ignition output signal CEL #15
11-06-2008, 03:43 PM
#1
Honda-Tech Member
Thread Starter
Join Date: Nov 2005
Location: laguna niguel, ca, usa
Posts: 1,600
Likes: 0
Received 0 Likes
on
0 Posts
ignition output signal CEL #15
hey guys i had a code 9 the other day CYP sensor (cyl 1 sensor), so i bought and installed a new dizzy from AZ and i was driving home and my car just shut off and a code 15 popped up. I think there may be a wiring problem near my ecu, so i checked those wires out and fixed a couple.
Cliff notes:
95 del sol si (jdm sohc vtec JDMd15b obd1)
car wont start (but will everyonce in a while when i tinker with the wires but shuts off
CEL #15 ignition output signal
anyone have some expertise?
Cliff notes:
95 del sol si (jdm sohc vtec JDMd15b obd1)
car wont start (but will everyonce in a while when i tinker with the wires but shuts off
CEL #15 ignition output signal
anyone have some expertise?
11-07-2008, 01:31 PM
#3
Re: ignition output signal CEL #15 (obuhmyuh)
Here's where to concentrate:
1) The igniter may be bad.
2) The Yel/Grn wire between the igniter and ECU may be bad (open or short).
3) The Blk/Yel wire between distributor 2P connector and ignition switch may be bad. There should be battery voltage with the key turned to ON(II).
1) The igniter may be bad.
2) The Yel/Grn wire between the igniter and ECU may be bad (open or short).
3) The Blk/Yel wire between distributor 2P connector and ignition switch may be bad. There should be battery voltage with the key turned to ON(II).
11-07-2008, 01:34 PM
#4
Honda-Tech Member
Thread Starter
Join Date: Nov 2005
Location: laguna niguel, ca, usa
Posts: 1,600
Likes: 0
Received 0 Likes
on
0 Posts
Re: ignition output signal CEL #15 (RonJ@HT)
yeah all of my wires are hacked to bits around that area by my ECU. I tried using a different ECU as well...
sounds like im going to need a mutimeter, i checked for power at the yellow/green wire using a lightbulb and ground and it looks like theres power there (maybe insufficient though???), i literally had just replaced the dizzy when this **** happened and i was driving away from autozone, so im not thinkin its the dizzy too much since its new...
sounds like im going to need a mutimeter, i checked for power at the yellow/green wire using a lightbulb and ground and it looks like theres power there (maybe insufficient though???), i literally had just replaced the dizzy when this **** happened and i was driving away from autozone, so im not thinkin its the dizzy too much since its new...
11-09-2008, 04:54 PM
#7
Honda-Tech Member
iTrader: (2)
Join Date: Sep 2007
Location: columbia, sc, united states
Posts: 1,030
Likes: 0
Received 0 Likes
on
0 Posts
Re: ignition output signal CEL #15 (obuhmyuh)
hey did you ever figure this out? my buddy has the same problem but he has no spark, and throwing code 15.
Trending Topics
07-30-2009, 09:35 PM
#11
Re: ignition output signal CEL #15
Does the Blk/Yel wire in the distributor have battery voltage with the key in ON(II)?
Does the Yel/Grn wire running between the igniter unit and ECU have continuity? What voltage does this wire have at the igniter unit with the key in ON(II)?
07-31-2009, 09:11 AM
#12
Honda-Tech Member
Join Date: Apr 2004
Location: SoFlo
Posts: 1,884
Likes: 0
Received 0 Likes
on
0 Posts
Re: ignition output signal CEL #15
the cars at a friends house and hes working on it but he hasnt been about to figure anything out...ima text him what u wrote...what if the blk/yel wire in the dizzy has voltage?
07-31-2009, 09:25 AM
#14
Re: ignition output signal CEL #15
07-31-2009, 10:46 AM
#16
12-28-2009, 10:37 AM
#24
Honda-Tech Member
Join Date: Sep 2008
Location: San Diego, CA US
Posts: 1,452
Likes: 0
Received 0 Likes
on
0 Posts
