hybridnorth

iTrader: (2)

hey, ive been thinkin of gettin this kit, and im think of doing the 1.8 since money is tight and i cant afford ductile iron sleeves, but i was wondering if anyone has this kit and what do you think of it? any info would be awesome thanks

Furry

why would you wana do anything to a damn b16, those motors suck

NUISANCE

iTrader: (1)

Aaaaaaaa, I wanna know too.

t0p_sh0tta

How much does a stroker kit cost? I know you can get B18 blocks dirt cheap, that might be cheaper. Then you can just swap heads.

Noe Kozz

ditto, I think it would be cheaper to just get a 1.8 block and swap heads also. But it's your car, your money.

broke1

you are cool


[Modified by broke1, 11:37 AM 12/28/2002]

degooser

What kind of B18 block for cheap??? LS??? Then go LSVTEC???

those darn B18C blocks are an arm and a leg......

I would like to know how many people acutally used this B16 stroker kit and stroked their motor to a 1.8.....and how it actually turned out....

vtecvoodoo

You can do it using oem parts.

Why buy their kit for xxxx when you can just get an ls or b20 shorty for $300-700?

R you serious

well do it to a b16b block and then you have a itr motor ********

NUISANCE

iTrader: (1)

Why is it when a person asks a question it never gets answered? You guys always have to throw in opinions. I have my reasons for wanting to stick with a B16 ok.

ciRcuitJerk

you suck

AB16A2T

Go back to your hole dumb *** noob.

rsxgirlie

b16's are great..

-Whitey-

b16's are great motors i just dont see the point in stroking one to 1.8 when for all the money you spent on everything could by a b18c or maybe even a b18c5

i say buy a b16 for the 1.6 and buy a b18 for the 1.8 and if you have the money to stroke somthing just stroke up the b18 or pay a hooker to stroke me that would be great because then id be stroked to 2.2 inches

NUISANCE

iTrader: (1)

Fine, I want a stroker kit because it is balanced and I can it for around the same price I can get rods/pistons/rings and a crank for.


[Modified by NUISANCE, 11:48 PM 12/31/2002]

civictypenos

lisa kubo uses a b16 to run 8's,i hardly think they suck,yes hers is stroked out to 2.0,but it is still a b16 block.

Happyman

Okay and that's after extensive mods and a whole lot of money. Don't flame on someone because of their opinion. It's not like your opinion is better or worse than his.

hybridnorth

iTrader: (2)

hey did you say the b16 sucks? you have a b16?, sounds like the opionin of someone who dosnt know what they are talking about, these are awesome motors that can rev up to 9000 rpm and make some great power, which the 1.8 stroker you can still rev up that high and make some good power, but with the 1.8 you can get the torque. so i got this to say to you...stick a **** in it

confidence

take a look at these guys.
http://www.pacmotorsports.com/products.htm
i looked into stoking b16s a ways back and i came across these people.

Happyman

And at the end of the day it's still a b16 with a little more torque and 160 hp. Just save the extra 1000 and get a GS-R or stop arguing. You don't need to prove anything to anyone. You want to stroke your b16 .2? Then do it.

TimoneX

A b16 stroked with a B17 crank & rods and sleeved to 85-86mm is an extremely sexy motor. GSR like power w/ a r/s ratio of 1.68. B16s do not suck, but the stock crank is rather conservative. If they all came with a B17(81.4mm) crank, or this crank was more widely available the B16 would be a much more highly sought after engine.

b16 matt

furry is a flamer! If you dont know what your talking about then shut the **** up!

Heath

Anybody know anything about the stroker kits for the b18?

Jay-C

Maybe I'm missing something and I'm not trying to be a dick but if money is tight then how is buying and installing a stroker kit cheaper than buying a 1.8 block? Maybe if you let us know what your goals are with your car or why you want to stay away from the 1.8 then people would be more supportive of your idea to stroke it. So what have you already done to your b16? Also, most people don't stroke the b16 which is why you haven't gotten any opinions...cause it's just more expensive to do.

TimoneX

I just picked up a B16 stroker kit for $182. That's the B17 crank & rods. It doesn't have to be expensive if you're patient.