Notices
 
Search: Posts Made By: SirFerret
Showing results 1 to 25 of 111
Search took 0.30 seconds.
05-18-2018, 05:53 PM
Replies: 0
Views: 647
Posted By SirFerret

2000 CR-V Engine Dead at 205k

So my beloved CR-V is pretty much dead right now with a ruined crankshaft end from a loose/failed crankshaft bolt. Heard a terrible vibrating noise from the engine while just driving around as usual,...
02-13-2018, 07:58 AM
Replies: 0
Views: 2,719
Posted By SirFerret

Is the JDM fender mirror adjustable? (1st gen)

So I have finally tracked down a JDM front clip, and currently have the bumper and left fender w/fender mirror installed for testing fitment. While the fender mirror looks cool cosmetically, its not...
02-13-2018, 07:44 AM
Replies: 9
Views: 5,563
Posted By SirFerret

Re: 00 CRV - Drum Brakes Squeak, especially in Reverse

Jack up the rear end, and give the tire/wheel combo a good shake down. If there is any bit of play then something is loose or the bearing is bad. Even the slightest bit of movement between where the...
10-30-2015, 03:26 PM
Replies: 1
Views: 916
Posted By SirFerret

Anybody interested in CR-V heated mirror mod?

So I am about halfway through retrofitting the heated mirror glass from the 2nd Gen CR-V into my 1st Gen. Getting the glass into the housing was pretty easy, but this wiring is really tough. The...
09-30-2015, 02:02 PM
Replies: 17
Views: 11,636
Posted By SirFerret

Re: Proper gen 1 HID retrofit?

So I finished the project, and have been driving and adjusting them for the past week or so. I am finally happy with everything, and will start writing the DIY today. The on-road results are...
09-30-2015, 01:55 PM
Replies: 13
Views: 3,028
Posted By SirFerret

Re: Spark plugs ? really?

For iOS you need to get a Wifi code scanner, the bluetooth ones only work with Android.

As to the original question, see if you can go to your nearest auto parts store, as they usually pull the...
09-22-2015, 06:51 PM
Replies: 12
Views: 3,914
Posted By SirFerret

Re: Seized lug nut

Both of my studs were replaced using the "cheat" way, which means grinding down the head of the new stud a bit so it can be slid past the knuckle. Now if you already have the tools to replace the...
09-18-2015, 04:44 PM
Replies: 17
Views: 11,636
Posted By SirFerret

Got them installed!

So I got the lights all installed and wired up. Unfortunately I had forgotten to epoxy the shrouds to the projectors, so when I closed to hood to go for a test drive they fell off lol :thud:. Will...
09-17-2015, 02:55 PM
Replies: 17
Views: 11,636
Posted By SirFerret

Proper gen 1 HID retrofit?

Will do. I wasn't sure what color to go with either, but decided on the chrome to keep with the look of the car. In my opinion the flat black wouldn't go with my build, but I'm sure it would look...
09-17-2015, 11:39 AM
Replies: 17
Views: 11,636
Posted By SirFerret

Got the goods!

UPS has just delivered the goods! Everything checks out and is ready to install! So far I am super impressed with this kit. All these pieces are metal (where applicable) and have that "quality heft"...
09-17-2015, 03:29 AM
Replies: 12
Views: 3,914
Posted By SirFerret

Re: Seized lug nut

If you have to take it out by force, try using an impact wrench before pulling out the breaker bar. There is a lot less chance of breaking the stud off, and possibly being able to save the threads,...
09-15-2015, 04:00 PM
Replies: 17
Views: 11,636
Posted By SirFerret

Re: Proper gen 1 HID retrofit?

Hey nice set up you have there. I like the shroud you picked, as it blends in with the chrome and looks as factory as its going to get. I ordered a similar shroud, as I hope to have the projector...
09-15-2015, 02:24 PM
Replies: 2
Views: 2,239
Posted By SirFerret

Re: 2006 Honda Odyssey EX-L AC Problems

Make sure to check the relay that controls the AC compressor clutch. That relay and also the AC condenser fan relay are know to fail and cause AC problems. I had this happen in my 08' Odyssey, after...
09-15-2015, 02:19 PM
Replies: 17
Views: 11,636
Posted By SirFerret

Re: Proper gen 1 HID retrofit?

