Honda-Tech - Honda Forum Discussion

Notices
Search: Posts Made By: freeeked
Showing results 1 to 22 of 22
Search took 1.00 seconds.
Forum: Honda CRX / EF Civic (1988 - 1991)
10-22-2005, 12:15 PM
Replies: 33
Views: 939
Posted By freeeked

If the tab has really warped the nut then it...

If the tab has really warped the nut then it could be difficult even with a 500lb. If axle is toast you may want to try a dremel or something to cut it off.
Forum: Honda CRX / EF Civic (1988 - 1991)
07-20-2005, 04:58 AM
Replies: 5
Views: 525
Posted By freeeked

Re: Wheel Rub after Camber Kit (Bunger)

It is a fully adjustable camber kit. No I didn't notice this problem before. I am probably go to slap some stock shock/spring assemblies on it and see what the ride height is. I am resigned now...
Forum: Honda CRX / EF Civic (1988 - 1991)
07-18-2005, 08:35 PM
Replies: 5
Views: 525
Posted By freeeked

Wheel Rub after Camber Kit

Here is the situation. I have had 17" wheels on my 91 crx for 3 years. I have suspension techniques lower springs (probably 1.5" drop). No rubbing problems whatsoever. I had a blow-out and...
Forum: Honda CRX / EF Civic (1988 - 1991)
04-29-2005, 08:40 PM
Replies: 3
Views: 560
Posted By freeeked

CRX Dx Auto Intermittent Stall Problem

Driving to work this morning. Clear day (2 C - 35 F). Going about 80kph and the car just died. Engine light came on (oil and battery light to - just like you turned the key off) and the car kept...
Forum: Honda CRX / EF Civic (1988 - 1991)
09-20-2004, 09:57 AM
Replies: 4
Views: 6,418
Posted By freeeked

Rust around windshield (cost to fix)

My windshield cracked and leaking on my 88 crx dx, so I want to replace it. There is some substantial rust bubbbling up at the top of the "pillars" top corners of the winshield. This is my winter...
Forum: Honda CRX / EF Civic (1988 - 1991)
07-10-2004, 12:54 PM
Replies: 4
Views: 1,055
Posted By freeeked

Removal of pedal assembly

I am trying to remove the whole pedal assembly in a 88' CRX si. Can I do it with out removing the steering column? I have gotten 3 bolts off and they were not easy. Any one got any tips. I can't...
Forum: Audio / Security / Video
07-02-2004, 05:29 AM
Replies: 3
Views: 445
Posted By freeeked

Re: Fog Light Wiring (fcm)

Yes the instructions and wiring diagram were vague to say the least. As I understand you tap into the headlight circuit on the control side of the relay. The current from the headlight circuit...
Forum: Audio / Security / Video
06-30-2004, 11:07 PM
Replies: 3
Views: 445
Posted By freeeked

Fog Light Wiring

I am attempting to install a set of fog lights. They came with a wiring kit. However the kit was set to hook the lights into the high or low beams. I wired it up for constant power (using the...
Forum: Honda CRX / EF Civic (1988 - 1991)
06-29-2004, 09:29 PM
Replies: 7
Views: 444
Posted By freeeked

Re: (Andzey)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Andzey &raquo;</TD></TR><TR><TD CLASS="quote">Im looking to find some manual or any .pdf file about how...
Forum: Honda CRX / EF Civic (1988 - 1991)
06-28-2004, 05:05 AM
Replies: 7
Views: 444
Posted By freeeked

Re: (91hob20hb)

Thanks, I have a full set of swap stuff. So the hubs on the dx have a different config than the SI. I have the Si axles and will probably switch the dx to auto. From the sounds of it I will have...
Forum: Honda CRX / EF Civic (1988 - 1991)
06-19-2004, 08:52 PM
Replies: 7
Views: 444
Posted By freeeked

