Notices
 
Search: Posts Made By: IhateworkingoncaRs
Showing results 1 to 25 of 277
Search took 0.52 seconds.
01-12-2012, 07:34 PM
Replies: 16
Views: 7,375
Posted By IhateworkingoncaRs

Re: B18 EK - 75 psi fuel pressure

After changing all those parts, you are really left with just the fuel pump. The coil in the pump is shorted drawing too much current.
01-12-2012, 02:29 PM
Replies: 42
Views: 2,967
Posted By IhateworkingoncaRs

Re: ls/vtec project help!

It's best to set your TDC when your ready to do the belt, you'll see that it's tricky to fit the belt onto the gear so you'll have to rotate the gear forward or backwards a little. This is where...
01-12-2012, 02:12 PM
Replies: 42
Views: 2,967
Posted By IhateworkingoncaRs

Re: ls/vtec project help!

Don't use the D16z6 cam timing, it's not the same as the b series.
01-12-2012, 02:10 PM
Replies: 42
Views: 2,967
Posted By IhateworkingoncaRs

Re: ls/vtec project help!

TDC simply means that the piston is at the highest point of travel. When TDC is used for setting timing belt, it refers to the piston in cylinder 1 at highest point of travel. With no head on the...
01-12-2012, 01:58 PM
Replies: 42
Views: 2,967
Posted By IhateworkingoncaRs

Re: ls/vtec project help!

To set TDC for your block, put a long screwdriver done the spark plug hole of cylinder 1. Turn the crank till you visually see the screwdriver at TDC. Because the piston hits TDC twice in one...
01-12-2012, 01:42 PM
Replies: 9
Views: 5,738
Posted By IhateworkingoncaRs

Re: thud sound from passanger rear tire

Most likely your rotor as Hidenplanvew said or wheel bearing since the thud acts with rotation and it's not your tires.
03-30-2011, 09:06 AM
Replies: 30
Views: 51,169
Posted By IhateworkingoncaRs

Re: Best Intake Manifold for All Motor B16/GSR setup?

It depends on how much work your going to do. Too small can restrict air flow but too big slows down air velocity.

I'd recommend skunk2.
03-30-2011, 09:03 AM
Replies: 15
Views: 736
Posted By IhateworkingoncaRs

Re: Need help with struts. Pics

Make sure your spring is tighten all the way down and the fork is all the way up. Next, you'll have to pry down your LCA. If it's not the proper fit, your civic is going to look like it has a lift...
03-30-2011, 08:57 AM
Replies: 6
Views: 1,020
Posted By IhateworkingoncaRs

Re: em1 battery quesiton

Check the tension of your belt, it could be slipping at high rpms causing the alternator to not charge. Battery light monitors running voltage, not battery voltage. When it comes on, usually points...
03-30-2011, 08:50 AM
Replies: 15
Views: 736
Posted By IhateworkingoncaRs

Re: Need help with struts. Pics

The spring compressor will only help get the spring on the strut, it won't do anything else.
03-29-2011, 03:23 PM
Replies: 27
Views: 2,675
Posted By IhateworkingoncaRs

Re: Confused on camber

Wow, what a heated thread. Here's my insight, and if anyone cares I do have credentials in suspension, I have an 2 year Automotive Technology degree (associates) and was at one time ASE certified in...
03-29-2011, 02:36 PM
Replies: 8
Views: 3,787
Posted By IhateworkingoncaRs

Re: civic poor gas mileage ?

Might be your regulator and or return lines. The fuel could be in the form of vapor.
03-21-2011, 08:01 AM
Replies: 16
Views: 17,520
Posted By IhateworkingoncaRs

Re: Civic clicks when trying to start,whats wrong?

From the sound of it, that's a bad starter.
03-18-2011, 09:32 AM
Replies: 10
Views: 3,899
Posted By IhateworkingoncaRs

Re: Crank Pulley Bolt!

I'm having a similar problem. I've tried to put the car in gear and lock the brakes to try and stop the pulley from spinning as I don't have what hannslepo is using but the pulley is still spinning....
03-18-2011, 09:24 AM
Replies: 7
Views: 1,947
Posted By IhateworkingoncaRs

Re: 93 civic engine swap

It will be fine, just perform the swap as if it was the same motor.
02-18-2011, 11:37 AM
Replies: 18
Views: 3,688
Posted By IhateworkingoncaRs

Re: 94 accord issues

Unfortunately obd1's don't do a good job of telling us when there maybe a problem with a sensor until it's completely out so it's a long shot to assume that the TPS is bad. It may not even be sensor...
07-30-2010, 10:30 AM
Replies: 6
Views: 594
Posted By IhateworkingoncaRs

Re: Trade:00 Si rolling shell

Just offer, I'll consider anything, I don't have the money to do anything so it's just sitting in my dad's garage which he doesn't like to much.
07-27-2010, 10:17 AM
Replies: 6
Views: 594
Posted By IhateworkingoncaRs

Trade:00 Si rolling shell

My Si was stolen last spring and stripped out. The brakes and suspension was left on it along with some spare tires (LOL), the body was left undamaged (atleast whats left of it). Here are some...
Forum: Want to Buy
10-06-2009, 06:47 PM
Forum: Want to Buy
10-05-2009, 11:32 AM
Forum: Want to Buy
10-03-2009, 07:16 PM
Forum: Want to Buy
10-02-2009, 07:17 PM
Forum: Want to Buy
10-02-2009, 08:33 AM
09-27-2009, 01:51 PM
Replies: 6
Views: 4,260
Posted By IhateworkingoncaRs

Re: CRV wont start 100% when it rains

I love cars, just hate working on them LOL, good luck.
09-27-2009, 11:01 AM
Replies: 7
Views: 3,815
Posted By IhateworkingoncaRs

Re: turbo crv?

I don't think it would hold up too well, the axles in the rear are tiny.
Showing results 1 to 25 of 277
 


 
Forum Jump


All times are GMT -8. The time now is 08:35 AM.