Honda-Tech - Honda Forum Discussion

Notices
Search: Posts Made By: tbisme
Showing results 1 to 21 of 21
Search took 0.98 seconds.
Forum: Tech / Misc
01-03-2003, 07:51 PM
Replies: 1
Views: 466
Posted By tbisme

Re: Found bad connecting rod bearing, now what? (Angry Joe)

Check the factory tolerances and mike the thing , this is the only way to tell if it is within the range . make shure you mike it in more than one location on the jornal this will insure it is...
Forum: Tech / Misc
01-03-2003, 07:29 AM
Replies: 7
Views: 449
Posted By tbisme

Re: Injectors and ECUs (RaceTilIDie)

I set the timimg barely ahead of the stock location based on my factory service manual specs. Isn't the timimg controlled by the ECU or not? Becasue it did not make much difference even way advanced....
Forum: Tech / Misc
01-03-2003, 07:20 AM
Replies: 7
Views: 449
Posted By tbisme

Re: Injectors and ECUs (RaceTilIDie)

Are you talking about reprogramming the ECU? I heard that was a no-no because you cannot get back to your baseline. What do you think? Would only an FPR dial it back just the wee bit that I need? It...
Forum: Tech / Misc
01-03-2003, 06:11 AM
Replies: 7
Views: 449
Posted By tbisme

Re: Injectors and ECUs (RaceTilIDie)

. Race, do you think 20psi will make it run to lean? Thats not fair to ask you that considering you dont know my exact situation. Anyway i was more concerned with how the ecu would react to the...
Forum: Tech / Misc
01-03-2003, 05:14 AM
Replies: 7
Views: 449
Posted By tbisme

Injectors and ECUs

I am trying to bone up on this computer controled fuel system. I am used to carborators. I have been reading in the tech archives about Honda fuel systems and I need to know a few things - any help...
Forum: Tech / Misc
01-02-2003, 07:44 PM
Replies: 6
Views: 756
Posted By tbisme

Re: does performance intake & other performance parts take away from good gas mileage? (exospeedAMcr

[QUOTE], so its really all in tuning. basically, the more efficient you make your engine (more hp), the better the gas mileage it gets.

that is so true Its not hard to understand , dialing...
Forum: Tech / Misc
01-02-2003, 06:59 PM
Replies: 15
Views: 534
Posted By tbisme

Re: SOHC experiment! (T-sohctec)

if your buget is 300.00 ,you better stay with stock parts and build a good combo eng. What you said earler made sence with your buget restrictions.
Forum: Tech / Misc
01-02-2003, 03:36 PM
Replies: 12
Views: 2,261
Posted By tbisme

Re: D16-v-tec Running to rich (tbisme)

[QUOTE]If you decrease rail pressure will the injector atomize properly?


what psi. is to low ? before having to move to a chip or apex controler to back off on my fuel,what about changing my...
Forum: Tech / Misc
01-02-2003, 03:24 PM
Replies: 15
Views: 534
Posted By tbisme

Re: SOHC experiment! (T-sohctec)

I saw a y8 manifold on ebay last week I was at 75.00 I bid 90.00 it sold for 122.00 just keep looking there around.

https://honda-tech.com/forums/images/smilies/emwink.gif
Forum: Tech / Misc
01-02-2003, 03:08 PM
Replies: 12
Views: 2,261
Posted By tbisme

Re: -v-tec Running to rich (Benj)

benj, ajusting your cam could make a differance,but first try upgradeing your ignition system coil, cap, plugwires, plugs . This will help the fuel burn, then if you want to buy a ignition box you...
Forum: Tech / Misc
01-02-2003, 02:15 PM
Replies: 4
Views: 500
Posted By tbisme

Re: running rich?? (sslude)

Well, I ran a thread about my d16z6 running too rich and some tried to say that ... no fuel---no power ... and that more is better . There is definatly is a optimum air fuel mixture. It all depends...
Forum: Tech / Misc
12-24-2002, 12:36 PM
Replies: 12
Views: 2,261
Posted By tbisme

Re: -v-tec Running to rich (tbisme)

does anyone know what the safe range is ? ( reading on a digital a/f gauge) this one shows voltage from sensor. now im trying to lower the injector pressure W/a man. pressure reg..... hope to get a...
Forum: Tech / Misc
12-24-2002, 11:21 AM
Replies: 1
Views: 421
Posted By tbisme

Re: D16Z6 Rebuild (Knight2000)

start with "sohc upgrades" thread by spade and go from there . there are many ways to go w/ stroke, cams, head swaps for compression , pistons ,ect. Just look around in the search for some...
Forum: Tech / Misc
12-24-2002, 08:03 AM
Replies: 3
Views: 374
Posted By tbisme

Re: Ditgital Gauges (EgSick)

air fuel gauge.....

www.gadgetseller.com (http://www.gadgetseller.com) these are cool...
Forum: Tech / Misc
12-23-2002, 04:03 PM
Replies: 8
Views: 4,510
Posted By tbisme

Re: gear ratios - d16z6 vs d16y8 (bleh)

What is the reason for the change did your z6 not hold up?
Forum: Tech / Misc
12-23-2002, 03:48 PM
Replies: 8
Views: 4,510
Posted By tbisme

Re: gear ratios - d16z6 vs d16y8 (willyboyD16)

I have a d16z6 in my si and was wondering how mutch the tranny would take. Are the raitos the same? I put 17" weeles on mine and it slowed it down...... 1/8 mi track. I would like to find a...
Forum: Tech / Misc
12-23-2002, 02:50 PM
Replies: 12
Views: 2,261
Posted By tbisme

Re: D16-v-tec Running to rich (95siHaTcH)

Don't you think leaning it out will make it run more effeciently, more power, etc. ?
I do know lean is mean...
Forum: Tech / Misc
12-23-2002, 02:27 PM
Replies: 12
Views: 2,261
Posted By tbisme

Re: D16-v-tec Running to rich (3 South)

If you decrease rail pressure will the injector atomize properly? And what kind of instrument do you need to achieve air fuel readings and do most wheel dyno places have them? Decreasing fuel...
Forum: Tech / Misc
12-22-2002, 01:14 PM
Replies: 12
Views: 2,261
Posted By tbisme

-v-tec Running to rich (Help!)

I have a civic-si and installed a new cold air intake and cat-back exaust . Still passes emissions (barely), bought car new, never had rich problems. Now excessive black bumber syndrome and lost...
Forum: Tech / Misc
05-19-2002, 06:42 AM
Replies: 1
Views: 559
Posted By tbisme

milling your head (how much is to much)...?

[B]My D16z6 Eng. Blew the head gaskit ,It warped my head and I was going to mill .030 off but I"m wondering about the cam timeing ,piston to valve clearance,and how mutch compresion gain can I expect...
Forum: Tech / Misc
05-19-2002, 05:28 AM
Replies: 0
Views: 243
Posted By tbisme

Milling your head, ( how much is to much)?

[B]D16z6 [B] I blew the head gaskit, head is warped about 7 to 10 thous.I was going to go about 0.30 to boost my compression what do you think it will do to my cam timeing guys, thanks
Showing results 1 to 21 of 21


 
Forum Jump


All times are GMT -8. The time now is 12:54 AM.