(again) Vafc, throttle percent (low)(hi)
#1
Thread Starter
Join Date: Oct 2002
Location: Torrance/Lomita, Ca, u.s.a.
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
(again) Vafc, throttle percent (low)(hi)
Hey well i have worked out lots of bugs in my injector swap. but i need to know now is ...for the LOW and HI percents for Throttle.. should i run 5% and 45%.. i was told i should run these numbers.. after i was told to run 98% 99%, low and hi. please help me.. do u think that 5% and 45% will help or what should i do now
#2
Honda-Tech Member
Join Date: Nov 2001
Location: TheNine2Five, Ca, USA
Posts: 1,213
Likes: 0
Received 0 Likes
on
0 Posts
Re: (again) Vafc, throttle percent (First Gen Man)
With the Hack, it doesn't matter what Low/High throttle you set 1/2% or 98/99%, the maps are the same on both sides. I have mine at 98/99%- running fine to 11psi-NO CEL's
#3
Thread Starter
Join Date: Oct 2002
Location: Torrance/Lomita, Ca, u.s.a.
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
Re: (again) Vafc, throttle percent (integracon)
im NOT running the hack...
and that is why my car is messed up.. i get it to pull .. but it seems like it is too rich.. but i dont get it how i can (+) the 1k fuel .. and it will idle better
and that is why my car is messed up.. i get it to pull .. but it seems like it is too rich.. but i dont get it how i can (+) the 1k fuel .. and it will idle better
#4
Member
Re: (again) Vafc, throttle percent (First Gen Man)
geeze, familiar location torrance/lomita...anyways...go to a local dyno, i'm not sure where there is one of those anymore around those parts...but start asking the shops...BTW which shops are in the area....i'll be going back home to SO cal, and intrested what is going on around those parts.
Trending Topics
#8
Honda-Tech Member
Join Date: Sep 2002
Location: Beavercreek, OH 45431
Posts: 994
Likes: 0
Received 0 Likes
on
0 Posts
Re: (again) Vafc, throttle percent (First Gen Man)
If your using the AFC to run bigger injectors, you are doing the hack... That IS the hack. It just so happens the hack also allows you to run boost. About %'s to set throttle position, it doesn't matter. I heard that the honda ECU switches from closed to open loop @ 70% so i put mine @ 70/71% so i could tune differently for open loop if I wanted to. Works fine, but I played with a whole lot of settings and it didn't matter which I chose. Hope this helps
#10
Honda-Tech Member
Join Date: Feb 2001
Location: Boston, MA
Posts: 1,491
Likes: 0
Received 0 Likes
on
0 Posts
Re: (again) Vafc, throttle percent (First Gen Man)
I set it up with nothing special done to the VAFC just install it the way it suppose too. Set everything down to -40% and had throttle position at 98%-99%. No missing link. It works great with A/F at 12:1
#11
Honda-Tech Member
Join Date: Nov 2001
Location: TheNine2Five, Ca, USA
Posts: 1,213
Likes: 0
Received 0 Likes
on
0 Posts
Re: (again) Vafc, throttle percent (First Gen Man)
Should i USE the missing link ..?... and what fuel pressure..
HOWEVER, since you are only using 390's not sure if the voltage will be decreased enough for you to do it. Try it and see- it may allow you 6psi w/o a CEL.
Those 390's might be too BIG to run the Missing Link and too SMALL to run without it...
[Modified by integracon, 6:54 PM 12/27/2002]
Thread
Thread Starter
Forum
Replies
Last Post
smurfey002
Forced Induction
5
03-17-2004 10:34 AM