Intake manifold Vacuum leak?
#1
Honda-Tech Member
Thread Starter
Join Date: Oct 2011
Posts: 460
Likes: 0
Received 0 Likes
on
0 Posts
Intake manifold Vacuum leak?
1989 civic 4 door Dx
b18a1 block b1 head
P75 intake manifold
dc headers
Everything else stock
P75 ecu
Okay I bought my self a used working condition intake manifold.
Took out the old one.
Put in the new intake gasket.
And installed Intake manifold. Put it on "On position" and checks out good
Cel comes on and off. Have a leak on one of the fuel filter lines.
So i go ahead and start it up. Heard a Very Loud whining noise!
Like it sounds like a super charger but at idle. Try to listen where its coming from
but its too loud. Loud that it hurts my f*CKN EARS. LOL
Tried adjusting idle nothing. It also idles very high. 1500
It has a jumpy idle it goes from 100+/-
Never heard of this before. Any suggestion before i pull it off again.
b18a1 block b1 head
P75 intake manifold
dc headers
Everything else stock
P75 ecu
Okay I bought my self a used working condition intake manifold.
Took out the old one.
Put in the new intake gasket.
And installed Intake manifold. Put it on "On position" and checks out good
Cel comes on and off. Have a leak on one of the fuel filter lines.
So i go ahead and start it up. Heard a Very Loud whining noise!
Like it sounds like a super charger but at idle. Try to listen where its coming from
but its too loud. Loud that it hurts my f*CKN EARS. LOL
Tried adjusting idle nothing. It also idles very high. 1500
It has a jumpy idle it goes from 100+/-
Never heard of this before. Any suggestion before i pull it off again.
Last edited by BIGef; 10-27-2012 at 07:49 AM. Reason: Added car information
#2
Honda-Tech Member
Join Date: Oct 2006
Location: Gulf Coast, FL, usa
Posts: 657
Likes: 0
Received 0 Likes
on
0 Posts
Re: Intake manifold Vacuum leak?
You can check vacuum leaks with many substances,but one of the more common-safer ones is wd-40 which will make engine "bog" when sprayed onto a vacuum leak such as @ the gasket or throttle body. (propane is used in alot of shops,you can use most canned aerosol solvents (they make engine rev up in rpm) but some are highly flammable so spraying on hot engine surfaces involve some danger of fire when using them!!!) You can check vacuum lines by "pinching" them flat momentarily whilst running if suspected leak there... G' Luck!
#3
Honda-Tech Member
Thread Starter
Join Date: Oct 2011
Posts: 460
Likes: 0
Received 0 Likes
on
0 Posts
Re: Intake manifold Vacuum leak?
Okay It was a vacuum leak from the intake manifold gasket.
Apparently i took out the whole intake manifold again.
And found out that i forgot to scrape the old gasket off >.< FML
Making is leave space for the vacuum to go in. Also coolant went inside #4 cylinder intake manifold. -_-
Will fuel pressure effect if its leaking from the banjo bolts on the fuel filter?
Apparently i took out the whole intake manifold again.
And found out that i forgot to scrape the old gasket off >.< FML
Making is leave space for the vacuum to go in. Also coolant went inside #4 cylinder intake manifold. -_-
Will fuel pressure effect if its leaking from the banjo bolts on the fuel filter?
#4
Honda-Tech Member
Join Date: Oct 2006
Location: Gulf Coast, FL, usa
Posts: 657
Likes: 0
Received 0 Likes
on
0 Posts
Re: Intake manifold Vacuum leak?
Okay It was a vacuum leak from the intake manifold gasket.
Apparently i took out the whole intake manifold again.
And found out that i forgot to scrape the old gasket off >.< FML
Making is leave space for the vacuum to go in. Also coolant went inside #4 cylinder intake manifold. -_-
Will fuel pressure effect if its leaking from the banjo bolts on the fuel filter?
Apparently i took out the whole intake manifold again.
And found out that i forgot to scrape the old gasket off >.< FML
Making is leave space for the vacuum to go in. Also coolant went inside #4 cylinder intake manifold. -_-
Will fuel pressure effect if its leaking from the banjo bolts on the fuel filter?
Replace the aluminum crush washers that are between both sealing surfaces of the banjos,you do not want fuel leaking onto a hot engine/manifold,etc... But yeah,a leak will affect fuel pressure if it's big enough,but NONE are acceptable!!! = FIRE if not repaired!!! G' Luck!
#5
Honda-Tech Member
Thread Starter
Join Date: Oct 2011
Posts: 460
Likes: 0
Received 0 Likes
on
0 Posts
Re: Intake manifold Vacuum leak?
Okay another ISSUE:
Fixed leak so checks out okay.
Cold start it idles at 1700-1800
Then when it warms idles at 8-900 No probs.
When i take it for a drive i go 30-40mph and braking/coming to a stop car idle drops and wants to die.
Went to gas station to see any probs cant seem to find but i hear hissing noise not sure if its intake or a leak again
Then drive out gas station i die out but starts right back up. Died like 3 times even when driving 15+mph
Fixed leak so checks out okay.
Cold start it idles at 1700-1800
Then when it warms idles at 8-900 No probs.
When i take it for a drive i go 30-40mph and braking/coming to a stop car idle drops and wants to die.
Went to gas station to see any probs cant seem to find but i hear hissing noise not sure if its intake or a leak again
Then drive out gas station i die out but starts right back up. Died like 3 times even when driving 15+mph
#6
Honda-Tech Member
Thread Starter
Join Date: Oct 2011
Posts: 460
Likes: 0
Received 0 Likes
on
0 Posts
Re: Intake manifold Vacuum leak?
STILL having the same prob. Took out manifold and cleaned it up more with a razor.
Reinstalled everything.
FUEL pressure at idle is 39-40 psi
when driving/cruising ill let the car roll/idle/neutral
The car idle drops and slowly dies.
I tried pressing the gas pedal to keep it from stalling but ends up dying.
also when i brake idle drops
tried adjusting idle by disconnecting the iacv but it rpm drops all the way to 100-200rpm
then played with the idle screw no change.
Reinstalled everything.
FUEL pressure at idle is 39-40 psi
when driving/cruising ill let the car roll/idle/neutral
The car idle drops and slowly dies.
I tried pressing the gas pedal to keep it from stalling but ends up dying.
also when i brake idle drops
tried adjusting idle by disconnecting the iacv but it rpm drops all the way to 100-200rpm
then played with the idle screw no change.
Trending Topics
#14
Honda-Tech Member
Thread Starter
Join Date: Oct 2011
Posts: 460
Likes: 0
Received 0 Likes
on
0 Posts
Re: Intake manifold Vacuum leak?
Reseted ecu and test drove it nothing new
Also noticed when i first installed the intake manifold fuel pressure at idle was about 36.
It went higher after 3rd attempt of reinstalling it. 39-40 psi
Also noticed when i first installed the intake manifold fuel pressure at idle was about 36.
It went higher after 3rd attempt of reinstalling it. 39-40 psi
Thread
Thread Starter
Forum
Replies
Last Post
ilu
Honda Civic / Del Sol (1992 - 2000)
7
04-19-2006 03:08 PM