Honda-Tech - Honda Forum Discussion

Notices
Search: Posts Made By: serious crx
Showing results 1 to 11 of 11
Search took 0.89 seconds.
Forum: Honda CRX / EF Civic (1988 - 1991)
08-31-2002, 04:00 PM
Replies: 46
Views: 1,153
Posted By serious crx

Re: How to take off crank shaft pulley? HELP ASAP (GroundZer0)

are u even going the right way righty tighty lefty loosey
Forum: Honda CRX / EF Civic (1988 - 1991)
08-29-2002, 08:09 PM
Replies: 19
Views: 3,572
Posted By serious crx

Re: Can I use a shift light to activate VTEC? (Mista Bone)

90 hf ls motor 81.5 endyne mid domes
intake,hedder
75 zex 11.71 108mph
7.67 94mph
ever heard if an a-1 cable transmission

pass was ran on 20/8/14 slicks
Forum: Honda CRX / EF Civic (1988 - 1991)
08-29-2002, 08:04 PM
Replies: 16
Views: 592
Posted By serious crx

Re: Fast N/A Project (EF8_SiR)

u need a 1.8 or more i have a ls motor in my crx intake hedder i run 13 flat and its stock with a one layer head gasket ls ls/vtec or vtec it doesnt matter as londg as its a 1.8 or
Forum: Honda CRX / EF Civic (1988 - 1991)
08-29-2002, 07:51 PM
Replies: 6
Views: 792
Posted By serious crx

Re: alignment of the intake cam and distributor? (adamjoey)

the distributer is 180 degrees off
Forum: Honda CRX / EF Civic (1988 - 1991)
08-29-2002, 07:43 PM
Replies: 23
Views: 898
Posted By serious crx

Re: traction in a CRX with a GSR motor? (sno0per)

the only way to really solve your tracktion problems is to find a really stiff rear springs and try nitto nt555r's that combo should be the best for street driving
Forum: Honda CRX / EF Civic (1988 - 1991)
08-29-2002, 07:40 PM
Replies: 46
Views: 1,153
Posted By serious crx

Re: How to take off crank shaft pulley? HELP ASAP (GroundZer0)

take the wheel off put the ratchet on the bolt and get a jack handle or a big bar have someont hit the brakes so the pully wont spin stand on the bar use quick solid hits or just get a...
Forum: Drag Racing
08-25-2002, 08:22 PM
Replies: 12
Views: 15,626
Posted By serious crx

Re: Home-made Lexan/Plexiglass windows (highbrid)

i used the old windo as templates and even installed the windos in the doors
if u make them excatly the sam u can even roll them up and down it just takes some patients
Forum: Drag Racing
08-25-2002, 08:17 PM
Replies: 14
Views: 1,869
Posted By serious crx

Re: Anyone before/after with lightened flywheel??? (SIINSI)

ha nonvtec 1.8 in a crx with only a set of endyne 81.5's ran 12.90's on 20x6's
Forum: Drag Racing
08-25-2002, 08:15 PM
Replies: 14
Views: 1,869
Posted By serious crx

Re: Anyone before/after with lightened flywheel??? (hot_EG)

never had problem ever even with 12.1 compression and a 7 pounder on pump gas in the heat of the day!!!!

but the weight of the stock wheel does keep it moving eiser that is very tru
Forum: Drag Racing
08-25-2002, 08:08 PM
Replies: 14
Views: 1,869
Posted By serious crx

Re: Anyone before/after with lightened flywheel??? (b16a4me)

my crx used to run 8.90's with my nonvtec 1.8 stock flywheel weighs 18 lbs
my 60 fts were high 1.90's in the 1/8 mile

all i did was replace the flywheel with a fadanza 8 pounder

now i run low...
Forum: Honda CRX / EF Civic (1988 - 1991)
08-25-2002, 07:48 PM
Replies: 33
Views: 865
Posted By serious crx

Re: b series swap in HF..why so much more pain? (Corporal-Jeff)

si and hf wiring harnesses are the same
if u are using a nonvtec u will need 90-91 integra distributer
si steering knuckles
90-93 non vtec axles they made a gsr in 92-93 so dont get those
motor...
Showing results 1 to 11 of 11


 
Forum Jump


All times are GMT -8. The time now is 06:17 PM.