Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: boostedgeezer
Showing results 1 to 25 of 71
Search took 0.20 seconds.
Forum: Engine Management and Tuning
10-15-2013, 11:04 PM
Replies: 19
Views: 4,049
Posted By boostedgeezer

Re: what oil do u use after braking in your motor

I run non detergent 30w, get it up to temp, drain it, change filter. good quality 10w-30 with bg oil additive(loaded with zinc, and not easy to obtain, i get it from my buddie who works for toyota),...
Forum: Drag Racing
08-28-2013, 05:20 PM
Replies: 14
Views: 1,243
Posted By boostedgeezer

Re: What's a good engine

4afe toyota motor would be great in that thing. Probably get about 40mpg!!!!!!!!!!
Forum: Drag Racing
08-25-2013, 12:04 AM
Replies: 27
Views: 3,601
Posted By boostedgeezer

Re: whos NOT running water threw the intake manifold?

The 5/8 heater hose that normally goes to the heater core??? I would assume that would be the only one you have running to the backside of the thermostat housing, And if so, that shouldnt be a...
Forum: Drag Racing
08-24-2013, 10:56 PM
Replies: 27
Views: 3,601
Posted By boostedgeezer

Re: whos NOT running water threw the intake manifold?

Im running the hose from the intake manifold to the water jacket and have the outlet from the side of the head blocked off. Im assuming u have the heater hose from the side of the head running to...
Forum: Drag Racing
07-29-2013, 04:43 PM
Replies: 42
Views: 14,175
Posted By boostedgeezer

Re: MoTeC M84 ecu

Dont know who is doing your harnes and relay panel but Joel @ racespec is very familiar with motec products and he will be able to guide you in the right direction as to what logger to use. Who ever...
Forum: Drag Racing
07-28-2013, 03:15 PM
Replies: 109
Views: 20,568
Posted By boostedgeezer

Re: Ray from EggyRacing PB StockSleeves!!!

Random question, what type of ignitor are you guys running?? Assuming that is the little black box that is zip tied to the msd box????
Forum: Tech / Misc
07-28-2013, 11:53 AM
Replies: 26
Views: 1,836
Posted By boostedgeezer

Re: harder to start when warm.

Its time to take a look at your ignition system. Pull the cap check the rotor, peek at the coil if you can. Most of the time when these cars would come into my shop with customers complaining of an...
Forum: Engine Management and Tuning
07-24-2013, 01:11 PM
Replies: 25
Views: 76,757
Posted By boostedgeezer

Re: The philosophy of how we retard ignition timing in boost: to what end?

Notice how Jeff himself didnt comment at all in that post??? Because those are the same questions that a dyno will answer, all part of finding MBT. Every setup is different, so u really cant say...
Forum: Engine Management and Tuning
07-24-2013, 04:27 AM
Replies: 25
Views: 76,757
Posted By boostedgeezer

Re: The philosophy of how we retard ignition timing in boost: to what end?

Go to a dyno and you will see exactly where your timing needs to be. You are asking very general questions as far as how much to retard. We have no idea what kind of timing number are in your table,...
Forum: Drag Racing
06-06-2013, 01:33 PM
Replies: 27
Views: 2,817
Posted By boostedgeezer

Re: Integra on jack stands, no load, making horrible noise and shaking the motor/tran

If you took it on a 60 mile ride with no noise and no shifting or drivabilitly issues, what exactly is the problem??? im kind of not following you here.
Forum: Engine Management and Tuning
06-05-2013, 05:30 PM
Replies: 9
Views: 1,192
Posted By boostedgeezer

Re: What should I be expecting with new basemap/chip?

I cant believe people still ask this question. A basemap is good to drive the car to a TUNER, thats about it. Do it right or dont do it at all.
Forum: Tech / Misc
05-19-2013, 05:17 PM
Replies: 8
Views: 3,010
Posted By boostedgeezer

Re: what caused my cracked ringland(s)

At this point your best bet is going to be getting the motor back together, get yourself a wideband for the future and get it back to the dyno to make sure everything is still happy. While it is...
Forum: Tech / Misc
05-19-2013, 11:24 AM
Replies: 8
Views: 3,010
Posted By boostedgeezer

Re: what caused my cracked ringland(s)

