Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 9
1
2
3
Last »
Search: Posts Made By: SlammedAccord96
Showing results 1 to 25 of 213
Search took 0.98 seconds.
Forum: Honda Accord (1990 - 2002)
09-07-2008, 06:57 PM
Replies: 4
Views: 15,823
Posted By SlammedAccord96

Re: 1997 Honda Accord Wheel bearing (rcgrillo)

Ok, I'll just give u a step by step on how to replace these. First, there are two parts to a hub assembly, the hub (part with the axle spines and the wheel studs), and the bearing. On the accord...
Forum: Honda Accord (1990 - 2002)
06-14-2008, 08:16 PM
Replies: 0
Views: 636
Posted By SlammedAccord96

CEL Code 0, No start - Confused!!

Ok, I have a 91 Accord LX Sedan 5-speed, with a JDM H22A. I am running a JDM P13 OBD1 ECU. About a week ago, I drove the car for an hour on the highway, parked it for 2 hours, and got back in. Car...
Forum: Honda Accord (1990 - 2002)
06-10-2008, 07:44 PM
Replies: 7
Views: 4,283
Posted By SlammedAccord96

Re: how to get press in rotors off 97 accord easily??????????? (DCFIVER)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by DCFIVER &raquo;</TD></TR><TR><TD CLASS="quote">^^^^ Thats hard. Use a slide hammer...
Forum: Honda Accord (1990 - 2002)
06-10-2008, 03:27 AM
Replies: 7
Views: 4,283
Posted By SlammedAccord96

Re: how to get press in rotors off 97 accord easily??????????? (vtecmissle)

what didn't come off? Take off the axle nut (36mm), unbolt the caliper from the knuckle, then unbolt the upper and lower balljoints, tie rod end, and remove the knuckle from the car. Then you will...
Forum: Honda Accord (1990 - 2002)
05-23-2008, 05:44 PM
Replies: 7
Views: 8,199
Posted By SlammedAccord96

Re: 90 Accord low idle/speedometer problems (quizbo99)

unplug the IACV and set the idle with the white screw on the TB to 550RPM in neutral, warmed up, with no accessories. Then plug in the IACV and it should raise to 750RPM.

For the speedometer,...
Forum: Honda Accord (1990 - 2002)
05-17-2008, 07:49 PM
Replies: 5
Views: 2,469
Posted By SlammedAccord96

Re: need help!!!! h22 swap limp mode (Kurumi)

The easy way to solve the problem, if he was "cleaning up wiring", would be to buy another stock F22 accord engine harness (junkyard/ebay/etc) and modify it to work with the H22 again. Unless you...
Forum: Honda Accord (1990 - 2002)
05-17-2008, 07:44 PM
Replies: 14
Views: 23,335
Posted By SlammedAccord96

Re: (j_kevin_ca)

at work we measure new rotors for run out ("warpage") before installing them, sometimes, especially with the cheaper brands, they have excessive amounts of run out right out of the box...so we have...
Forum: Honda Accord (1990 - 2002)
05-04-2008, 06:03 PM
Replies: 4
Views: 498
Posted By SlammedAccord96

Re: (TheMuffinMan)

i got mine, complete engine (no trans/ecu) for $900 shipped from tiger japanese, it runs great! I couldn't be happier with them!
Forum: Honda Accord & Crosstour (2003 - 2012)
05-01-2008, 04:36 AM
Replies: 10
Views: 956
Posted By SlammedAccord96

Re: Friends 05 Accord pulling. (JimBlake)

yup I was just going to say this - i do alignments at work and bad tires are a large percentage of pulls on alignments that come back - rotate them and see what happens.
Forum: Honda Accord (1990 - 2002)
04-29-2008, 04:28 AM
Replies: 2
Views: 548
Posted By SlammedAccord96

Re: Trying to take out radio...Having difficulties... (tRaCeYoUiNcHaLk)

You have to grab right under the knob (on the boot) and squeeze, and pull down, and it will separate the boot from the knob. Then spin the knob counterclockwise and it will come off. Then slip the...
Forum: Honda Accord (1990 - 2002)
04-28-2008, 05:18 PM
Replies: 3
Views: 3,942
Posted By SlammedAccord96

Re: stupid question but: are my rotors supposed to be boiling hot when im done driving? (RS-2)

Is the caliper sticking? Are both wheels doing the same thing? Rotors do get really hot and if you were riding the brakes then it would be even worse. This may indicate a problem in your braking...
Forum: Honda Accord (1990 - 2002)
04-28-2008, 05:17 PM
Replies: 7
Views: 778
Posted By SlammedAccord96

Re: (bopbop93030)

stupid question, but did you check tire pressure?
Forum: Honda Accord (1990 - 2002)
04-28-2008, 05:12 PM
Replies: 15
Views: 11,658
Posted By SlammedAccord96

Re: (SlammedAccord96)

Well - I finally passed!

