Notices
Search: Posts Made By: evo_s_uck
Showing results 1 to 16 of 16
Search took 0.32 seconds.
05-18-2009, 03:38 PM
Replies: 21
Views: 10,711
Posted By evo_s_uck

Re: smoking after rebuild???

does neone know a good motor build thread????
05-18-2009, 03:34 PM
Replies: 21
Views: 10,711
Posted By evo_s_uck

Re: smoking after rebuild???

i just ran the engine at an idle for a hour and monitored the vitals then i began to drive it to work which is only a 15 min drive and i never brang it above 4000 for the first 350 miles then it...
05-07-2009, 04:54 PM
Replies: 21
Views: 10,711
Posted By evo_s_uck

Re: smoking after rebuild???

im lost man should i just scrap the old engine and buy a new one... what do you guys do with your old engines and or engine parts plus i got the new stuff in the old engine and i dont really wanna...
05-06-2009, 03:45 PM
Replies: 21
Views: 10,711
Posted By evo_s_uck

Re: smoking after rebuild???

the block did get honed but not bored out so the standard size pistons are in there they are forged as well as the rods
05-06-2009, 03:42 PM
Replies: 21
Views: 10,711
Posted By evo_s_uck

Re: smoking after rebuild???

i did replace the head gaskit and the valve stem seals again after 150 miles on the fresh engine i considered that the head was warped but didnt further investigate it... i was thinking about getting...
05-06-2009, 03:31 PM
Replies: 21
Views: 10,711
Posted By evo_s_uck

Re: smoking after rebuild???

ya it seems like it smokes really bad at low rpms then at higher rpms it doesnt like after 4000 and it only does that when its warm... when its cold it doesnt smoke really at all... i took it to the...
05-04-2009, 03:01 PM
Replies: 21
Views: 10,711
Posted By evo_s_uck

Re: smoking after rebuild???

i checked the piston wall clearances to the specs they recomended and it was all good but if they were wrong or the rings were installed improperly wouldnt i get a bad compression reading i rechecked...
05-03-2009, 05:19 PM
Replies: 21
Views: 10,711
Posted By evo_s_uck

smoking after rebuild???

:scared:so my 00 civic si was leaking oil slowly like every 400 miles it would be low a quart and i thought it was the valve stem seals so i decided to rebuild the whole engine ( it had 175000 miles...
05-03-2009, 05:12 PM
Replies: 156
Views: 11,620
Posted By evo_s_uck

Re: Any good stories about weird things a previous owner did?

ya my buddy did the same shit n even drove to work and asked if it was normal to have swirl marks on the car after waxing it...
Forum: Tech / Misc
05-03-2009, 05:10 PM
Replies: 5
Views: 721
Posted By evo_s_uck

Re: question about plug wire placement...read

ya it doesnt even sound like itd start or run... does it run smootly or rattle
Forum: Tech / Misc
05-03-2009, 05:08 PM
Replies: 26
Views: 2,142
Posted By evo_s_uck

Re: Doing head gasket..what did I break? *pic*

deff use the moly shit they give you tho
05-03-2009, 05:04 PM
Replies: 15
Views: 14,406
Posted By evo_s_uck

Re: did valve adjustment but still ticking

ya i did mine when it was really cold outside and adjusted them all but they ticked when the engine finnaly got to temp but double tap everything hopefully its sumthin stupid n easy
Forum: Drag Racing
05-03-2009, 04:53 PM
Replies: 28
Views: 5,408
Posted By evo_s_uck

Re: Brad Personett 5.95 @ 250.88

thats insane fwd runnin under 6 sec inna 1/4 mile
Forum: Drag Racing
05-03-2009, 04:48 PM
01-19-2009, 06:58 AM
01-18-2009, 05:08 AM
Replies: 18
Views: 1,007
Posted By evo_s_uck

Re: LS long block GSR tranny Stock B16 head

you still got that b16 head...
Showing results 1 to 16 of 16


 
Forum Jump


All times are GMT -8. The time now is 01:13 PM.