Thats detonation my friend. At 10-13 psi ive had customers cars last YEARS with stock pistons and rods if the tune is on the money. Shouldnt have happened at that power level. Not that its...
Forum: Engine Management and Tuning
05-18-2013, 03:58 PM
Replies: 3
Views: 1,095
Posted By boostedgeezer

Re: Stone gasket

If you look at the small writing under where it says Stone it says Ishino which is and oem manufacturer that makes the oem Honda gasket. Use them on most of my motors i build. Never have had any...
Forum: Engine Management and Tuning
05-17-2013, 05:33 PM
Replies: 17
Views: 1,390
Posted By boostedgeezer

Re: Wiring harness?!?

not to sound like a dick but you sound like you are all over the place with these questions. Do yourself a favor and email joel@strdonline.com and tell him EXACTLY what your set up constists of and...
Forum: Drag Racing
05-11-2013, 05:12 PM
Replies: 47
Views: 4,604
Posted By boostedgeezer

Re: quest for 10's stock gsr true street car

Bone stock motor? Also, what type of shifter is that????
Forum: Drag Racing
05-02-2013, 06:06 PM
Replies: 48
Views: 5,676
Posted By boostedgeezer

Re: installing my last head gasket before throwing in the towel tomorrow..tips/tricks

We lifted a d series head on the dyno on a d series build not too long ago. Pulled the head off and sent it to the machine shop. They milled it for the second time as this head was also overheated...
Forum: Drag Racing
04-17-2013, 01:37 PM
Replies: 556
Views: 92,233
Posted By boostedgeezer

Re: 8.50 and slower roll cage!!!! JUNK.

They know about you?? Like who the fuck you are??? First off Hondas are me too cars bro. 9.90 is nothing out of the ordinary for a turbo honda. Second, all they know about you is you are part of...
Forum: Drag Racing
04-01-2013, 01:28 PM
Replies: 12
Views: 2,172
Posted By boostedgeezer

Re: stolen kpro

I had a similar issue at my shop, and although i have business insurance, since the car was outside of my shop at the time it was broken into, his car insurance covered it. May want to see if the...
Forum: Drag Racing
03-26-2013, 08:58 AM
Replies: 11
Views: 2,242
Posted By boostedgeezer

Re: 651whp b series trans options

Made 630 on a dynojet. Bone stock gsr trans stock diff oem honda fluid and a comp stage 5. 30 hits last season. Pulled it apart last week to do a Mfactory diff and a twin disc and the thing looked...
Forum: Drag Racing
03-24-2013, 10:50 AM
Replies: 22
Views: 3,556
Posted By boostedgeezer

Re: Post your experiences with PTE wastegates....

39mm two bolt on a d series street car. not a single isssue at all. Its been on there about 6 months now.
Forum: Drag Racing
03-04-2013, 02:49 PM
Replies: 32
Views: 2,457
Posted By boostedgeezer

Re: my race car has a gremlin help

Def not impossible. Just had a customer with a 1995 civic ex just a regular bone stock car in a crank no start with no signal and no check engine light on or codes stored. Mickey Mouse distributor...
Forum: Drag Racing
03-04-2013, 04:46 AM
Replies: 32
Views: 2,457
Posted By boostedgeezer

Re: my race car has a gremlin help

Being that you are loosing injector pulse, i would see what you are missing, either signal from the ecu or power. If you are missing power i would go towards that resistor box or wiring. If you are...
Forum: Drag Racing
02-26-2013, 05:57 PM
Replies: 3
Views: 810
Posted By boostedgeezer

Re: Need help- Which Cams?

[QUOTE=KUSSY;48506436]Hi guys i have a 91 Crx My goal is to make over 600- 700whp. I have sleeved built 84mm ls vtec with springs, retainers, stainless valves stock us gsr cams. Got golden eagle...
Forum: Engine Management and Tuning
02-11-2013, 05:47 PM
Replies: 12
Views: 1,270
Posted By boostedgeezer

Re: 97 GSR swap in a 95 Dx coupe

For your 21 vtec solenoid code, check for continuity between Pin a4 at the ecu and your connector at your solenoid, most likely a wiring issue. As for your code 1, you do have a 4 wire o2 sensor...
Showing results 1 to 25 of 71
 
Page 1 of 3
1
2
3


 
Forum Jump


All times are GMT -8. The time now is 12:21 AM.