Hydrocarbons

Were:
Idle-196ppm, 2500RPM-211ppm

Now:
Idle - 11ppm, 2500RPM-11ppm
Forum: Honda Accord (1990 - 2002)
04-26-2008, 05:54 PM
Replies: 5
Views: 735
Posted By SlammedAccord96

Re: my accord lights dont work after intalling after market radio (import image)

Hmm, I'd make sure the illumination wire at the radio isn't shorting out, and make sure the fuse is good, usually it will blow. what year accord?
Forum: Honda Accord (1990 - 2002)
04-26-2008, 05:53 PM
Replies: 15
Views: 11,658
Posted By SlammedAccord96

Re: (zombiesid1)

thanks for the replies guys! First, sadly, Delaware's waiver is that I have to spend $750 at an authorized emissions repair facility. So that's not going to happen lol.
...
Forum: Honda Accord (1990 - 2002)
04-25-2008, 02:40 AM
Replies: 15
Views: 11,658
Posted By SlammedAccord96

Re: (3zFree)

I have Neuspeed wires that are like a month old, and I used some b/s autolite plugs because they were out of the v-powers. I did notice that I had my intake air temperature sensor unhooked, so I...
Forum: Honda Accord (1990 - 2002)
04-24-2008, 06:52 PM
Replies: 4
Views: 7,096
Posted By SlammedAccord96

Re: 92 Accord- Dash Board Removal (Toasted576)

The clock just pops out, use a flat head with a towel around it or something, no screws at all!
Forum: Honda Accord (1990 - 2002)
04-24-2008, 07:27 AM
Replies: 15
Views: 11,658
Posted By SlammedAccord96

Re: Need to lower CO emissions drastically!! H22 Accord (Turbowa)

Ok, I'll check the ignition timing, but would those high numbers (7.85% when it should be 1.20%) only be caused by the cat? Is the cat that important? Thanks for the quick responses guys!
Forum: Honda Accord (1990 - 2002)
04-24-2008, 05:32 AM
Replies: 15
Views: 11,658
Posted By SlammedAccord96

Need to lower CO emissions drastically!! H22 Accord

Ok, I have an OBD1 JDM H22A (JDM p13 ECU) in my 91 accord lx 5spd sedan, only mod is an aftermarket header. Had a FULL tuneup 500 miles ago (fuel/air/oil filter, pcv valve,...
Forum: Honda Accord (1990 - 2002)
04-10-2008, 05:19 AM
Replies: 6
Views: 4,505
Posted By SlammedAccord96

Re: (m0nee)

I'd jack up the front of the car, grab the rim and shake it left to right, if you feel play then have a friend do it while you look for the loose part, inner or outer tie rod. If not, then it might...
Forum: Honda Accord (1990 - 2002)
03-23-2008, 07:11 AM
Replies: 2
Views: 658
Posted By SlammedAccord96

Re: Considering a purchase of a CRX or Civic for an extra get around car (w3developing)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by w3developing &raquo;</TD></TR><TR><TD CLASS="quote">Hello,

I am trying my luck here as it seems like...
Forum: Honda Accord (1990 - 2002)
02-20-2008, 06:09 PM
Replies: 1
Views: 3,368
Posted By SlammedAccord96

Re: What would make an inner tie rod fail quickly/prematurely? (Secret Chimp)

What makes you think it went bad, did you jack it up and feel for play in that part? What brand was it (OEM/autozone/etc.)? About the alignment thing, when we do alignments we don't have a reason...
Forum: Honda Accord (1990 - 2002)
01-07-2008, 07:14 PM
Replies: 5
Views: 708
Posted By SlammedAccord96

Re: Maintenance Required Light? (TouringAccord)

99% of the time its just holding the trip button down while the key is off, then (while holding the button) turn it to ignition (engine off tho) and hold it for 10 seconds.
Forum: Honda Accord (1990 - 2002)
01-02-2008, 01:45 PM
Replies: 2
Views: 781
Posted By SlammedAccord96

H22A Swap 90% complete but not starting?

I have a 92-95 JDM H22A engine in my 91 Accord LX Sedan 5speed, with stock F22A manual trans. Anyway, the swap is complete except for the VTEC wiring, secondary intake thing, and knock sensor wiring....
Forum: Honda Accord (1990 - 2002)
12-23-2007, 01:27 PM
Replies: 8
Views: 25,254
Posted By SlammedAccord96

Re: (Jay84ever)

Aren't the pre-90's accords 4x100? Was it on one of them? Are you sure it was on an Accord? If your accord is 4 lug, then it has to be 4x114.3.
Showing results 1 to 25 of 213
 
Page 1 of 9
1
2
3
Last »


 
Forum Jump


All times are GMT -8. The time now is 07:40 AM.