Putting a 91 CRX Si Motor in an 88 CRX DX Auto

I am considering dropping my old 1991 CRX Si Motor into an automatic 1988 CRX dx. I have an 1988 crx engine harness for the D16a1 motor. Also the ECU, linkages, headers from the 91 as well as all...
Forum: Honda CRX / EF Civic (1988 - 1991)
09-07-2003, 09:40 PM
Replies: 5
Views: 437
Posted By freeeked

Re: CRX New B16 Seems to be Running Hot (90blackcrx)

It came out of a wrecked CRX and the guy said he replaced most of the stuff (water pump, clutch etc). It does not blow hot just warm. The fan does come on when it warms up. So the temp guage reads...
Forum: Honda CRX / EF Civic (1988 - 1991)
09-07-2003, 11:46 AM
Replies: 5
Views: 437
Posted By freeeked

CRX New B16 Seems to be Running Hot

Just finished my swap and got to drive around yesterday quite a bit. After a bit the temperature inside the car seemed to be increasing (not much just noticably - and it was a hot day(. I flipped...
Forum: Honda CRX / EF Civic (1988 - 1991)
09-06-2003, 11:06 PM
Replies: 4
Views: 2,561
Posted By freeeked

Re: part # for input shaft bearing in 91 Si tranny. (bc_psychocivic)

I'm am not quite sure the part you are looking for but I use this site to help with the numbers.
http://www.cybrrpartspro.com/M....html...
Forum: For Sale
09-04-2003, 08:38 PM
Replies: 12
Views: 628
Posted By freeeked

Re: JDM CRX EF-8 Vtec Gauge Cluster complete with wire harness and speed sensor for tranny! (naisa01

Do you still have that cluser and speed sensor?

Is it in KPH?

Do you have pics?

I am looking to put it in a 1991 CRX Si with a B16a1. Mine is all messed up!

I will PM you just in case...
Forum: Honda CRX / EF Civic (1988 - 1991)
09-02-2003, 08:55 PM
Replies: 2
Views: 435
Posted By freeeked

B16 Swap Intake Wheeze at Shut Down

I have just finished B16a swap into my CRX. It fires up fine and runs smooth, but when I shut down the a wheezing noise comes from the intake. The only description was a little like Darth Vader...
Forum: Honda CRX / EF Civic (1988 - 1991)
08-28-2003, 08:50 PM
Replies: 5
Views: 721
Posted By freeeked

B16a1 sub-engine harness mismatch HELP

I have dropped a JDM b16 into by 91 CRX si and have just started to hook up the wires and noticed on the drivers side of the engine bay the harnesses do not match. I think the helms calls these the...
Forum: Honda CRX / EF Civic (1988 - 1991)
08-21-2003, 04:24 PM
Replies: 4
Views: 781
Posted By freeeked

B16 Swap Can I leave the Front Mount

I couldn't find the answer in the archives. I understand that when I swap the b16 in using Hasport mounts, I do not need the front mount any longer. Hasport does not mention whether I need to cut...
Forum: Tech / Misc
08-16-2003, 04:19 PM
Replies: 3
Views: 830
Posted By freeeked

Re: Corner Valve Cover Bolt Broke off (JDMDA9)

I was actally trying to loosen it so I could move a grounding cable out of the way of a hoist chain I was attaching. Darn thing!
Forum: Tech / Misc
08-16-2003, 03:24 PM
Replies: 3
Views: 830
Posted By freeeked

Corner Valve Cover Bolt Broke off

I searched previous posts and this sounds like a common occurance. My problem is that I broke this valve cover bolt off:
http://www3.telus.net/~morgand...t.jpg...
Forum: Tech / Misc
08-16-2003, 03:21 PM
Replies: 0
Views: 508
Posted By freeeked

Hoist points for pulling a B16a out of a CRX

Hi,

Here are the two mounting points I had chosen for pulling a B16 out of a crx. One is on the head (just an empty bolt hole on the back of the head)

The second is the bracket the clutch...
Showing results 1 to 22 of 22


 
Forum Jump


All times are GMT -8. The time now is 11:22 PM.