Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 2
1
2
Search: Posts Made By: JoeBull
Showing results 1 to 25 of 47
Search took 0.27 seconds.
Forum: Honda Accord (1990 - 2002)
09-01-2010, 05:05 PM
Replies: 2
Views: 802
Posted By JoeBull

Strut Bars

I read somewhere that a lower front bar did more than an upper front bar (strut tower brace). Has anyone used a lower front bar? I have a three piece bar set from Ebay (front upper, rear upper and...
Forum: Honda Accord (1990 - 2002)
08-29-2010, 11:12 AM
Replies: 3
Views: 687
Posted By JoeBull

Re: Lower Shock Mounts

Do you have a part # for the rears?
Forum: Honda Accord (1990 - 2002)
08-28-2010, 05:26 PM
Replies: 3
Views: 687
Posted By JoeBull

Lower Shock Mounts

Has anyone replaced the lower shock mounts? Why do they have a metal sleeve? The new energy suspension front ones don't have a metal sleeve, but they don't make them for the rear. How do you get the...
Forum: Honda Accord (1990 - 2002)
08-10-2010, 04:57 PM
Replies: 0
Views: 717
Posted By JoeBull

Fast Idle adjusting

I just cleaned my egr runner, egr valve, IACV, FITV and throttle body a few days ago. I bled the coolant last night it took almost half a gallon. Today I started it and it ran great, but took a long...
Forum: Honda Accord (1990 - 2002)
07-31-2010, 06:41 PM
Replies: 30
Views: 3,185
Posted By JoeBull

Re: Honda Accord Maintenance Opinions

You don't have to change a head gasket unless it's blown. Is there coolant in your oil? Have you done a compression test?
Forum: Honda Accord (1990 - 2002)
07-31-2010, 12:54 PM
Replies: 4
Views: 6,911
Posted By JoeBull

Re: Gear knob fell off - where does the spring go?

My chrome button would pop out sometimes when changing gears usally after backing up. I sanded the rough tips of two little phillips heead screws and never had the problem again. Keep this in mind if...
Forum: Honda Accord (1990 - 2002)
07-31-2010, 12:45 PM
Replies: 4
Views: 1,471
Posted By JoeBull

Re: Cap and rotor replacement

You can just bump the motor, meaning turn the key and let it crank for just a second. The rotor only goes on one way. Before yot remove the wires draw a diagram of how the go. Check the old cap...
Forum: Honda Accord (1990 - 2002)
07-31-2010, 12:20 PM
Replies: 36
Views: 91,793
Posted By JoeBull

Re: f22b1 vtec, is it really that bad?

I didn't realize 96'-97' used the same block as 94'-95'. They use different intake manifolds, injectors and distributors. I haven't checked other parts.
Forum: Honda Accord (1990 - 2002)
07-29-2010, 07:58 PM
Replies: 36
Views: 91,793
Posted By JoeBull

Re: f22b1 vtec, is it really that bad?

I have a 94'EX F22B1 also. Does anyone know why Honda only made that motor for two years (94'-95' other years are different)? I think either it was too expensive to build and they went cheaper, or...
Forum: Honda Accord (1990 - 2002)
07-29-2010, 07:50 PM
Replies: 10
Views: 14,252
Posted By JoeBull

Re: 96 accord headers install

I found this the other day. https://honda-tech.com/forums/showthread.php?t=1786985&highlight=fiberglass+plastic&page=39 Two thirds down he installs a header, by the way its header not headers one...
Forum: Honda Accord (1990 - 2002)
07-28-2010, 10:49 PM
Replies: 6
Views: 3,961
Posted By JoeBull

Re: Interior Door Panels Accord Coupe

I just bought Bondo fiberglass resin and fiberglass cloth. I plan to cut the cloth to fit in one piece. Is cloth better than mat for this job? Will one layer be enough? Do I need to prep the panel?
Forum: Honda Accord (1990 - 2002)
07-28-2010, 01:05 PM
Replies: 18
Views: 40,368
Posted By JoeBull

Re: where to buy oem parts?

I already read that. I just want plugs that are better than stock and my engine is not modified. Denso wouldn't be cost effective for me. Thanks though.
Forum: Honda Accord (1990 - 2002)
07-28-2010, 10:09 AM
Replies: 18
Views: 40,368
Posted By JoeBull

Re: where to buy oem parts?

