Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: "00"R
Showing results 1 to 25 of 64
Search took 0.54 seconds.
Forum: Forced Induction
11-04-2007, 08:06 PM
Replies: 6
Views: 904
Posted By "00"R

Re: Anyone with a stock motor turbo b18c5 (ITR32)

If you intend on keeping the engine completely stock I would suggest a garret gt 2860rs, that should get you to about 300whp safely. If you lower the compression and change the rods I would suggest...
Forum: Forced Induction
11-04-2007, 02:19 PM
Replies: 6
Views: 904
Posted By "00"R

Re: Anyone with a stock motor turbo b18c5 (ITR32)

i have a b18c5 running 7 lbs with a garret gt28rs it makes about 280 whp right now on a hondata. it needs vavle guides and smokes a little bit so i'm not trying to push it any harder. but previosly...
Forum: Forced Induction
10-24-2007, 06:50 PM
Replies: 6
Views: 4,453
Posted By "00"R

Re: Garrett Gt2871r or GT2860rs on B18c1... (brianmcivics)

Yea I would definatley suggest the 2871, I have a 28rs on my setup and I wish I had a 2871, you will sacrifice a little bit of response, but it will make power more eficienly were it counts. Also if...
Forum: Forced Induction
10-22-2007, 04:08 PM
Replies: 11
Views: 1,458
Posted By "00"R

Re: Does anyone here have used or tried a Carbonetics twin disc carbon clutch? (V-SPEC 1)

I have one on my setup. granted its way over kill, I love it. Aside from the rattle it makes when you have the pedal pushed in, it works great. When i first put it in it chattered real bad but...
Forum: Forced Induction
10-18-2007, 09:31 AM
Replies: 22
Views: 3,449
Posted By "00"R

Re: (Blind-Fashion)

the 28rs is a gt2860 not a 2871rs. go with the 2871, the 28rs won't be enough for your goals. I'm in the same boat, I have a gt28rs and I wish I had a gt2871 or a gt30r.
Forum: Forced Induction
10-18-2007, 09:03 AM
Replies: 32
Views: 11,043
Posted By "00"R

Re: Help with high torque b16 b18c build with gt28rs turbo (bootlegcivic)

that manifold is not a bad manifold at all, it spools well and made great power on my setup, but if you look at a good log mani or even a ram horn, the desighn is so that it places the turbo in a...
Forum: Forced Induction
10-16-2007, 09:39 AM
Replies: 32
Views: 11,043
Posted By "00"R

Re: Help with high torque b16 b18c build with gt28rs turbo (airmaxbri)

it's a great theory that you have about building a fun to drive high torque engine. I have a few suggestions for you though. I'll start with sleeveing, another great thoery, the problem is that you...
Forum: Acura Integra Type-R
08-21-2007, 02:44 PM
Replies: 471
Views: 168,621
Posted By "00"R

Re: Re: (get RIGHT)

yea the car was PY to start, but it had been painted a few times from a few accidents before I baught it, so there were a few diffrent shades of yellow on.
Forum: Acura Integra Type-R
08-20-2007, 07:23 PM
Replies: 471
Views: 168,621
Posted By "00"R

Re: Re: (vtecjerry)

well that wasn't what I was looking to hear LOL, but thats cool. I guess I'm gonna go back to yellow when I re-do it, maybe a little carbon fiber. Thanks for the input I guess.
Forum: Acura Integra Type-R
08-19-2007, 04:01 PM
Replies: 471
Views: 168,621
Posted By "00"R

Re:

Heres mine
https://i215.photobucket.com/albums/cc202/eaw00R/S5000632.jpg
https://i215.photobucket.com/albums/cc202/eaw00R/S5000631.jpg
Forum: Acura Integra Type-R
08-19-2007, 10:39 AM
Replies: 11
Views: 1,351
Posted By "00"R

Re: (Doostur)

i'll do it if you wanna drive to colorado.
lol
Forum: Acura Integra Type-R
08-09-2007, 06:29 PM
Replies: 310
Views: 24,781
Posted By "00"R

Re:

