fixed already
MPFI ready,
TECH,WATER, OIL PRESS, EGT guages ready
MSD 6a wired in

suspension
tockico adjustable shocks
eibach sportline springs
front back upper strutbars
lower rear tie bar
front/back sway bars (suspension techniques) (rear adjustable)
prothane all around, not every joint but the ones that count

brembo sloted rotors up front, rebuilt calipers

available with custom exhaust that exits on side behind pass door

thanks
marcin

anything not pictured please just ask and i can post or email to you.

pictures

z6 built head &itb manifold







car pics




z6 ported manifold, polished pleneum /gsr TB aem fuel rail
a6 head clened up and assembled


Modified by marcin at 7:49 PM 9/10/2006


Modified by marcin at 9:34 PM 9/10/2006


Modified by marcin at 11:26 PM 9/10/2006


Modified by marcin at 3:16 PM 9/11/2006

DelSolDon

$50 moates chip burner burn1 usb cable

$75 P28 virgin auto computer(easily converts to manual)


^^ can i get a price on those two shipped to cincinnati, OH 45245?

marcin

sent you pm don

thank you
m.