Built b16 turbo problem
#1
Honda-Tech Member
Thread Starter
iTrader: (2)
Join Date: Dec 2004
Location: Panama City Beach, Fl.
Posts: 1,428
Likes: 0
Received 0 Likes
on
0 Posts
Built b16 turbo problem
I got a 82mm Dart sleeved b16 motor. Stock b16 head with itr cams. I'm running an AFI turbo kit AC ranhorn with a full 3 inch exhaust. Its got a Garrett T3/T04E 57 trim. 2 inch hotside piping and 2.5 cold side pipe. My question is, when it was tuned it did 280@10 psi and 375@15 psi. But anytime was went over 16psi we started losing power. I'm trying to figure out if its the small intercooler or the 2 inch hotside pipe. If anyone had any input please let me know.
Thanks alot Chris
Thanks alot Chris
#2
Re: Built b16 turbo problem
I got a 82mm Dart sleeved b16 motor. Stock b16 head with itr cams. I'm running an AFI turbo kit AC ranhorn with a full 3 inch exhaust. Its got a Garrett T3/T04E 57 trim. 2 inch hotside piping and 2.5 cold side pipe. My question is, when it was tuned it did 280@10 psi and 375@15 psi. But anytime was went over 16psi we started losing power. I'm trying to figure out if its the small intercooler or the 2 inch hotside pipe. If anyone had any input please let me know.
Thanks alot Chris
Thanks alot Chris
#4
Honda-Tech Member
iTrader: (4)
Join Date: Apr 2005
Location: South, Texas
Posts: 12,903
Likes: 0
Received 0 Likes
on
0 Posts
Re: Built b16 turbo problem
It's not the turbo. The turbo is good for 400-450 and somewhat over 20 psi. Did the car not make any more power or the gains per psi of boost weren't much? What's the full setup down to the last everything. Exhaust size turbine housing size. How much of the charge pipin is 2"
#6
Honda-Tech Member
Thread Starter
iTrader: (2)
Join Date: Dec 2004
Location: Panama City Beach, Fl.
Posts: 1,428
Likes: 0
Received 0 Likes
on
0 Posts
Re: Built b16 turbo problem
It's not the turbo. The turbo is good for 400-450 and somewhat over 20 psi. Did the car not make any more power or the gains per psi of boost weren't much? What's the full setup down to the last everything. Exhaust size turbine housing size. How much of the charge pipin is 2"
Its a Garrett T3/TO4E 57 trim. Its a full AFI ram horn ac kit. Full 3 inch exhaust and dp. Its only 2 inch piping from the turbo to the ic. I believe its a .62 a/r exhaust housing. Anything over 16 psi it would start to lose power.
Trending Topics
#9
Honda-Tech Member
iTrader: (4)
Join Date: Apr 2005
Location: South, Texas
Posts: 12,903
Likes: 0
Received 0 Likes
on
0 Posts
Re: Built b16 turbo problem
Intake temps are higher than I'd lik to see that's for sure. Is the whole charge piping 2" or just the hotside? I run 2" just off the turbo for fit ent issues which is about 9 inches then go right to 2.5 the rest of the way. I believe with 2" your reaching or surpassing recomended Mach air speed inside the charge piping by running alot more boost. Try a larger hotside
#11
Honda-Tech Member
iTrader: (4)
Join Date: Apr 2005
Location: South, Texas
Posts: 12,903
Likes: 0
Received 0 Likes
on
0 Posts
Re: Built b16 turbo problem
It should be ok but try larger. The intercooler is probably to small and those intake temps will reduce power production. Plus the ic maybe be restricting
Thread
Thread Starter
Forum
Replies
Last Post