GC perch issue.. need help
#1
Honda-Tech Member
Thread Starter
Join Date: Mar 2012
Location: Lebanon
Posts: 252
Likes: 0
Received 0 Likes
on
0 Posts
GC perch issue.. need help
Hello,
Im just getting pissed off from my GC kit.
Either the perches are defective or I am misunderstanding the installing procedure.
Once setting the required position of the perch on the sleeve, then i should tighten the screw so that the perch does not rotate on the sleeve.
This is what i am doing before asseblming the kit.
Simply the sleeves and perch in hands.
So what is going wrong that the perch is not tightening knowing that the scew is very well tightened!!!
Has anybody faced such issue??
Im just getting pissed off from my GC kit.
Either the perches are defective or I am misunderstanding the installing procedure.
Once setting the required position of the perch on the sleeve, then i should tighten the screw so that the perch does not rotate on the sleeve.
This is what i am doing before asseblming the kit.
Simply the sleeves and perch in hands.
So what is going wrong that the perch is not tightening knowing that the scew is very well tightened!!!
Has anybody faced such issue??
#2
Re: GC perch issue.. need help
so you have the screw in the collar tight while you are trying to turn it to adjust your ride height?
you should loosen that screw a little when you go to turn the collar, that screw clamps the collar in place so it doesnt unthread and change your ride height as you go down the road
you should loosen that screw a little when you go to turn the collar, that screw clamps the collar in place so it doesnt unthread and change your ride height as you go down the road
#3
Honda-Tech Member
Thread Starter
Join Date: Mar 2012
Location: Lebanon
Posts: 252
Likes: 0
Received 0 Likes
on
0 Posts
#4
The Grumpiest
iTrader: (4)
Join Date: May 2008
Location: Oak Ridge, TN, USA
Posts: 28,333
Likes: 0
Received 16 Likes
on
15 Posts
Re: GC perch issue.. need help
IF that's true then you have a defective collar more than likely. No need to keep creating new threads about the same issue. Contact Ground Control.
Trending Topics
#9
Honda-Tech Member
Thread Starter
Join Date: Mar 2012
Location: Lebanon
Posts: 252
Likes: 0
Received 0 Likes
on
0 Posts
Re: GC perch issue.. need help
Damnn it was just a matter of extra tightening, but I was worried about breaking the screw coz I read somewhere not to over tighten it.
anyway its fixed now
Next will be installation
thanks
anyway its fixed now
Next will be installation
thanks
#10
Honda-Tech Member
Join Date: Jun 2004
Location: Sherman Oaks, CA, United States
Posts: 7,539
Likes: 0
Received 4 Likes
on
4 Posts
Re: GC perch issue.. need help
You actually don't need to bother "tightening" the screw that much. The vehicle weight will prevent the seat from spinning. If you over torque that little screw, you're going to have a heck of a time trying to loosen it later to make adjustments.
#11
Honda-Tech Member
Join Date: Jan 2008
Location: PA, US
Posts: 3,689
Likes: 0
Received 0 Likes
on
0 Posts
Re: GC perch issue.. need help
it even says in the paper instruction, don't over tighten, just till it's snug.
Thread
Thread Starter
Forum
Replies
Last Post
george34
Road Racing / Autocross & Time Attack
7
09-19-2005 06:00 PM
94lsvtec
Acura Integra
2
03-14-2005 03:10 PM
DoctorGSR
Suspension & Brakes
17
03-06-2005 06:52 PM