What size slicks work best for you?
#1
Thread Starter
Join Date: May 2003
Location: Gresham, OR
Posts: 477
Likes: 0
Received 0 Likes
on
0 Posts
What size slicks work best for you?
Hey I'm just wondering what size slicks work best for you guys. Heres my setup.....
96' DX Hatchback
98' B18C1
Skunk2 IM
CTR IC
DC 4-1 Header
ACT Maxx Extrem w/4-Puck
00' SI Tranny
98' JDM ITR ECU
NGK Plug Wires
Prothane Motor Mount Inserts
Skunk2 Coilovers m/Tokiko Blue Struts
My best times on these slicks....
20x6x14.....13.29 with a 1.8 60'
20x8x14.....13.62 with a 2.0 60'
22x8x15.....13.43 with a 1.9 60'
All runs are on race gas 110-120, and timing at about 18-20 degrees
The bigger slicks I have been using the most I just can't get my 60' time back down to a 1.8. I only hit 13.2 and 1.8 once with the the baby slicks but I know the time is right because they all match up, 60', 1/8 mile, and 1/4 mile.
Especially like to hear from you guys with a GSR in an EK, thanks!
96' DX Hatchback
98' B18C1
Skunk2 IM
CTR IC
DC 4-1 Header
ACT Maxx Extrem w/4-Puck
00' SI Tranny
98' JDM ITR ECU
NGK Plug Wires
Prothane Motor Mount Inserts
Skunk2 Coilovers m/Tokiko Blue Struts
My best times on these slicks....
20x6x14.....13.29 with a 1.8 60'
20x8x14.....13.62 with a 2.0 60'
22x8x15.....13.43 with a 1.9 60'
All runs are on race gas 110-120, and timing at about 18-20 degrees
The bigger slicks I have been using the most I just can't get my 60' time back down to a 1.8. I only hit 13.2 and 1.8 once with the the baby slicks but I know the time is right because they all match up, 60', 1/8 mile, and 1/4 mile.
Especially like to hear from you guys with a GSR in an EK, thanks!
#2
Not to be confused with "THE MAN"
Re: What size slicks work best for you? (B18C1EKhb)
I have a 93' CX full interior
95 LS
crower 404's
crower valve train
secret pistons (shh)
forged rods
fully blanced rotating assembly
skunk 2 manifold
dc 4-2-1 hedder
b16 tranny
MSD ignition
act clutch
100 shot NX wet kit
I run M/H 23x8.5x15 and they are bout the best size I have ran so far
good luck I hope you find a good set up.
95 LS
crower 404's
crower valve train
secret pistons (shh)
forged rods
fully blanced rotating assembly
skunk 2 manifold
dc 4-2-1 hedder
b16 tranny
MSD ignition
act clutch
100 shot NX wet kit
I run M/H 23x8.5x15 and they are bout the best size I have ran so far
good luck I hope you find a good set up.
#6
D Tranny Guru
Re: What size slicks work best for you? (B18C1EKhb)
You need 22x8x13's with your GSR motor.
WHY did the 20x8x14's not hook for you????? or did you get the 6" wide and 8" wide numbers mixed up?
WHY did the 20x8x14's not hook for you????? or did you get the 6" wide and 8" wide numbers mixed up?
Thread
Thread Starter
Forum
Replies
Last Post