THE Four Door Civic Project
#1
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
THE Four Door Civic Project
Here is a little project me and my buddy JC have been working on for a few day. Its a 95 civic four door ex model. I would like to throw big props to Jc for all his help. We both about got divorces over this car........well on to the good stuff.
This is how it sat 8 hours after the drive back from Washington D.C.(it was stock) now sitting on rota grids and bouncing on OMNI POWER coilovers.
This is how the engine bay looked like 2 days later....(the stock single slam vtec was just alittle under powered)
here a tease for u guys. this is what the waste gate was producing on a smaller spring
List of some of the goodies
Engine is a gsr sleeved and bored 84mm
scat ls crank,manley ls rods,cp slugs
p&p b16 head crower s2 turbo cams,springs and retainers, rev valves
ctr tranny with quafie
clutchmasters s5 clutch
aebs intake and throttle body
neukin turbo mani,dp and complete 3" exhaust
sc6176s turbo
s300
780 percision injectors
blah blah blah
more and better pics to come after I clean it up some. When I picked it u in D.C. it was about 97.5% stock. Only mods it had were jdm ferio badges, jdm headlights, side markers, and power folding mirrors.
This is how it sat 8 hours after the drive back from Washington D.C.(it was stock) now sitting on rota grids and bouncing on OMNI POWER coilovers.
This is how the engine bay looked like 2 days later....(the stock single slam vtec was just alittle under powered)
here a tease for u guys. this is what the waste gate was producing on a smaller spring
List of some of the goodies
Engine is a gsr sleeved and bored 84mm
scat ls crank,manley ls rods,cp slugs
p&p b16 head crower s2 turbo cams,springs and retainers, rev valves
ctr tranny with quafie
clutchmasters s5 clutch
aebs intake and throttle body
neukin turbo mani,dp and complete 3" exhaust
sc6176s turbo
s300
780 percision injectors
blah blah blah
more and better pics to come after I clean it up some. When I picked it u in D.C. it was about 97.5% stock. Only mods it had were jdm ferio badges, jdm headlights, side markers, and power folding mirrors.
#4
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
no I already had everything set to go in my hatch and something came over me to buy a four door. 3 days later Im in DC on my way back with this jewel.
thanks. I planning on stripping the rota grids and polishing them as soon as I can.
thanks. I planning on stripping the rota grids and polishing them as soon as I can.
#5
Junior Member
Join Date: Mar 2009
Location: Citrus Heights, Ca
Posts: 929
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
Not bad. Only problem, It took you 8 hours for just coilovers and wheels but only 2 days for a full swap and boost? Either way total sleeper!
#6
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
well it took 8hourson the coil overs for two reasons. number 1 I didnt I left DC at 4 in the afternoon and drove all the way home nonstop. I got to sleep at like 5:30 the next morning. number 2 I ha to wait on my buddy to get off work so we could use his shop.
Trending Topics
#9
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
gate spring which is around 10 I thin I gotta open it to make sure. it was creeping up to 11
its cool I just wanted to put that out there. It looked funny to me aswell
its cool I just wanted to put that out there. It looked funny to me aswell
#10
Honda-Tech Member
Re: THE Four Door Civic Project
good numbers. i have a similar setup with a 10lb spring and made 306whp 238tq. you may have a larger spring though if its creeping.... the springs are pretty dead on with all my experiences.
#11
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
well the tuner said my nukin mani was not the best design is the reason its creeping. he said the gate is only getting its pressure from the front 2 runners so it wont equal out causing a little creeping.
#12
Honda-Tech Member
Re: THE Four Door Civic Project
oh i see. i would look into a different mani then... boost creep is bad news. the man i looks legit... ramhorns are supposed to be one of the best, but guess not in this case.
#13
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
well it only creep up 1 pound. its a nukin ac compatible mani so it was a few $$$. Hewas telling me about a high horse power supra that had a similar design but of course for the 2jz engine. they pulled the waste gate off and it just ad a huge hole and still made 4 psi.
#14
Honda-Tech Member
Re: THE Four Door Civic Project
God dayum talk about getting to the point!!! That bay is freshhh.
Not feeling the Grids though, they look wierd for some reason.
Not feeling the Grids though, they look wierd for some reason.
#15
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
#16
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
the bay pic was also taken right after the install even before the engine was started. now those blue wires are tucked away and everything else is alittle more in place. I will get more pics soon as I clean it up
#17
Honda-Tech Member
Join Date: Feb 2008
Location: Summerville, SC, USA
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
well regardless, you all have done to that 4 door in 3 days in the time i want to have mine done in like 2 years...Rock on!
#20
Honda-Tech Member
#22
Honda-Tech Member
Thread Starter
Join Date: Jul 2007
Location: jackson, tn, usa
Posts: 1,511
Likes: 0
Received 0 Likes
on
0 Posts
Re: THE Four Door Civic Project
thanks we try hard when wee want...
weight is not really a issue for me. I will just turn he boost up.lol
thanks for the kind words guys