I just read about bosch plugs failing, mainly losing power over time. I'll probably replace mine in a couple months with NGK G-power platinum. I always thought NGK was japanese junk. As for Denso...
Forum: Honda Accord (1990 - 2002)
07-26-2010, 11:59 PM
Replies: 6
Views: 13,998
Posted By JoeBull

Re: Removing upper bolts on control arm ... URGENT

Dude, thanks. I bought mine in a kit from Ebay. The through bolts were not tight at all. I figured I would just take the old ones out and match the new ones to them the best I could. Any idea how to...
Forum: Honda Accord (1990 - 2002)
07-26-2010, 11:50 PM
Replies: 12
Views: 1,457
Posted By JoeBull

Re: 95 Accord Questions

Which one is the original and which one is the replacement? 51722-SV4-902, 51722-SV1-A12. They are both rubber 51722-SV4-901 is polyurethane. I am doing my front end and figured the bump stops would...
Forum: Honda Accord (1990 - 2002)
07-26-2010, 11:13 PM
Replies: 18
Views: 40,368
Posted By JoeBull

Re: where to buy oem parts?

HonBeer,What information or experiences do you have that prove Bosch platinums are bad? What info or experiences do you have that prove denso plugs are good? To quote Johnny Unitas "talks cheap"
Forum: Honda Accord (1990 - 2002)
07-26-2010, 03:55 PM
Replies: 6
Views: 13,998
Posted By JoeBull

Re: Removing upper bolts on control arm ... URGENT

sgraham, Do you know the adjusting procedure? I am changing both my upper control arms, struts and tie rods very soon. On a 94'EX coupe. I can't find any info on upper control arms other than the...
Forum: Honda Accord (1990 - 2002)
07-26-2010, 01:55 PM
Replies: 18
Views: 40,368
Posted By JoeBull

Re: where to buy oem parts?

I have a 94' EX also. I just tuned up mine with some 10mm vision wires I got on Ebay a while back ($43) Now you can get Accel's for $20, bosch platinum plugs ($1.50 ea. w/rebate) 3A Racing clear...
Forum: Honda Accord (1990 - 2002)
07-22-2010, 06:44 PM
Replies: 8
Views: 2,136
Posted By JoeBull

Re: plug wires

First off every little bit helps especially on a 4 cylinder. Second a bigger spark should reduce carbon deposits (via unburned fuel) in your cylinders and on your valves. Oh and third you can get...
Forum: Honda Accord (1990 - 2002)
07-22-2010, 04:11 PM
Replies: 2
Views: 672
Posted By JoeBull

Re: 92 accord axel replacement

If it's like my 94' Accord you probably have to take the knuckle off, then just pull out the old axle and push in a new one. much easier job than say changing brake rotors. WTF?
Forum: Honda Accord (1990 - 2002)
07-22-2010, 03:51 PM
Replies: 8
Views: 2,136
Posted By JoeBull

Re: plug wires

Where is the proof you speak of? I would go with Accel, all they do is ignition parts. Get a digital multimeter and test the Ohms on your old wires then test the Accels. Less resistance means bigger...
Forum: Honda Accord (1990 - 2002)
07-21-2010, 06:20 PM
Replies: 4
Views: 3,474
Posted By JoeBull

Re: exterior door handle stuck

Sorry the interior door handle came out of my VW. You should probably take your door apart clean and oil the handle mechanism and latch. Good Luck
Forum: Honda Accord (1990 - 2002)
07-21-2010, 11:02 AM
Replies: 89
Views: 108,742
Posted By JoeBull

Re: EGR port cleaning without using carb cleaner

Holmes it's not hard to get off the banjo, it's just like a brake hose end, but if it leaks you have to tighten it and could possibly break something. Why take something apart that you don't have to?...
Forum: Honda Accord (1990 - 2002)
07-21-2010, 10:46 AM
Replies: 4
Views: 3,474
Posted By JoeBull

Re: exterior door handle stuck

Dude, how is it stuck? I had a VW the door handle came out because the latch was corroded. Try spraying some WD-40 in the lacth, but if you feel ambitious take the door apart take the latch out and...
Forum: Honda Accord (1990 - 2002)
07-21-2010, 10:39 AM
Replies: 3
Views: 2,402
Posted By JoeBull

Re: Injector Warehouse

Yo, holmes. I got injectors from them last year, they look brand new. Check on Ebay too. I saw Chrome injectors for under $100 bucks, but couldn't use them because I have an EX VTEC motor (extra...
Showing results 1 to 25 of 47
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -8. The time now is 12:13 PM.