Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 11
1
2
3
Last »
Search: Posts Made By: slooowDX
Showing results 1 to 25 of 269
Search took 1.75 seconds.
Forum: Vehicles for sale
03-13-2003, 12:55 PM
Replies: 2
Views: 454
Posted By slooowDX

Re: 92 Civic DX hatch 4 sale SO CAL (slooowDX)

ttt...am i asking too much?
Forum: Vehicles for sale
03-12-2003, 07:00 PM
Replies: 2
Views: 454
Posted By slooowDX

Re: 92 Civic DX hatch 4 sale SO CAL (slooowDX)

ttt, cmon someone gotta wanna get at it https://honda-tech.com/forums/images/smilies/h-emblem4.gif
Forum: Vehicles for sale
03-12-2003, 07:49 AM
Replies: 2
Views: 454
Posted By slooowDX

92 Civic DX hatch 4 sale SO CAL

92 Civic DX Hatchback Tahitian Green

18X,XXX miles on chassis

45-50K on 94 JDM GSR swap

Clean title, no rust, CA car all its life

Includes the following -
Forum: Honda Civic / Del Sol (1992 - 2000)
03-09-2003, 11:33 AM
Replies: 10
Views: 2,629
Posted By slooowDX

Re: Vents Only blows HOT air (FifthGearOnline)

control valve is stuck open, check by the firewall where the heater hoses go through, make sure whoever did the swap didnt mess up the linkage that controls the valve ...
Forum: Tech / Misc
03-03-2003, 05:27 PM
Replies: 6
Views: 866
Posted By slooowDX

Re: How to get 13" wheels over GSR brake rotors...? (integra6650)

yeah what kind of rims are you using? lenso's will fit over the GSR brakes, as far as bogarts, you need a spacer, and if your going to use a spacer, it would be advised that you have extended wheel...
Forum: Honda Civic / Del Sol (1992 - 2000)
02-26-2003, 07:01 PM
Replies: 75
Views: 3,401
Posted By slooowDX

Re: My engine bay (COLORPROS)

ground goes to the 10mm valve cover nut on the left, and about the AEM, if you want 3 inch, you gotta get one for a type R, nice car btw https://honda-tech.com/forums/images/smilies/emthup.gif
Forum: Tech / Misc
02-25-2003, 04:54 PM
Replies: 5
Views: 466
Posted By slooowDX

Re: Odyssey brakes (rabstg)

not up to the job? what kind of driving do you do man!! you have a van. are you talking about in emergency situations? you can get your factory rotors crossdrilled if you can't find any...
Forum: Honda Civic / Del Sol (1992 - 2000)
02-11-2003, 07:19 PM
Replies: 2
Views: 423
Posted By slooowDX

Re: Lincoln Mark VII HIDs in my 99 Si (mechanik)

it most likely can be done with some custom work, but you need more than just the bulbs, you need the balasts as well, and a way to wire them up, if you're just getting the headlights, then they wont...
Forum: Tech / Misc
02-09-2003, 02:01 PM
Replies: 1
Views: 391
Posted By slooowDX

Re: Failed CA smog w/ Z6 head on CRX (whybother)

ECU should be going into closed loop at idle, of course after engine is at normal operating temp...check your o2 and if its not that, i'd buy a new cat....190k is kinda a lot, by the HC reading at...
Forum: Tech / Misc
01-19-2003, 06:53 PM
Replies: 7
Views: 550
Posted By slooowDX

Re: B18C headbolt ?? (22lbGS-R)

i've re-used stock headbolts b4, never had any problems, i understand they stretch, but once or twice should be ok for a pretty much stock engine. anyone else kno if the GSR bolts will work with a...
Forum: Tech / Misc
01-19-2003, 05:28 PM
Replies: 7
Views: 550
Posted By slooowDX

B18C headbolt ??

i did a search on headbolts, didn't really find anything. can i use my GSR headbolts on a B16A or will they be too long? i really dont want to have to buy new stock bolts for this junker B16A im...
Forum: Honda Civic / Del Sol (1992 - 2000)
01-15-2003, 08:14 PM
Replies: 48
Views: 1,646
Posted By slooowDX

Re: How Do You Make Blinkers Blink Faster (Jawad)

that ish is so 1993 https://honda-tech.com/forums/images/smilies/emthdown.gif https://honda-tech.com/forums/images/smilies/emthup.gif do it if you like it i guess, just attracts more attention...
Forum: Honda Civic / Del Sol (1992 - 2000)
01-13-2003, 06:16 PM
Replies: 12
Views: 704
Posted By slooowDX

Re: itr muffler on EH help PLEAZE! (nerdsports)

i've seen topics on this a while back, i thought one of the guys just cut the tip shorter, that looked good and then he modified the piping, shortened i think, i dont think you have to cut off the...
Forum: Honda Civic / Del Sol (1992 - 2000)
01-06-2003, 11:19 PM
Replies: 3
Views: 4,474
Posted By slooowDX

