Precision 67/65 vs Turbonetics-HPC 64/65 Dyno - Honda-Tech - Honda Forum Discussion


Forced Induction

Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

Reply
 
 
 
Thread Tools Search this Thread
Old 05-28-2011, 01:40 AM   #1
Honda-Tech Member
Thread Starter
 
.CUBISH.'s Avatar
 
Join Date: Feb 2007
Location: plantation, fl, usa
Posts: 3,118
Default Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

I've used both of these turbos on a lot of high HP car but havent had a chance to do both of them back to back.. here is a car that i finished up tonight on relatively low boost..

setup:
84x89 lsvtec
9.5 to 1 compression je pistons
eagle rods
stock port b16 head
stock b16 cams
Victorx intake
open T4 topmount
precsion 750 intercooler
E85
S300

67/65 is journal bearing with a .68 back housing
64/65 is ball bearing with a .81 back housing

both are on 18 psi



Red line= Precision 67/65 journal bearing
Blue line= Turbonetics-HPC 64/65 Ball Bearing
.CUBISH. is offline   Reply With Quote
Old 05-28-2011, 02:11 AM   #2
Honda-Tech Member
 
SlowReaction's Avatar
 
Join Date: Jan 2005
Location: Wa
Posts: 953
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

Should have used the .81 on both turbos. I believe they are interchangeable? I just picked up one for a customers car, good to see some number since I havent seen anyone else using these.
SlowReaction is offline   Reply With Quote
Old 05-28-2011, 02:14 AM   #3
Honda-Tech Member
Thread Starter
 
.CUBISH.'s Avatar
 
Join Date: Feb 2007
Location: plantation, fl, usa
Posts: 3,118
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

i did a back to back previously with the 67 with both rear housings...spool was even worse... no point comparing the 64 to that...
.CUBISH. is offline   Reply With Quote
Old 05-28-2011, 02:16 AM   #4
Honda-Tech Member
Thread Starter
 
.CUBISH.'s Avatar
 
Join Date: Feb 2007
Location: plantation, fl, usa
Posts: 3,118
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

i did a stock bore/stroke b16 back in december with the 64/68. made 800hp on 36psi
.CUBISH. is offline   Reply With Quote
Old 05-28-2011, 02:25 AM   #5
Honda-Tech Member
 
SlowReaction's Avatar
 
Join Date: Jan 2005
Location: Wa
Posts: 953
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

Good to know. Thanks for the comparison. Might have to try one of these 6465 in my own car.
SlowReaction is offline   Reply With Quote
Old 05-28-2011, 06:36 AM   #6
Honda-Tech Member
 
96 GSR-T's Avatar
 
Join Date: Mar 2006
Location: Newark, DE
Posts: 6,381
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

Nice comparison, probably 100whp sitting on the table with a good cam swap, shame such a setup has the most horrible cam available in it.
96 GSR-T is offline   Reply With Quote
Old 05-28-2011, 06:41 AM   #7
HELLO,GOOD MORNIN'
 
ahobbs's Avatar
 
Join Date: Sep 2002
Location: Savin lives
Posts: 8,910
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

interesting, thanks for the comparison
ahobbs is offline   Reply With Quote
Old 05-28-2011, 06:27 PM   #8
Honda-Tech Member
iTrader: (5)
 
Casey's Avatar
 
Join Date: Dec 2001
Location: the internet and I WILL STEP ON YOU
Posts: 8,979
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

nice comparison. what would change at higher hp levels? is this the billet turbonetics? i was trying to find it on their website
Casey is offline   Reply With Quote
Old 05-28-2011, 08:02 PM   #9
Honda-Tech Member
Thread Starter
 
.CUBISH.'s Avatar
 
Join Date: Feb 2007
Location: plantation, fl, usa
Posts: 3,118
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

yeah its the billet Turbonetics... hard to say on higher boost levels, but i have made 850hp on the 64 before so i dont see it falling off too much compared to the 67 on higher boost
.CUBISH. is offline   Reply With Quote
Old 05-29-2011, 12:52 PM   #10
Honda-Tech Member
 
DelSolMarine's Avatar
 
Join Date: Jan 2006
Location: Suffolk, Virginia
Posts: 1,274
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

if the precision was a ball bearing turbo like the turbonetics one that would have made for more of a fair comparison as well... still interesting
DelSolMarine is offline   Reply With Quote
Old 05-29-2011, 03:06 PM   #11
Honda-Tech Member
Thread Starter
 
.CUBISH.'s Avatar
 
Join Date: Feb 2007
Location: plantation, fl, usa
Posts: 3,118
Default Re: Precision 67/65 vs Turbonetics-HPC 64/65 Dyno

a lot of things could have made it more fair... same housings..bb..etc.. but these are the turbos i had. point was to show that the billet 64 is a very capable turbo
.CUBISH. is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Garrett GTW series turboes rudebwoy Drag Racing 17 10-23-2015 03:01 PM
Turbonetics Custom Turbos, BOV's and Wastegate Specials!!! [email protected] Forced Induction 181 08-08-2012 11:13 AM
800+hp part out... plus recaros, zeal suspension, etc .CUBISH. Florida (Sales) 11 01-15-2012 05:18 PM
Comp Turbo ct4 6465 billet or Precision 6266 billet, for 600hp goal Civicsir93 Forced Induction 27 01-06-2012 12:30 PM
Question for the turbo guru's Jonny-X Forced Induction 21 02-06-2011 07:43 PM


Tags
115, 6265, 64, 6465, 65, 67, 6765, 68, billet, gt40, highest, hp, hpc, precision, turbonetics

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -8. The time now is 02:49 AM.


 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: