Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: tim73
Showing results 1 to 25 of 500
Search took 0.46 seconds.
Forum: Honda CR-V & Element
10-22-2019, 07:10 AM
Replies: 20
Views: 17,942
Posted By tim73

Re: JDM 4WD transmission swap-able?

I used the JDM dizzy...started...ran and idles perfect.
Forum: Honda CR-V & Element
10-22-2019, 07:05 AM
Replies: 4
Views: 1,638
Posted By tim73

Re: Jdm B20b Ecu Help

I got the JDM engine/trans installed last night and ran it a little bit. I used the USDM intake and exhaust manifold, and it fired right up, and idled correctly. It did throw two codes for CKF, so...
Forum: Honda CR-V & Element
10-21-2019, 06:07 AM
Replies: 3
Views: 8,748
Posted By tim73

Re: doing the ckf bypass on crv

777777,
Did you ever get it straightened out? Thanks! Did you use JDM dizzy or put the USDM one on? Also, did you use the JDM intake manifold, or go with the USDM? I got my JDM engine installed...
Forum: Honda CR-V & Element
10-16-2019, 12:52 PM
Replies: 4
Views: 1,638
Posted By tim73

Re: Jdm B20b Ecu Help

this post was from last month...so im probably wasting my breath. But I heard on the JDM's you have to use the usdm intake and exhaust manifold. Looks like the JDM intake manifold is installed. I...
Forum: Honda CR-V & Element
10-16-2019, 12:47 PM
Replies: 3
Views: 3,530
Posted By tim73

Re: 2012 crv driver seat . Help a girl out.

theyre normally held in by four bolts. Underneath is at least one wiring harness to release. Id undue the bolts first, leave the wiring connected...so you can still move it forward and...
Forum: Honda CR-V & Element
10-16-2019, 12:45 PM
Replies: 20
Views: 17,942
Posted By tim73

Re: JDM 4WD transmission swap-able?

Thanks a lot pegleg. What did you mean buy hondata? Thanks! I just bought a jdm engine and awd tranny...theyre on the engine stand right now...swapping over intakes exhaust sensors etc. Hopefully...
Forum: Honda CR-V & Element
10-15-2019, 11:20 AM
Replies: 20
Views: 17,942
Posted By tim73

Re: JDM 4WD transmission swap-able?

pegelbert,
So if I understand correctly, you installed the new b20b engine, with jdm transmission and had to swap out the shift position sensor from the usdm one? Which that's the sensor under the...
Forum: Hybrid / Engine Swaps
10-15-2019, 11:09 AM
Replies: 25
Views: 68,290
Posted By tim73

Re: automatic jdm trans and usdm auto trans the same?

drewshondashop, so I understand you replaced the ecu with the 37820-PHK-901, and you've had no problems? I don't have emmissions where I live, so im not too terribly concerned with that. But I do...
Forum: Honda Accord (1990 - 2002)
02-28-2018, 02:24 PM
Replies: 6
Views: 2,702
Posted By tim73

Re: 97 Accord LX V6 timing belt and water pump

I've never done the 2.7, but I've done the 2.2, 2.3 and the 3.0. Is there any way the ring the sensor is looking at is flipped? I'm not sure it's possible, just thinking out loud. Also, double...
Forum: Honda Accord (1990 - 2002)
02-28-2018, 02:14 PM
Replies: 10
Views: 2,009
Posted By tim73

Re: New guy, 2002 Accord 3.0L mysterious bucking (trying to post again)

Have you tried live data on your scanner? Make sure ect is right, and the engine goes into closed loop ok? Also are the upstream o2 sensors equal and responsive?
Forum: Honda Accord (1990 - 2002)
02-28-2018, 01:24 PM
Replies: 5
Views: 692
Posted By tim73

Re: 96 accord stumper

Changed out fuel filter, just cause it looked old. Removed the injector rail...to check if while cranking, injectors were shooting fuel. They were, I was worried maybe they were stuck open. But...
Forum: Honda Accord (1990 - 2002)
02-28-2018, 11:27 AM
Replies: 5
Views: 692
Posted By tim73

Re: 96 accord stumper

Fpr is out of the picture. I removed hose from side of rail(where it attaches to banjo bolt fitting). Hooked up my test gauge via banjo bolt fitting.
Forum: Honda Accord (1990 - 2002)
02-27-2018, 07:40 PM
Replies: 5
Views: 692
Posted By tim73

