Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 2
1
2
Search: Posts Made By: clutchrsx
Showing results 1 to 25 of 27
Search took 0.70 seconds.
Forum: Tech / Misc
06-13-2010, 07:36 PM
Replies: 20
Views: 1,668
Posted By clutchrsx

Re: $50 to the person that fixes this

with the car running, ensure that the alternator is charging the battery. should be 14v+ while running, if not your battery wont have enough juice to start it up again
Forum: Tech / Misc
04-02-2010, 10:47 PM
Replies: 2
Views: 883
Posted By clutchrsx

Re: rings and bearing help

http://www.wiseco.com/PDFs/Manuals/RingEndGap.pdf

oem bearings are fine.

do u happen to know your piston to wall clearance?
Forum: Tech / Misc
04-02-2010, 10:40 PM
Replies: 4
Views: 622
Posted By clutchrsx

Re: Oil orifce pins install on bseries vtec heads

take out the allen plug on the side of the head to gain access to the shafts that hold the rockers in place. a 17mm honda bolt will thread into the shaft. pull the shaft out a little and u'll see the...
Forum: Tech / Misc
04-02-2010, 05:15 PM
Replies: 8
Views: 541
Posted By clutchrsx

Re: Cooling Problem

when your temperature gauge goes down, do u still have HOT heat?

bleed the cooling system properly after changing tstat?
Forum: Tech / Misc
04-02-2010, 05:11 PM
Replies: 4
Views: 1,168
Posted By clutchrsx

Re: single cam crank specs.

if u replace your crank with another, be sure u measure bearing clearances for mains and rods
Forum: Tech / Misc
04-02-2010, 05:07 PM
Replies: 4
Views: 622
Posted By clutchrsx

Re: Oil orifce pins install on bseries vtec heads

the taller pin goes on the exhaust side and the flat/shorter pin goes on intake. if u have it reversed, cam caps wont close
Forum: Tech / Misc
03-30-2010, 09:03 AM
Replies: 6
Views: 642
Posted By clutchrsx

Re: BUILT MOTOR NOT SEALING PROPERLY

its recommended to be using the copper headgaskets with oring'ed blocks. what are u torquing the head down to? reputable shop do the oringing? it's either your orings or the headgasket not sealing...
Forum: Tech / Misc
03-14-2010, 01:15 AM
Replies: 4
Views: 1,868
Posted By clutchrsx

Re: how much rod stretch ?? eagle rods in B18B

whops. yea meant tenthou.. duh me! must be an idiot to do .062 lol
Forum: Tech / Misc
03-11-2010, 02:40 AM
Replies: 4
Views: 1,868
Posted By clutchrsx

Re: how much rod stretch ?? eagle rods in B18B

i normally stretch them out to about 58 -62thou
Forum: Tech / Misc
02-18-2010, 12:13 PM
Replies: 12
Views: 6,290
Posted By clutchrsx

Re: b18a1 rod bearings clearances issue...

what kind of bearings are u using?
Forum: Tech / Misc
02-13-2010, 12:36 AM
Replies: 6
Views: 2,879
Posted By clutchrsx

Re: How do manufacturers determine the appropriate Oil Viscosity?

The main reason 5W-20 was specified for your engine is to increase the CAFE (Corporate Average Fuel Economy) reported to the Federal Government. CAFE is the combined average fuel economy of all of a...
Forum: Tech / Misc
02-12-2010, 04:15 PM
Replies: 1
Views: 597
Posted By clutchrsx

Re: K24a2 Engine?

yes it will.
Forum: Tech / Misc
12-30-2009, 12:03 PM
Replies: 4
Views: 918
Posted By clutchrsx

Re: clearances on a d16y8 Crower stg2 turbo cam, SI 1mm over valves

i can't tell you if it clears or not since i've never had that particular set up. but i'd clay it anyways.. doesn't take much time. i highly doubt you'll have clearance issues.

your problem with...
Forum: Tech / Misc
12-30-2009, 11:50 AM
Replies: 10
Views: 27,436
Posted By clutchrsx

Re: cutting axle nut

spray some pb blaster and let it soak a little. put the socket on a STURDY 1/2" ratchet. i use the handle of my jack as a breaker bar. have someone hold the brakes to keep it from spinning. pop it...
Forum: Tech / Misc
12-27-2009, 01:22 AM
Replies: 4
Views: 918
Posted By clutchrsx

Re: clearances on a d16y8 Crower stg2 turbo cam, SI 1mm over valves

first off.. do you know how to clay the motor while locking it in vtec?
what compression pistons? i highly doubt you'll have clearance issues with low compression pistons unless the cams are that...
Forum: Tech / Misc
12-27-2009, 01:12 AM
Replies: 6
Views: 950
Posted By clutchrsx

Re: b18 b1 swap help

M10-1.25 is what your looking for

or just grab a nut off your strut bolt, its a 14mm nut and go size it at lowes. and find a bolt that threads through the nut..
Forum: Hybrid / Engine Swaps
12-26-2009, 10:06 PM
Replies: 4
Views: 965
Posted By clutchrsx

Re: LS/VTEC into 94 civic DX questions...

u can use any obd1 harness basically, civic or integra.. then u have to add wires from the shock tower plugs to the ecu. and depending on if u got a vtec harness or not u would have to run wires from...
Forum: Tech / Misc
12-26-2009, 09:57 PM
Replies: 1
Views: 1,656
Posted By clutchrsx

Re: Distributor question... Vtec to non-Vtec?

it will work but i believe only 2 of the 3 legs will bolt up
Forum: Tech / Misc
12-26-2009, 09:53 PM
Replies: 18
Views: 14,161
Posted By clutchrsx

Re: Misfire/Bog at Full Throttle

any cel's at all?

did u switch plugs on the iacv and the iat?
Forum: Tech / Misc
12-26-2009, 09:48 PM
Replies: 4
Views: 449
Posted By clutchrsx

Re: NEED HELP!!!!

B-SERIES
A = gnd Green/White
B = map signal White
C = 5v Yellow/Red

For verification check inside the Honda Map sensor plug. The pins may be labeled...
Forum: Tech / Misc
12-26-2009, 03:17 PM
Replies: 20
Views: 128,745
Posted By clutchrsx

Re: pr3-3 & pr3-2 head stamp. what are the differences? specs?

yep, its a 2000 B16 head. and yep b18b= LS
Forum: Tech / Misc
12-26-2009, 03:14 PM
Replies: 5
Views: 673
Posted By clutchrsx

Re: Which radiator??

yes that. i had a mishimoto and it cracked near the bottom = leakkkkkkkk
Forum: All Motor / Naturally Aspirated
12-26-2009, 12:51 AM
Replies: 12
Views: 1,295
Posted By clutchrsx

Re: gsr dies out

take off the vtec solenoid and check the screen/filter to see if its clogged or dirty. make sure oil level is good
Forum: Tech / Misc
12-26-2009, 12:48 AM
Replies: 2
Views: 2,000
Posted By clutchrsx

Re: Rebuilt engine break-in??

for break in, i usually take it out a good 50 miles or so with A LOT of engine braking which helps with seating the new rings. and if you're on a proper map, get on it all u want!

been good for...
Forum: Tech / Misc
12-26-2009, 12:43 AM
Replies: 5
Views: 673
Posted By clutchrsx

Re: Which radiator??

a stock civic replacement will work fine, or you can get an aftermarket civic radiator.
Showing results 1 to 25 of 27
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -8. The time now is 01:47 AM.