H-series Custom Turbo kit
#1
H-series Custom Turbo kit
Been doing some upgrades, so here is what I have for some Lucky person, cause I have had very little usage of these parts, and some are new.This is perfect for someone doing an H-series turbo kit, I made 453HP and 337TQ at 17psi on pump gas.
1) T3 Lovefab MiniMe EQ tubular manifold with a Tial V60 WG V-band flange. ( Already wrapped in DEI thermal wrapping and coated in the high-temp DEI silicone spray coating ) With studs and nuts. $350 obo
2) Custom Dumptube to fit this setup with the Tial V60 V-band Dump flange...also wrapped and coated in DEI's thermal wrapping and spray coated. $45
3) Custom V-band 3" downpipe, all professionally tig-welded with a Vibrant performance 6 inch Turbo interlock flex coupler with multiple ozygen sensor bungs for diff locations or multiple O2 sensors. ( also wrapped and coated in DEI thermal wrapping and spray coated in DEI's High-temp coating.) $100
4) Garrett GT3076R .82AR Dual Ballbearing water cooler turbo with V-band housing ( fits perfect to the downpipe I have for sale here ) I purchased this turbo Brand new from T1 Race Developement, worked perfect, used it for about 2 summers ( maybe 2000km of driving on it ) Last summer had a clogged oil restrictor which fried the bearings so I sent it to ATP Turbo for inspection and they replaced the entire CHRA center-section with a brand new unit and re-used my compressor housing and turbine housing because they were in perfect condition, was tested, and sent back to me as a Brand New Turbo. I used it for another 4-5 drives in the car around town and stored the car for the winter in the fall. Also comes with all the Garrett GT series Oil drain fittings including the restrictor AND the custom made braiaded stainless teflon water lines i had made also with the Garrett water line fittings bought from ATP turbo. $1000.00 obo
5) I have a T3/T4 turbine blanket bought from T1 Race Developement with some minor wear and a small hole from rubbing against the dumptube. I will throw that in with the turbo to whoever wants it.. - free with turbo
6) H22 ACT extreme HD Clutch, with a 6 puck sprung disk used for only one summer approx 2000km of driving on it, and never launched hard once on it ( in fear of blowing my tranny apart or snapping an axle lol ) $400
7) H22 Evolution lightweight flywheel 8.9lbs ( with timing marks! ) used with the ACT clutch, and had a replacable disk $100
8) H22 Stage 4 Bully Clutch and Bullly lightweight flywheel. I had this on my car for a few summers, When I finally had my last setup re-tuned for more power, it couldnt handle the torque and started to slip, so I replaced it with the ACT one. But this clutch also has very limited usage and Bully clutch re-pucks the clutch disks for cheap, with a very fast turn-around time so for anyone who wants a decent clutch for an H22 setup, I will sell it for cheap. $50
9) 2 Willwood 12.5'' two piece Rotors with minimal usage...I had them on my car but needed to drop down to a beefier tire for better traction so I had to go with a smaller rotor size to fit the new rims.. Not sure what these got for individually, make me an offer...
10) Brand New Autometer electric fuel pressure guage. new in Box.. $100
1) T3 Lovefab MiniMe EQ tubular manifold with a Tial V60 WG V-band flange. ( Already wrapped in DEI thermal wrapping and coated in the high-temp DEI silicone spray coating ) With studs and nuts. $350 obo
2) Custom Dumptube to fit this setup with the Tial V60 V-band Dump flange...also wrapped and coated in DEI's thermal wrapping and spray coated. $45
3) Custom V-band 3" downpipe, all professionally tig-welded with a Vibrant performance 6 inch Turbo interlock flex coupler with multiple ozygen sensor bungs for diff locations or multiple O2 sensors. ( also wrapped and coated in DEI thermal wrapping and spray coated in DEI's High-temp coating.) $100
4) Garrett GT3076R .82AR Dual Ballbearing water cooler turbo with V-band housing ( fits perfect to the downpipe I have for sale here ) I purchased this turbo Brand new from T1 Race Developement, worked perfect, used it for about 2 summers ( maybe 2000km of driving on it ) Last summer had a clogged oil restrictor which fried the bearings so I sent it to ATP Turbo for inspection and they replaced the entire CHRA center-section with a brand new unit and re-used my compressor housing and turbine housing because they were in perfect condition, was tested, and sent back to me as a Brand New Turbo. I used it for another 4-5 drives in the car around town and stored the car for the winter in the fall. Also comes with all the Garrett GT series Oil drain fittings including the restrictor AND the custom made braiaded stainless teflon water lines i had made also with the Garrett water line fittings bought from ATP turbo. $1000.00 obo
5) I have a T3/T4 turbine blanket bought from T1 Race Developement with some minor wear and a small hole from rubbing against the dumptube. I will throw that in with the turbo to whoever wants it.. - free with turbo
6) H22 ACT extreme HD Clutch, with a 6 puck sprung disk used for only one summer approx 2000km of driving on it, and never launched hard once on it ( in fear of blowing my tranny apart or snapping an axle lol ) $400
7) H22 Evolution lightweight flywheel 8.9lbs ( with timing marks! ) used with the ACT clutch, and had a replacable disk $100
8) H22 Stage 4 Bully Clutch and Bullly lightweight flywheel. I had this on my car for a few summers, When I finally had my last setup re-tuned for more power, it couldnt handle the torque and started to slip, so I replaced it with the ACT one. But this clutch also has very limited usage and Bully clutch re-pucks the clutch disks for cheap, with a very fast turn-around time so for anyone who wants a decent clutch for an H22 setup, I will sell it for cheap. $50
9) 2 Willwood 12.5'' two piece Rotors with minimal usage...I had them on my car but needed to drop down to a beefier tire for better traction so I had to go with a smaller rotor size to fit the new rims.. Not sure what these got for individually, make me an offer...
10) Brand New Autometer electric fuel pressure guage. new in Box.. $100
#2
Re: H-series Custom Turbo kit
The Turbo, manifold, downpipe, dumptube, turbine blanket, I would be willing to do a combo price and give someone a sweet deal, and I used ID1000's with my setup and might be selling them as well in the next few weeks, I could even provide my Hondata calibration for whoever wants it for their setup...
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
dumafit
Northern California (Sales)
12
06-21-2009 11:15 AM