WTB: I am looking for the carbon fiber ashtray and cig. lighter panel.
Forum: Welding / Fabrication
08-07-2007, 11:42 AM
Replies: 60
Views: 3,427
Posted By "00"R

Re: (CBURKE)

yea you do that with any kind of welding pretty much
Forum: Welding / Fabrication
08-07-2007, 07:33 AM
Replies: 60
Views: 3,427
Posted By "00"R

Re: (CBURKE)

from all the pictures ive seen it looks like you arent leaving any gap between the pipes. leave a gap about the thickness of your material or maybe a little less. this will help the weld penetrate...
Forum: Paint and Body
07-31-2007, 12:04 AM
Replies: 2
Views: 995
Posted By "00"R

Re: Painting car.. problem while painting roof (JdmFrontDc)

that would have more to do with your reducer rather than your hardner. its hard to recomend a solution for you because there are so many variables. you could be haveing this problem because your...
Forum: Paint and Body
07-23-2007, 04:22 PM
Replies: 16
Views: 10,270
Posted By "00"R

Re: remove factory spot welds. drill or spot weld bit? (dinko)

I use a 5/16" dewalt self centering bit from home depot. Its kinda half way like a spot weld bit. They cost about $7-$8. The nice thing is that if your carefull they only leave about an 1/8" hole...
Forum: Paint and Body
07-23-2007, 04:16 PM
Replies: 13
Views: 41,642
Posted By "00"R

Re: How to pull fenders?? not roll, pull.. (nfinitecc)

I dont get it, what are you trying to pull. Is there a dent to pull or are you trying to pull the fender off the car, what do you mean?
Forum: Paint and Body
07-23-2007, 04:09 PM
Replies: 7
Views: 1,061
Posted By "00"R

Re: (IP RACING)

with omni you can pretty much use any urethane reducer, but make sure its made for urethane. And also make sure its not a reactive reducer.
Forum: Paint and Body
07-23-2007, 04:05 PM
Replies: 25
Views: 8,601
Posted By "00"R

Re: (talkJDM)

The reason why most shops tell the customer to wait to wash it is to cover there ass. The fact of the matter is whether you bake it or not the clear is still breathing and cureing for about 20-30...
Forum: Paint and Body
07-23-2007, 03:45 PM
Replies: 5
Views: 758
Posted By "00"R

Re: bondo question (milkmanLCA)

another option is a flexible polyester glaze. you use it pretty much just like any other filler. But its a good idea to put some adhesion promoter on before you put on the filler. I've had great...
Forum: Classifieds: Forced Induction
07-19-2007, 12:42 PM
Replies: 0
Views: 311
Posted By "00"R

FS: love fab manifold

it is a b-series love fab mini-me eq manifold t3/38mm and I also have a dump tube to go with it. I paid 700 just for the manifold, will take $500 shipped with the dump tube.
here is the adress of...
Forum: Paint and Body
07-18-2007, 12:45 PM
Replies: 1
Views: 373
Posted By "00"R

Re: help: featheredging on the round surface of the fender (cilvia)

there really is no "trick" to it, but there are many techniques you could try. In your case I like to use some type of block with a bit of flex to it and always try to sand accros two diffrent...
Forum: Forced Induction
06-21-2007, 07:58 AM
Replies: 4
Views: 621
Posted By "00"R

Re: (BrockNB)

yes an oil restrictor but no catch can
Forum: Forced Induction
06-20-2007, 10:06 AM
Replies: 4
Views: 621
Posted By "00"R

lovefab mani.

I am having a hell of a time trying to figure out why my car blows oil smoke. It's coming from the turbo but why. The drain line is as perfect as it's gonna get and there is no crankcase preasure,...
Forum: Paint and Body
06-19-2007, 04:16 PM
Replies: 4
Views: 1,818
Posted By "00"R

Re: Air dry vs. Force dry ("00"R)

thats pretty much how I feel, but I'm in the middle of trying to decide what product to use at my shop, we have been using sherwin williams and have been having complaints about how soft it stays. ...
Showing results 1 to 25 of 64
 
Page 1 of 3
1
2
3


 
Forum Jump


All times are GMT -8. The time now is 04:04 PM.