Re: jdm b16a block w/ usdm b16a2 head....powerloss? compression? (zzZZzzleeperCX)

SiR II block (2nd gen) should have P30 slugs, and with the 00 Si head, identical to an SiR II head, compression will be 10.4:1, if you had PR3 slugs, then compression would be 10.2:1, all this is of...
Forum: Honda Civic / Del Sol (1992 - 2000)
12-30-2002, 05:50 PM
Replies: 49
Views: 1,473
Posted By slooowDX

Re: Hybrid guys: what radiator setups you runnin in your EG's? (B18C-EJ1)

i've got a koyo aluminum radiator, payed 350, works great, with my stock radiator the fan would come on once i came to a stop, with this one it rarely comes on. i've has such bad luck with the stock...
Forum: Tech / Misc
12-29-2002, 12:19 PM
Replies: 6
Views: 429
Posted By slooowDX

Re: Breaking in my built B16???? (airborne84000)

try not to drive on the fwy/hwy, like others have sed dont keep the RPM constant. make sure to vary the RPM, even if you do HAVE to drive on the fwy/hwy. 1000 miles should be good for the rings to...
Forum: Tech / Misc
12-28-2002, 05:14 PM
Replies: 5
Views: 513
Posted By slooowDX

Re: what cams to run and be safe wit milled head (tmex05)

im running skunk2 stage 2's in my jspec gsr w/ my head milled .030, and its been running fine for about 6000 miles. i asked a similar question on this board and many people told me just measure valve...
Forum: Tech / Misc
12-27-2002, 05:48 PM
Replies: 2
Views: 331
Posted By slooowDX

Re: Timing Belt Help (vtek)

http://www.helminc.com - factory manuals, buy one if you've never done one and plan on doing it yourself https://honda-tech.com/forums/images/smilies/emthup.gif
Forum: Tech / Misc
12-27-2002, 05:44 PM
Replies: 8
Views: 411
Posted By slooowDX

Re: Removing head..anything to watch out for?? (PressurizedSi)

i believe the headbolt torque is 66 ft/lbs...someone check me on this... umm..just make sure you have a good breaker bar to loosen the headbolts, even tho its only 66 ft/lbs, those things sometimes...
Forum: Honda Civic / Del Sol (1992 - 2000)
12-24-2002, 04:27 PM
Replies: 32
Views: 1,505
Posted By slooowDX

Re: Finally pics of my 92 VX (gsr_vx_hatch)

sleeper...not bad...but take the rest of the A/C stuff out https://honda-tech.com/forums/images/smilies/emthup.gif
Forum: Tech / Misc
12-15-2002, 04:36 PM
Replies: 1
Views: 299
Posted By slooowDX

Re: stuff you hook up to a vacuum line that makes your car smote.... (1point5)

like a fuel system cleaner? i work at honda and we have this fuel system cleaner you run in the motor through a vacuum port on the intake mani. it works well, i kno this because we did it on this POS...
Forum: Tech / Misc
12-15-2002, 04:31 PM
Replies: 9
Views: 1,019
Posted By slooowDX

Re: i think im loosing coolant, any ideas? (drdavidge)

how long ago have you flushed your coolant? and who did it? if the coolant system wasnt "burped" properly it will keep sucking in coolant from the overflow tank untill it gets full. try filling up...
Forum: Honda Civic / Del Sol (1992 - 2000)
12-11-2002, 07:02 PM
Replies: 46
Views: 2,080
Posted By slooowDX

Re: Got my **** VIS CF LIP TODAY (Soulless)

i believe the wheel's are old school Sprint Hart CP-R's, hope im not mistaken, car looks pimp https://honda-tech.com/forums/images/smilies/emthup.gif ...
Forum: Tech / Misc
12-04-2002, 07:07 PM
Replies: 1
Views: 2,618
Posted By slooowDX

Re: Changing rear brake pads on 95 Integra LS (GS-RoJa)

what do you mean? are the pads the same? no, rear pads are smaller and MORE expensive..haha, ummm changin them is similar to changing the fronts. most honda rear calipers have two 12mm bolts that...
Forum: Tech / Misc
12-03-2002, 07:51 PM
Replies: 36
Views: 2,214
Posted By slooowDX

Re: How can you tell the difference between a jdm engine and a usdm engine. (averageJoe)

i also have a 94 JDM B18C (SiR-G) engine, and it has a VTEC pressure switch, and like the above post states, i think its the later year JDM motors when they switched to the single wire VTEC...
Showing results 1 to 25 of 269
 
Page 1 of 11
1
2
3
Last »


 
Forum Jump


All times are GMT -8. The time now is 06:24 PM.