Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: civic_r87111
Showing results 1 to 25 of 500
Search took 0.49 seconds.
Forum: All Motor / Naturally Aspirated
04-12-2010, 01:33 AM
Replies: 11
Views: 3,731
Posted By civic_r87111

Re: Fresh b18c1 build no oil pressure help

I never got more than 6psi on a gauge while cranking the engine with the starter or more than 20psi cold at idle. After spinning a bearing u must clean all oil passage ways and pickup like...
Forum: All Motor / Naturally Aspirated
04-12-2010, 01:27 AM
Replies: 6
Views: 665
Posted By civic_r87111

Re: Whats rods to buy?? and crank help??

Cheapest way out is get the crank reground (the machine shop will tell u how much and if it can be done to spec) and buy some ITR rods off ebay. If all else fails just use GSR rods 95% same thing if...
Forum: All Motor / Naturally Aspirated
04-12-2010, 01:16 AM
Replies: 34
Views: 2,676
Posted By civic_r87111

Re: what happened to these bearings?

LOL, some of u guys.. The coating that is on the journals is a nickle coating and the cranks can be reground to a max of .030" oversized bearing with no issues to spinning/spunning or much integrity...
Forum: Honda Civic / Del Sol (1992 - 2000)
04-01-2010, 09:58 AM
Replies: 14
Views: 1,668
Posted By civic_r87111

Re: Oil Light/Pressure

Normal oil pressure is anywhere from 3-10psi at idle
Forum: Honda Civic / Del Sol (1992 - 2000)
03-24-2010, 10:35 PM
Replies: 14
Views: 1,668
Posted By civic_r87111

Re: Oil Light/Pressure

I don't remember it having it built in so I will have to look at the one I have at the shop tomarrow, u maybe right but not from what I remember.
Forum: All Motor / Naturally Aspirated
03-24-2010, 04:08 PM
Replies: 34
Views: 2,676
Posted By civic_r87111

Re: what happened to these bearings?

I would at least take it to the machine shop and let them check it as well, may just need to be polished back up. If u run ur finger over then journals and feel any indents then it maybe scrap. U...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-24-2010, 09:32 AM
Replies: 14
Views: 1,668
Posted By civic_r87111

Re: Oil Light/Pressure

IDk who told u to take that out but even the Vtec SOHC's have it installed in there, I would put it back in and bet ur problem goes away. Do u have one to use from a SOHC Vtec engine? I haven't...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 10:48 PM
Replies: 14
Views: 1,668
Posted By civic_r87111

Re: Oil Light/Pressure

There is alil oil restricktor in the back side of the block under the head, if that is missing it would cause a big internal oil leak. That's all I can think of that ur cousin is talking about.
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 10:44 PM
Replies: 4
Views: 499
Posted By civic_r87111

Re: need help

That sukx but might as well get a chipped one now.
Forum: Forced Induction
03-23-2010, 10:40 PM
Replies: 25
Views: 22,520
Posted By civic_r87111

Re: Oil Pressure: Mobil1 15w50 vs. Valvoline VR1 20w50

You want a simple answer, ^ just gave u one. If u have stock bearing clearances then stay close to stock recommened viscosity like he said. I have used 5w30 10w30 10w40 and 15w40 and the pressure...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 10:34 PM
Replies: 5
Views: 443
Posted By civic_r87111

Re: Radiator problems

I would say that the head gasket is shot and/or the head is warpped.
Forum: Forced Induction
03-23-2010, 12:29 PM
Replies: 25
Views: 22,520
Posted By civic_r87111

Re: Oil Pressure: Mobil1 15w50 vs. Valvoline VR1 20w50

WOW, y would u judge the oiling capibilities based on pressure? I mean low oil pressure is bad of course and no pressure is worse but just because ur pressure is higher doesn't mean it's lubing or...
Forum: All Motor / Naturally Aspirated
03-23-2010, 12:02 PM
Replies: 34
Views: 2,676
Posted By civic_r87111

Re: what happened to these bearings?

