Help...OBD II Code Question?
#1
Junior Member
Thread Starter
Join Date: Jan 2005
Location: Sin City, ca, USA
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Help...OBD II Code Question?
My friends car is throwing two codes right now and Im not sure on how to diagnose this problem....
54 P1336 CSF Sensor Intermittent Interruption
and the other code is a P1399 and I cant find the definition of this code anywhere. I looked on the threads on this site and no luck!!!
54 P1336 CSF Sensor Intermittent Interruption
and the other code is a P1399 and I cant find the definition of this code anywhere. I looked on the threads on this site and no luck!!!
#3
Junior Member
Thread Starter
Join Date: Jan 2005
Location: Sin City, ca, USA
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Re: Help...OBD II Code Question? (DC2_JAPAN)
I know there are a lot of techs on here with a lot of knowledge so if anyone can help I would much appreciate it. THANKS
#6
Honda-Tech Member
P1336 Engine Speed (RPM) Fluctuation Sensor Intermittent Interruption
that last code is for chrysler = "wait to start"
You should not be getting that code at all....ever
Check the codes the other way:
https://honda-tech.com/zerothread/1901557
Come back with what those codes are
that last code is for chrysler = "wait to start"
You should not be getting that code at all....ever
Check the codes the other way:
https://honda-tech.com/zerothread/1901557
Come back with what those codes are
Trending Topics
#8
Honda-Tech Member
Join Date: Jan 2006
Location: Rochester, New York -> Santa Clara, CA
Posts: 10,443
Likes: 0
Received 2 Likes
on
2 Posts
Re: (DC2_JAPAN)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by DC2_JAPAN »</TD></TR><TR><TD CLASS="quote">but what is that code tryin to tell me? how do i diagnose it?</TD></TR></TABLE>
By doing it the right way.
You shouldn't be getting codes that are impossible for the ECU to emit.
Follow the link pdiggitydogg gave you.
By doing it the right way.
You shouldn't be getting codes that are impossible for the ECU to emit.
Follow the link pdiggitydogg gave you.
#9
Junior Member
Thread Starter
Join Date: Jan 2005
Location: Sin City, ca, USA
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Re: (Syndacate)
What I mean is.... what exactly is this telling me?
P1336 Engine Speed (RPM) Fluctuation Sensor Intermittent Interruption
Is it electrical, mechanical, do I need to replace anything, HOW do I diagnose this problem?
P1336 Engine Speed (RPM) Fluctuation Sensor Intermittent Interruption
Is it electrical, mechanical, do I need to replace anything, HOW do I diagnose this problem?
#11
Junior Member
Thread Starter
Join Date: Jan 2005
Location: Sin City, ca, USA
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Re: (DC2_JAPAN)
54 CKF - crank fluctuation sensor
I did the jump and thats what it says... Could the sensor be bad? could a fuse be bad? could there be something wrong with the wiring? These are the kinds of questions im looking to be answered
I did the jump and thats what it says... Could the sensor be bad? could a fuse be bad? could there be something wrong with the wiring? These are the kinds of questions im looking to be answered
#12
Junior Member
Thread Starter
Join Date: Jan 2005
Location: Sin City, ca, USA
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Re: (DC2_JAPAN)
Where would this sensor be located and do any of you know what the Voltage specs should be for it? I have a DMM so I can test voltage for it... Thanks
#15
Honda-Tech Member
you bumped exactly one minute later?
Its located on the oil pump, behind the timing belt, near the crank pulley
Connector is 3 pin and can be seen coming from that area
With ignition OFF:
disconnect ckf and measure the resisntance between pins 1 and 3
Spec ~ 1.6-3.2k
If thats good, then check for individual continuity between both 1 and ground and 3 and ground
Is your friend using an obd1 engine with an obd2 ecu?
Its located on the oil pump, behind the timing belt, near the crank pulley
Connector is 3 pin and can be seen coming from that area
With ignition OFF:
disconnect ckf and measure the resisntance between pins 1 and 3
Spec ~ 1.6-3.2k
If thats good, then check for individual continuity between both 1 and ground and 3 and ground
Is your friend using an obd1 engine with an obd2 ecu?
Thread
Thread Starter
Forum
Replies
Last Post