All the parts were shipped earlier this morning, so hoping I can do the retrofit this weekend. I will keep you all posted on how it goes. If everything goes well, hoping to get a nice write up made...
09-15-2015, 02:17 PM
Replies: 1
Views: 1,526
Posted By SirFerret

Re: 2005 CR-V wheel size confirmations

I don't believe that the center bore matters, as the CR-V has lug centric wheels. This means that the wheel is centered via the lug nut acorns. This is different than say my F-150 that has hub...
09-14-2015, 06:09 PM
Replies: 17
Views: 11,636
Posted By SirFerret

Proper gen 1 HID retrofit?

So I was helping a bud retrofit/convert his NC Miata halogen projectors to HID projectors, and for fun I Googled "crv hid retrofit" and found a few threads of people swapping in Morimoto D2S retrofit...
03-06-2015, 02:31 PM
Replies: 25
Views: 42,771
Posted By SirFerret

Re: Possible to put fog on 1st Gen crv like the jdm/edm bumper?

I gave up on tracking down a JDM bumper, so I just installed a Westin bulbar. They are readily available for about 100-150 buck w/brackets. I have a pair of Hella 500 fogs on the bottom, and a pair...
03-06-2015, 02:25 PM
Replies: 9
Views: 1,258
Posted By SirFerret

Re: just bought it and it's misfiring

Ah thats a really important one I missed! Vacuum leaks could describe exactly what is happening to you. Also check the PCV valve and all it's connecting hoses. They are a maintenance item that are...
03-06-2015, 12:11 PM
Replies: 9
Views: 1,258
Posted By SirFerret

Any check engine lights? A legit misfire would...

Any check engine lights? A legit misfire would throw a code as to which cylinder is the culprit.

First easy place to check is the spark plugs and gap. At 200k, there is a good chance they are in...
01-14-2015, 11:57 AM
Replies: 21
Views: 82,206
Posted By SirFerret

Fixed it!

Sorry to bring back an old post, but I have some new info that may be useful to some.

It's been an abnormally cold winter here so far, and the grinding cold start noise was occurring more and...
12-01-2014, 05:23 PM
Replies: 10
Views: 6,279
Posted By SirFerret

Re: 1st Gen Block Heater?

So Benardi did kick me back as "discontinued" like I thought it would. The only other options I could find are a "ZeroStart" brand one that mounts in the stock location, or the kind that goes inline...
11-29-2014, 02:34 PM
Replies: 10
Views: 6,279
Posted By SirFerret

Re: 1st Gen Block Heater?

Hmmm Bernardi Honda let me order one from online. Hopefully it doesn't kick back later as "discontinued". :scared:
11-29-2014, 02:24 PM
Replies: 10
Views: 6,279
Posted By SirFerret

1st Gen Block Heater?

Hey all,

I have been looking to put a block heater into my 00' CR-V to help reduce wear and tear on the engine on my short trips around town. Also faster cabin heat will be nice too! :thumbup:
...
11-20-2014, 06:47 AM
Replies: 1
Views: 4,866
Posted By SirFerret

Re: Gen 1 CR-V Cruise Control Bulb Part Number?

So I have answered my own question, and will post my findings here for future reference.

The original part number I mentioned is not correct. No idea where he pulled that number from lol. Was only...
11-18-2014, 02:21 PM
Replies: 1
Views: 4,866
Posted By SirFerret

Gen 1 CR-V Cruise Control Bulb Part Number?

Hey all,

One of the bulbs inside my Cruise Control switch has burnt out on my '00 CR-V. I looked up the parts diagram as usual, and found something strange. The part is listed in the diagram as...
Showing results 1 to 25 of 111
 


 
Forum Jump


All times are GMT -8. The time now is 12:52 AM.