Well since the rod bolts where just hand tight, I would say the the clearance was to big and the oil pushed out of the journals to fast and easy (internal oil leak) so it just didn't get proper...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 11:47 AM
Replies: 3
Views: 681
Posted By civic_r87111

Re: Electric driver window not rolling up properly - 93 Civic LX

Yes, I would say the regulator as well but I would try to adjust the regulator track first b4 buying a new one.
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 11:43 AM
Replies: 4
Views: 499
Posted By civic_r87111

Re: need help

Sounds like ur ecu took a dump or has a bad ground. Check the grounds in the engine bay, the main 2 are the thermostat housing ground and the ground strap from the tranny to the chassis. Make sure...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 11:35 AM
Replies: 14
Views: 1,668
Posted By civic_r87111

Re: Oil Light/Pressure

I can't think of any valve in the oiling system that works like that, there is a pressure relief valve in the pump. It only opens when the pressure is 80+ psi tho. This is an odd situation, same...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 12:20 AM
Replies: 6
Views: 651
Posted By civic_r87111

Re: b20 vtec build and question

I would use the CTR intake cam and the ITR/CTR exhaust cam, those would make good power with out an absolute need to tune, however I highly recommend it with 11.8:1 CR and I would recommened a valve...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 12:12 AM
Replies: 4
Views: 417
Posted By civic_r87111

Re: Help car isn't staying on!!!!!!!

The car was running fine b4 u changed the water pump and belt? If so sounds like it wasn't timed back correctly or something didn't get plugged back in. Need more info to give u better ideas tho.
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 12:08 AM
Replies: 2
Views: 4,579
Posted By civic_r87111

Re: B16a2 Fuel Pressure Regulator??????

What ^ said and u need to have an aftermarket FPR (fuel pressure regulator) or the B&M FPR mod and a FPG (fuel pressure gauge)
Forum: Honda Civic / Del Sol (1992 - 2000)
03-23-2010, 12:05 AM
Replies: 1
Views: 375
Posted By civic_r87111

Re: Ls vtec part numbers?

U can buy a keyway at the hardware store and cut it to length and if u have a honda dealer near u then u can just go to the parts department and ask for the injector seals. I don't know the part #...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-22-2010, 11:55 PM
Replies: 5
Views: 443
Posted By civic_r87111

Re: Radiator problems

Well u have 3 things it could b, leaking, burning, or boiling it out. With the limited info u gave its hard to say. I would properly fill it first and then drive it around for 30 to 45 min's and...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-22-2010, 11:48 PM
Replies: 14
Views: 1,668
Posted By civic_r87111

Re: Oil Light/Pressure

The OPG wouldn't mess it up unless u have a hole in the line and it is slowly pissing out oil but u should notice that (I would think). Haven't seen any fluid trails in the street, driveway, or in...
Forum: Honda Civic / Del Sol (1992 - 2000)
03-22-2010, 11:37 PM
Replies: 22
Views: 5,415
Posted By civic_r87111

Re: Snapped valve cover stud

Yes, same thing
Forum: All Motor / Naturally Aspirated
03-14-2010, 01:19 AM
Replies: 24
Views: 9,014
Posted By civic_r87111

Re: anyone here port their own intake manifold?

I have done it without cutting the manifold open, they make a porting tool to get up inside the runners.
Forum: All Motor / Naturally Aspirated
03-14-2010, 01:14 AM
Replies: 8
Views: 3,036
Posted By civic_r87111

Re: list your ls/vtec set up

Under construction but..
B18A block
B18B crank
B18B rods
PCT (B16B) pistons .25 over
Clevite main bearings
Clevite H series rod bearing
B16A2 head port&polished
Stock valves
PCT springs and...
Showing results 1 to 25 of 500
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 05:51 PM.