Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 5
1
2
3
Last »
Search: Posts Made By: roll8221
Showing results 1 to 25 of 116
Search took 0.20 seconds.
Forum: Tech / Misc
12-22-2018, 04:09 AM
Replies: 5
Views: 2,862
Posted By roll8221

re: B18b1 turbo swap Overheating. Shop is piss poor at diagnosing issue, now what?

Forgot to update. So i let the guy replace the radiator after i suggested it could possibly be the head gasket and he basically ignored it and assured me it was the radiator.... $800 later and it...
Forum: Honda Accord (1990 - 2002)
12-22-2018, 04:04 AM
Replies: 0
Views: 835
Posted By roll8221

94 accord no speedo, heater, door locks or interior lights

94 accord, like the title says no speedometer, heater, door locks, or interior lights. The dash lights still work, the heater blows but not hot and the interior lights dont work. Ive searched to look...
Forum: Tech / Misc
09-27-2018, 11:14 PM
Replies: 5
Views: 2,862
Posted By roll8221

B18b1 turbo swap Overheating. Shop is piss poor at diagnosing issue, now what?

96 coupe with b18 turbo swap. less than 6000 miles on motor and most other parts including radiator specifics are in my posts somewhere. So I'm having a overheating issue after it gets to temp....
Forum: Tech / Misc
09-19-2016, 05:50 PM
Replies: 4
Views: 1,778
Posted By roll8221

Re: Overheating b18

Thermostat or temp sensor were my other two thoughts... Wondering also if i could try to take out the thermostat for a bit to see if jt improves and/or test the thermostat... I read somewhere that if...
Forum: Tech / Misc
09-19-2016, 05:47 PM
Replies: 4
Views: 1,778
Posted By roll8221

Re: Overheating b18

Not yet... Would like to narrow it down and make sure my thinking is in the right direction before i start throwing mo ey at it.... Id like to fix the drivability issue then move on the the next...
Forum: Tech / Misc
09-19-2016, 12:52 PM
Replies: 4
Views: 1,778
Posted By roll8221

Overheating b18

boosted b18 overheating on acceleration... sputtering on deceleration found broken flex pipe which is before the o2 sensor.... my thinking would be leak pre o2 sensor would cause it to run rich but...
Forum: Tech / Misc
07-25-2016, 12:21 AM
Replies: 9
Views: 676
Posted By roll8221

Re: Weird interm overheating issue.

Hard to tell if fan is turning on because im driving and can tell. Afraid to stop and check because of lack of air flow... Thinking ill start with the thermostat...
Forum: Tech / Misc
07-23-2016, 05:19 AM
Replies: 9
Views: 676
Posted By roll8221

Weird interm overheating issue.

I have a weird overheating issue.. I have a full list of mods to my motor but in the short, its a built b18c1 with a precision 6262 and an AEM EMS. If any other mods are needed to help let me know....
Forum: Engine Management and Tuning
01-28-2016, 09:55 PM
Replies: 1
Views: 917
Posted By roll8221

AEM - disconnected battery for a while, now having problems

Have an aem series 2 ems and I disconnected the battery for a while because the cold killed the last battery. Now the motor wont go past 2k rpms... almost like the rev limiter is on and then the...
Forum: Forced Induction
11-04-2015, 03:35 PM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

Thanks, ill check him out...
Forum: Forced Induction
11-02-2015, 08:16 PM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

Did a Compression test on the motor as well, was dead nuts even all the way across...also, i was told the cutoff was put at 22psi but according to the boost gauge its only producing 12-15psi at full...
Forum: Forced Induction
11-02-2015, 08:00 PM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

Log style manifold, 3" downpipe, 3" exhaust, no cat...
Forum: Honda Prelude
09-24-2015, 06:03 AM
Replies: 1
Views: 573
Posted By roll8221

Re: no vtech/ loss of power in higher rpm after 5 speed swap

Forgot to mention, the only CEL code im getting is #92 which has to do with the evap system.
Forum: Honda Prelude
09-24-2015, 06:03 AM
Replies: 1
Views: 573
Posted By roll8221

no vtech/ loss of power in higher rpm after 5 speed swap

Did a 5 speed swap on a 99 prelude, Car runs and drives but when accelerating it seems like when vetch should be kicking in it loses all power and no vetch. It had a surging idle which I seemed to...
Forum: Honda Prelude
09-24-2015, 05:13 AM
Replies: 4
Views: 6,951
Posted By roll8221

Re: Automatic to Manual Transmission Swap, any problems?

I know its kind of an old thread but what would cause the vetch to not work and not rev past 6500 rpm as stated above, I'm currently having that issue...
Forum: Tech / Misc
06-09-2015, 06:47 AM
Replies: 8
Views: 1,123
Posted By roll8221

Re: crank case vantilation and air/fuel ratio...

396502
I have 2 an10 fittings coming off the valve cover us the 2 off the back of the block. So basically i need to add a line to the intake side of the turbo and put the black box back on? Im not...
Forum: Forced Induction
06-08-2015, 01:19 PM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

I also noticed after some time, some very fine bubbles were coming through the gasket between the throttle body and intake and the bolts securing it but seemed almost insignificant. could a leak that...
Forum: Forced Induction
06-08-2015, 01:15 PM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

I used a 2.5 inch coupler with a can on one end and the other end connected to the charge pipe right off of the cold side of the turbo. I put a tire valve stem in the end of the can, hooked a...
Forum: Forced Induction
06-08-2015, 05:27 AM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

Ive done a leak test on the charge pipe/intake but not the engine itself. I have stopped driving it, until i find out the most current issue, but other than that the tuner said it was safe to drive
Forum: Forced Induction
06-08-2015, 03:32 AM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

I have recently installed a oil catch can with breathers to decrease my crank case pressure. After installing though, I noticed it doesn't have quite as much pull when accelerating and a little bit...
Forum: Tech / Misc
06-08-2015, 03:25 AM
Replies: 8
Views: 1,123
Posted By roll8221

Re: crank case vantilation and air/fuel ratio...

Pcv has been totally deleted... No valve.... replaced black box with plug and installed the two fittings in the back of the block...
Forum: Tech / Misc
06-07-2015, 05:10 PM
Replies: 8
Views: 1,123
Posted By roll8221

crank case vantilation and air/fuel ratio...

I have recently installed a oil catch can with breathers to decrease my crank case pressure. After installing though, I noticed it doesn't have quite as much pull when accelerating and a little bit...
Forum: Forced Induction
06-06-2015, 07:38 AM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

Going to check.for boost leak in the tomorrow a.m. took it out for a run today and think i lost boost almost completely. A/f ratio went so lean it wouldnt read part of the time too... have to rig up...
Forum: Forced Induction
06-04-2015, 08:47 PM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

Yeah, i travel a couple hours to get it tuned there. I did some homework before bringing it. Realstreet and jay in particular hold records for the s2000 and the ariel atom??? They also have alot of...
Forum: Forced Induction
06-04-2015, 11:52 AM
Replies: 81
Views: 8,356
Posted By roll8221

Re: was expecting more than 350hp...

I talked to the tuner today, says to look into a set of itr cams and a set of gears and come back for a re-tune. Not sure if it makes a difference or not cause im ignant, but i didnt have proper...
Showing results 1 to 25 of 116
 
Page 1 of 5
1
2
3
Last »


 
Forum Jump


All times are GMT -8. The time now is 08:48 AM.