Notices
 
Search: Posts Made By: QuarterMileMaster
Showing results 1 to 25 of 496
Search took 2.30 seconds.
Forum: Acura TSX
01-08-2015, 03:47 PM
Replies: 2
Views: 771
Posted By QuarterMileMaster

Re: HELP!!! Connector Identification

2004
Aaaaaahhhhh, that's exactly what it is. I forgot to bolt that damn thing up which is why I couldn't figure out where the plug went. Thanks!!!

I don't suppose you know of a quick link to a...
Forum: Acura TSX
01-08-2015, 03:14 PM
Replies: 2
Views: 771
Posted By QuarterMileMaster

HELP!!! Connector Identification

Ok, so I'm retarded and forgot to label two connectors that go on the side of the cylinder head. They are both 2 pin connectors. One has to be the coolant temp sensor on the side of the cylinder...
Forum: For Sale
02-28-2013, 03:25 PM
Forum: For Sale
02-18-2013, 08:53 AM
Replies: 9
Views: 1,574
Posted By QuarterMileMaster

Forum: For Sale
01-28-2013, 02:36 PM
Replies: 9
Views: 1,574
Posted By QuarterMileMaster

12-26-2012, 12:10 PM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

Ok, so the whole ballgame changed. All along, I've been noticing that wire colors weren't the same as what you've been describing and by alldata but I just assumed that the pin numbers were the...
12-24-2012, 09:30 AM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

What I meant with the continuity was that with the 28pin plug connected to the module, all wires were testing pos continuity with each other. Went ahead and replaced the eps control module and its...
Forum: For Sale
12-18-2012, 02:02 PM
12-17-2012, 11:28 AM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

Ok, so I think the EPS control unit is bad. With the 28pin connector plugged into the control unit, I get positive continuity between all 3 torque sensor wires at both connections at the firewall...
12-14-2012, 09:13 AM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

So here's my next question then, could we pick up a good condition used rack and just swap the sensor?

Also, he said the code that came up is "22-01: Engine speed signal", what does that have to...
12-13-2012, 12:30 PM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

So I took it to our local honda dealer and he said that the torque sensor is bad according to their HDS. However, he told me on the '09 si's that the sensor isn't servicable, you have to replace the...
12-12-2012, 12:14 PM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

Is it possible that I need to do this procedure? (copy and pasted from alldata)

Memorizing The Torque Sensor Neutral Position

The torque sensor neutral position must be memorized whenever the...
12-11-2012, 06:18 AM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

How do I test the torque sensor? I would just think that I'd be getting an eps light, but I'm not, which I don't understand.

Clarification: Everything installed, car on the ground, the key is...
12-06-2012, 01:58 PM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

Ok, so I got the new abs sensors and axles installed. ABS light went away of course but the steering is still doing the exact same damn thing.

Kingteg, please send me any info you can, sensor...
Forum: For Sale
12-06-2012, 01:54 PM
Forum: For Sale
12-04-2012, 03:19 PM
Forum: For Sale
12-01-2012, 10:40 AM
Forum: For Sale
11-30-2012, 07:31 PM
Replies: 9
Views: 1,574
Posted By QuarterMileMaster

Re: FS: COMPLETE K20z1 head w/z3 Cams

Need it gone, $550 obo
Forum: For Sale
11-29-2012, 04:31 PM
11-29-2012, 06:44 AM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

Re: 09 Si: EPS Malfunction???

No EPS light that I can tell. I hooked our Modis up to the car and the only code I can find is a U0122, which from what I've read is related to the Hondata flashpro. All connectors seem fine. ABS...
Forum: For Sale
11-28-2012, 08:48 PM
Replies: 9
Views: 1,574
Posted By QuarterMileMaster

FS: COMPLETE K20z1 head w/z3 Cams

This is a complete K20z1 head out of a 2006 RSX Type-S with 63,XXX miles. It has K20z3 cams in it, everything else is stock and in great condition. Valve seals are still good and the head has been...
11-28-2012, 11:28 AM
Replies: 22
Views: 19,434
Posted By QuarterMileMaster

09 Si: EPS Malfunction???

I've got an 09 Civic Si coupe here at my shop that had a turbo kit installed, customer blew the motor (turned boost above tuned limit) so upon initial inspection I dropped the subframe down enough to...
11-01-2012, 10:57 AM
Replies: 1
Views: 896
Posted By QuarterMileMaster

Making changes in Crome causing limp mode! HELP!!!

Here's the setup:
B18a w/P30 Pistons
BC Stg 2 Cams
Blox IM
Yonaka Header
Prelude Injectors

So, I can upload the basemap from Crome that's labeled B18b p30 and the car will start and run...
08-29-2012, 07:30 AM
Replies: 4
Views: 754
Posted By QuarterMileMaster

Re: FML: No spark or fuel: 93 Si Hatch, OBD2 B18c

That's exactly what I did lol, thanks.
08-28-2012, 12:53 PM
Replies: 4
Views: 754
Posted By QuarterMileMaster

Re: FML: No spark or fuel: 93 Si Hatch, OBD2 B18c

After spending all day on this he decided to finally tell me the car was stolen at one point and the steering column got busted. It's the stupid ignition switch.
Showing results 1 to 25 of 496
 


 
Forum Jump


All times are GMT -8. The time now is 03:07 AM.