dzminiz's D16 Engine Rebuild Kit
#1
Honda-Tech Member
Thread Starter
dzminiz's D16 Engine Rebuild Kit
i spun a bearing so im lookin toward a rebuild kit, as long as i didn't bend anything, so new bearings, oil pump, ANY1 Know Where To Find A Kit??
Thanks
Thanks
#2
Honda-Tech Member
Join Date: Jan 2003
Location: the backwoods, usa
Posts: 2,841
Likes: 0
Received 0 Likes
on
0 Posts
Re: d16 rebuild kit (dzminiz)
i dont know if anybody sells a complete rebuild "kit" but you can pick up some ACL bearings from a couple different distributors on this site, one of them being EARL. you can pick up a gasket set and oil pump from your local honda dealer. hope that helps a little. maybe somebody else has some pointers about where to pick up gaskets for a better price.
#5
MiG-21 superfan
Join Date: Mar 2001
Location: near the ocean, Moderator City, NJ
Posts: 8,628
Likes: 0
Received 3 Likes
on
3 Posts
Re: d16 rebuild kit (dzminiz)
http://www.importperformanceparts.net offers alot of rebuild parts, like higher-flowing oil pumps and bearings
http://www.hondaautomotiveparts.com is a decent source for parts, i know their sister site acuraautomotiveparts.net offers honda part for 25% off OE list....
http://www.hondaautomotiveparts.com is a decent source for parts, i know their sister site acuraautomotiveparts.net offers honda part for 25% off OE list....
#6
Re: (dzminiz)
if you spun a rod bearing, the crank is going to need to be checked out, to see if you ate the journal up.
i can sell you a package deal that will give you a great basis for an all motor d16. if all you need is bearings, pistons, rings, pins, and a gasket kit, off the top of my head i could sell it for $500.
i can sell you a package deal that will give you a great basis for an all motor d16. if all you need is bearings, pistons, rings, pins, and a gasket kit, off the top of my head i could sell it for $500.
#7
Re: (CallMeJesus)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by CallMeJesus »</TD></TR><TR><TD CLASS="quote">if you spun a rod bearing, the crank is going to need to be checked out, to see if you ate the journal up.
i can sell you a package deal that will give you a great basis for an all motor d16. if all you need is bearings, pistons, rings, pins, and a gasket kit, off the top of my head i could sell it for $500.</TD></TR></TABLE>
Why would he need new pistons?
i can sell you a package deal that will give you a great basis for an all motor d16. if all you need is bearings, pistons, rings, pins, and a gasket kit, off the top of my head i could sell it for $500.</TD></TR></TABLE>
Why would he need new pistons?
Trending Topics
#8
MiG-21 superfan
Join Date: Mar 2001
Location: near the ocean, Moderator City, NJ
Posts: 8,628
Likes: 0
Received 3 Likes
on
3 Posts
Re: (LSVTEC 91 Civic)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by LSVTEC 91 Civic »</TD></TR><TR><TD CLASS="quote">
Why would he need new pistons?</TD></TR></TABLE>
for a bump in compression he could select a set of OE pistons from another d, such as p29 or something-----
Why would he need new pistons?</TD></TR></TABLE>
for a bump in compression he could select a set of OE pistons from another d, such as p29 or something-----
#9
Re: (builthatch)
dude here's some advice, drop the d-16 and why dont you get some B series motor? sounds like some extra horse power, reliable, and you get more street credit dawg, haha im kidding, you got to think what is more worth your money
#10
MiG-21 superfan
Join Date: Mar 2001
Location: near the ocean, Moderator City, NJ
Posts: 8,628
Likes: 0
Received 3 Likes
on
3 Posts
Re: (S13sGA2DUMP)
full d16z6 build for $2500 with 90% OE honda parts that will net you around 20-25 more whp and 20+ more ft/lbs than a b16 swap...or, b16 swap with all the associated parts for $2500.....
#11
Re: (builthatch)
d16z6 build for $2500...ill tell you what, ill do that build for $1500, all day long, any day of the week including God's day.
i built a d16z6 for a thousand. it runs nearly 14:1, eats up b, h, and k series engines with a jg engine dynamics cam, and TB.
i love b series, but there is a lot to be done with a d16. but the next trick is droppin a fully built turbo h22a runnin 11:1 with 16lbs into a 1988 crx si shell.
i built a d16z6 for a thousand. it runs nearly 14:1, eats up b, h, and k series engines with a jg engine dynamics cam, and TB.
i love b series, but there is a lot to be done with a d16. but the next trick is droppin a fully built turbo h22a runnin 11:1 with 16lbs into a 1988 crx si shell.
#12
MiG-21 superfan
Join Date: Mar 2001
Location: near the ocean, Moderator City, NJ
Posts: 8,628
Likes: 0
Received 3 Likes
on
3 Posts
Re: (CallMeJesus)
to make over 150 whp reliably out of a sohc vtec, I have found you need...
p29's @ .5mm over with rings- 250
Crower 2 or 3 cam- 325
Springs/ TI rets- 320
ARP rod bolts- 50
Bore, mill/deck, balance, shot-peen rods, valve job- 500
portwork- free, if you know what you are doing
or
portwork- 500
bearings, gaskets, WP/t-belt- 250
Clutch- 325
y8 intake mani- 50
BBK TB- 250
or Type R TB- 150
Header- 300-600
PowerFC- 650+250dynotime
or
Hondata- 295+250 dynotime
or
chipped p28- 150
This is assuming you already have the complete engine and it is not damaged, your fuel pump is up to the task, your injectors are balanced/ flowing properly, and already have obd1 harness plugs so you don't need jumper harness....
PS- sure, you could cut many many corners, but every extra mile you get out of the setup is worth it as is every little HP...
p29's @ .5mm over with rings- 250
Crower 2 or 3 cam- 325
Springs/ TI rets- 320
ARP rod bolts- 50
Bore, mill/deck, balance, shot-peen rods, valve job- 500
portwork- free, if you know what you are doing
or
portwork- 500
bearings, gaskets, WP/t-belt- 250
Clutch- 325
y8 intake mani- 50
BBK TB- 250
or Type R TB- 150
Header- 300-600
PowerFC- 650+250dynotime
or
Hondata- 295+250 dynotime
or
chipped p28- 150
This is assuming you already have the complete engine and it is not damaged, your fuel pump is up to the task, your injectors are balanced/ flowing properly, and already have obd1 harness plugs so you don't need jumper harness....
PS- sure, you could cut many many corners, but every extra mile you get out of the setup is worth it as is every little HP...
#14
Honda-Tech Member
Thread Starter
Re: d16 rebuild kit (NA tangy_b16)
wow this topic is OLD>
I just swapped in a gsr
Wish i would've stayed sohc (moneywise)
or bought another car and built a motor as the money was availbale.
just my .02
I just swapped in a gsr
Wish i would've stayed sohc (moneywise)
or bought another car and built a motor as the money was availbale.
just my .02
#15
re: dzminiz's D16 Engine Rebuild Kit
Hey guys. yeah this is really old post but i thought i just share it anyways for the people that are still looking for a rebuild kit. http://ebay.to/2FEhEWY Bought this rebuild kit and it did the job for what i need it for.
Thread
Thread Starter
Forum
Replies
Last Post
whattheduck
Transmission & Drivetrain
7
08-06-2023 11:14 AM