Spence

Have any of you put a b series in the back of a hatch?

SIcivicHATCH

It will fit I have put a d16y8 in a crx but the d16y8 is smaller though

(Civic_Duty)

i put a 4g63 (dsm) in the back of my 91 Hatch and it is bigger then a b18

JDMlyfestyle

yup ive fit a LS and D16 in the hatch at the same time

94_HATCH

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Spence &raquo;</TD></TR><TR><TD CLASS="quote">Have any of you put a b series in the back of a hatch?</TD></TR></TABLE>

Puny B series will fit with no problem. I fit my h22 in my eg hatch with the tranny still bolted onto it. I know my H is a lot bigger than your B so yes it will fit.

GdmLaz

i fitted a d16z6 with tranny and shift linkage attached but i don' have no back seats or panels or nothing

BlueIntegraBoy

iTrader: (5)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 94_HATCH &raquo;</TD></TR><TR><TD CLASS="quote">

Puny B series will fit with no problem. I fit my h22 in my eg hatch with the tranny still bolted onto it. I know my H is a lot bigger than your B so yes it will fit.</TD></TR></TABLE>

Your hatch must have been sagging like a bitch.

WrongWD

iTrader: (1)

haha try draggin a z6 home in a bone stock dx hatch. hills &gt; hatch

hatchi

ive put motors also in pass. seat area with seat removed

PLAN:B

I haven't done it w/ the tranny attatched, but my old b18c fit in my '00 CX

jdmblingn

works just fine, make sure you put a blanket or something down so you dont get oil and whatnot all over

94_HATCH

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by BlueIntegraBoy &raquo;</TD></TR><TR><TD CLASS="quote">

Your hatch must have been sagging like a bitch. </TD></TR></TABLE>

yeah it sucked Me and my 250 pound roomate. car was already dropped all the way around before we put the engine into the hatch. Rear tires were running every little dip all the way home...

komat

i always wondering this myself

going to order a motor (jdm sir2 b16a) &lt;---- how heavy are they
have it ship it to my parents business
then put it in my eg hatch

Spence

did you guys scrap that bad im thinking of buying a motor that is 4hrs away from me and my car is dropped pretty good on h&R race with tokico adjustables think i would be ok i have no rear interior?

RJonathan

I did. but it wasnt a hatch it was in a 4th gen prelude with a KA24De. and if all of you guys know a Prelude trunk isnt that big but we manage to get that sucker in and on its way home..

patastinky

yes i have done it

JDMisGOOD

Plenty of times!

RC_SKUBY

gsr in the passenger seat area of a ef the seat wasnt there though.

Jmunk

I've put a RX-7 motor in the back of mine without a problem.

Targa250R

We hauled a B18A and YS1 trans in the back of a stripped '90 hatch. Didn't even budge the suspension with 500 lbs-in spring rates in the back

Loading and unloading was a big PITA though.

will100

i have no desire to lower my car. i do want really stiff springs though. where did you find 500 lbs and how much were they? i have been looking all over. every time you search for stiff springs everything comes up lowering this lowering that. any help would be appreciated. Do you know if i can get
coilovers that stiff so i could just replace suspension nice and simple?

Deimus

When I did the swap on my Subaru, we transported the engine in the back of my 1998 Toyota Sienna minivan. It sagged the hell out of that.

I also sold the blown motor to another Subey owner, who showed up to pick up the engine with his 1994 Subaru Impreza Coupe. Needless to say, it was funny seeing him pull away with the *** sagged low!