Re: 96 accord stumper

No, but it hasn't really ran. I did hook up my obd2 scanner and put on live data. Shows the ect is in the ballpark. Gonna try the coil tomorrow. See if swapping a new one makes any difference. ...
Forum: Honda Accord (1990 - 2002)
02-27-2018, 01:06 PM
Replies: 5
Views: 692
Posted By tim73

96 accord stumper

Hi guys, I got a 96 accord Lx f22b2(non-vtech). So, it turns over fine and is trying to fire, just won't. Checked compression, 190 all four cylinders, checked coil, nice bright spark, checked each...
Forum: Honda Accord (1990 - 2002)
02-22-2016, 08:17 PM
Replies: 5
Views: 2,813
Posted By tim73

Re: Help for noob please!

Worse case scenario, you can loosen up cam cap bolts. Lift off, but don't remove(Allowing all valves to go closed...then you can set everything to TDC, both cam and crank. Then re-torques cam caps.
Forum: Honda Accord (1990 - 2002)
02-22-2016, 07:47 PM
Replies: 4
Views: 4,829
Posted By tim73

Re: 1999 Honda Accord crank, but won't start

If you have(and are sure) you have spark and fuel, then it sounds like timing and or no compression. Did you slip and or break a timing belt?
Forum: Honda Accord (1990 - 2002)
02-05-2016, 07:26 AM
Replies: 5
Views: 1,234
Posted By tim73

Re: Cel blinking p1399 and low compression on cylinder 3

Last time I had a burnt valve on a f22, was due to carbon buildup on the piston. The valve made contact and it ate a hole in the side of it. Either way, new head...head gasket...happy days.
Forum: Honda Accord (1990 - 2002)
01-20-2016, 11:24 AM
Replies: 10
Views: 43,095
Posted By tim73

Re: 1996 Honda Accord 2.2, 4cy, camshaft position sensor

I had the ICM go out on my 97. The auto parts store will test some Ignition modules...and I think the Honda is one they can test. I just cant remember though...Old age:) But I can tell you, if...
Forum: Honda Accord (1990 - 2002)
01-20-2016, 10:37 AM
Replies: 11
Views: 11,013
Posted By tim73

Re: Heater turns off by itself

When the Air stops coming out, you need to see if the fan quit, or not. If it did(And it sounds like that is the case) Then most likely...power to the blower was interrupted or the motor is no good.
Forum: Honda Accord (1990 - 2002)
01-17-2016, 09:18 PM
Replies: 3
Views: 2,595
Posted By tim73

Re: Front balancer belt pulley bolt head snapped off

If you can get to it(Which it sounds like you cant) I would weld a smaller bolt to it...then turn that bolt out. Or you can drill a hole in it(Its pretty hard steel...so use a sharp bit, go slow and...
Forum: Honda Civic / Del Sol (1992 - 2000)
01-17-2016, 02:07 PM
Replies: 14
Views: 934
Posted By tim73

Re: 95 delsol b16a3 questions

Was able to pick up a complete d16z6, will see about installing it in the next week or so. Thanks!
Forum: Honda Civic / Del Sol (1992 - 2000)
01-11-2016, 06:00 PM
Replies: 14
Views: 934
Posted By tim73

Re: 95 delsol b16a3 questions

Sorry yeah, d16z6. New to civics.
Forum: Honda Civic / Del Sol (1992 - 2000)
01-11-2016, 12:01 PM
Replies: 14
Views: 934
Posted By tim73

Re: 95 delsol b16a3 questions

So, I too yalls advise. Looked in spark plug holes. #2 cylinder isn't moving. So looks like the connecting rod/pin or something is broke. No idea what the cylinder wall looks like. I'll be...
Forum: Honda Accord (1990 - 2002)
01-10-2016, 08:10 PM
Replies: 19
Views: 2,243
Posted By tim73

Re: 92Accord EX thoughts

Update....So, I eventually finished the car. I used the f22a1 block and head. Used the a6 cam and springs. Plus the a6 intake and exhaust. Car runs pretty good. New timing belt, water pump head...
Forum: Honda Accord (1990 - 2002)
01-10-2016, 03:11 PM
Replies: 17
Views: 9,297
Posted By tim73

Re: 97 accord heater woes

To flush the heater, remove the heater hose with the valve in it at the head. Disconnect the hose coming from the core at the firewall(the other end comes off that pipe that runs along the back of...
Showing results 1 to 25 of 500
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 01:09 PM.